Compaq 207590-B21 - Power Distribution Unit Strip Quick Installation Instructions

Category
Power distribution units (PDUs)
Type
Quick Installation Instructions

Compaq 207590-B21 - Power Distribution Unit Strip is a rack-mounted dual input power distribution unit that offers maximum flexibility for utilizing rack space while providing protection against electrical line surges and spikes. It comes with 12 receptacles on 4 circuit breakers, enabling you to connect multiple devices and distribute power efficiently. Each load segment has a maximum output rating of 10A, and the maximum output rating of the unit is 24A. The unit features two LEDs on the front that indicate input power, and illuminated circuit breakers that indicate output power.

Compaq 207590-B21 - Power Distribution Unit Strip is a rack-mounted dual input power distribution unit that offers maximum flexibility for utilizing rack space while providing protection against electrical line surges and spikes. It comes with 12 receptacles on 4 circuit breakers, enabling you to connect multiple devices and distribute power efficiently. Each load segment has a maximum output rating of 10A, and the maximum output rating of the unit is 24A. The unit features two LEDs on the front that indicate input power, and illuminated circuit breakers that indicate output power.

About This Device
Kit Contents
1. Dual Input Power Distribution Unit
2. Additional cables - IEC-320 jumper cables (2)
3. Assembly, 0U/1U mounting hardware
Mounting brackets - 0U (2)
Mounting brackets - 1U (2)
Rail assembly for rack mounting (assembly required) - 1U
Rail, front 1U (2)
Rail, rear 1U (2)
Nut, wing (4)
Nut, metric hex (4) [recommended when shipping in a rack.]
Cage nuts - (4) [2 extra]
Screws mounting brackets to unit (6) [2 extra]
Screws mounting rails/brackets to rack (10) [2 extra]
Screws mounting unit (0U) to rack (6) [2 extra]
4. Tie wraps (15) [several extra]
This guide serves as an outline to assist qualified personnel with the installation
of the Compaq Dual Input Power Distribution Unit (PDU).
The input voltage for this model Dual Input PDU is 200VAC to 240VAC.
This Dual Input PDU includes the following features:
Mounts in either 0U or 1U configuration, offering maximum flexibility for
utilizing rack space
Provides 12 receptacles on 4 circuit breakers for rack-mounted devices
Protects against electrical line surges and spikes
This Dual Input PDU is used with information technology equipment.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS - This Quick Installation Guide contains
important instructions for the rack-mounted Dual Input PDU that should be
followed during installation.
Use screws (two on each side) to attach brackets to sides of unit. Secure unit
to side of rack by using screws (two on each side) to attach unit. Refer to the
1U configuration for installation of the cage nuts to secure screws to rails.
Installing the Unit - 0U Configuration
1
3
1
1
1
3
3
WARNING: There is a risk of personal injury from electrical shock and
hazardous energy levels. The installation of options and routine
maintenance and service of this product must be performed by
individuals who are knowledgeable about the procedures, precautions,
and hazards associated with AC power products.
Regulatory Compliance Information
All regulatory certifications for this product were obtained under the agency
series numbers EO3020 for the North American model and EO3020i for the
International model.
Please refer to the Important Safety Information (guide included with the Dual
Input PDU kit) before installing this product.
Important Safety Information
Read Before Installing Product
NOTICE
The information in this publication is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR
TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN,
NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS
INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER
CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR
STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE
AND AGAINST INFRINGEMENT.
This publication contains information protected by copyright. No part of
this publication may be photocopied or reproduced in any form without
prior written consent from Compaq Computer Corporation.
© 2000 Compaq Computer Corporation
Printed in the U.S.A.
Compaq, Registered U.S. Patent and Trademark Office.
DUAL INPUT POWER DISTRIBUTION UNIT KIT
QUICK INSTALLATION GUIDE
Second Edition (January 2001)
Part Number 192066-022
Compaq Computer Corporation
DUAL INPUT POWER
DISTRIBUTION UNIT KIT
Printed on recycled paper
Read Guide Completely Before
Beginning Installation Procedures
Quick Installation Instructions for
Rack-Mounted Dual Input Power Distribution Unit
192066-022
~A
1
2
3
4
~B
2
2
1
1
R
F
2
2
A ground bonding screw is provided on the rear of the unit as an attachment point
for conductors, should the rack contain any conductors used for the purpose of
grounding or bonding of ungrounded metal parts. (Ground cable not included.)
Use screws (two on each side) to attach brackets to sides of unit. Slide unit
into rails and secure by using screws (one on each side) to attach unit.
Installing the Unit - 1U Configuration
2
Utilizing the Ground Bonding Screw
3
Align 1U installation template (included) with holes in rack.
Place rear rail over the studs in the front rail . Tighten nuts finger tight. The
mounting tab will be facing out, so the holes align with the rack sides. Adjust
length of rail assembly to fit inside rack. Tighten either the wing nuts or hex nuts.
Insert cage nut (one on each side) in rack. Set hooks at rear of rail over holes in
rack. Use screws (one on each side) to attach rails to rear of rack through cage
nut. Use screws (two on each side) to attach rails to front of rack.
R F
Make sure that the devices connected do not exceed the unit capabilities.
This Dual Input PDU features three receptacles per circuit breaker, for a total of
twelve receptacles.
Each load segment has a maximum output rating of 10A. If the total connected
load exceeds 10A, the circuit breaker will trip and interrupt power to all
connected loads.
The maximum output rating of this Dual Input PDU is 24A. If the total load
connected to all load segments exceeds the rated amperage, the circuit breaker at
the wall could trip and interrupt power to all connected loads.
Regarding the Circuit Breakers
Input power can be verified by the illumination of the two LEDs on the front of
the unit, marked ~A and ~B.
Output power can be verified by the illumination of the circuit breaker, when in
the On position.
If a connected device is not powered, verify the respective circuit breaker is On
and illuminated.
If power is still not restored, contact your authorized Compaq service
representative at 1-800-OK-COMPAQ (1-800-652-6672).
For continuous quality improvement, calls may be recorded or monitored.
For additional information, visit the Compaq website: www.compaq.com.
~ A
~ B
~A
1
23
4
~B
OFF
ON
OFF
ON
OFF
ON
OFF
ON
2
OFF
ON
~ A
~ B
Installation is complete.
Connecting Devices
4
WARNING: To reduce the risk of personal injury resulting
from electric shock, do not remove the cover from the
Power Distribution Unit. There are no field-serviceable or
user-serviceable components inside.
  • Page 1 1
  • Page 2 2

Compaq 207590-B21 - Power Distribution Unit Strip Quick Installation Instructions

Category
Power distribution units (PDUs)
Type
Quick Installation Instructions

Compaq 207590-B21 - Power Distribution Unit Strip is a rack-mounted dual input power distribution unit that offers maximum flexibility for utilizing rack space while providing protection against electrical line surges and spikes. It comes with 12 receptacles on 4 circuit breakers, enabling you to connect multiple devices and distribute power efficiently. Each load segment has a maximum output rating of 10A, and the maximum output rating of the unit is 24A. The unit features two LEDs on the front that indicate input power, and illuminated circuit breakers that indicate output power.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI