Vista VVRD28V12DN-650 Installation guide

Brand: Vista

Model: VVRD28V12DN-650

Category: Security cameras

Type: Installation guide

VVRD28V12DN-650

Installation manual

Ultra Hi-resolution (650TVL), vandal

resistant, day/night, vari-focal dome.

Including scene analytics and alarm

output functions

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the m

anufacturer‟s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plu

g. A polarized plug has two blades with one wider than the other. A gro

unding type plug has two blades and a third grounding prong. The wid

e blade or the third prong are provided for your safety. If the provided p

lug does not fit into your outlet, consult an electrician for replacement o

f the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from th

e apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use

aution when moving the cart/apparatus combination to avoid injury

from tipping over.

13. Unplug this apparatus during lightning storms or when unused for long

periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-su

pply cord or plug is damaged, liquid has been moisture, does not oper

ate normally, or has been dropped.

15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE

BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE

RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING

OTHER THAN THAT CONTAINED IN THE OPERATING

INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

16. Use Certified/Listed Class 2 power source only.

CONTENTS OF PACKAGE

The package contains the following

Camera in Housing -----------------------------1no

Instruction Manual (This Document)--------1no

Accessory Kit for Installing -------------------1no

Drilling guide label ------------------------------1no

TABLE OF CONTENTS

INTRODUCTION --------------------------------------------------------------------------------------- 4

CAMERA CONNECTIONS -------------------------------------------------------------------------- 6

INSTALLATION ----------------------------------------------------------------------------------------- 8

LENS ADJUSTMENT --------------------------------------------------------------------------------- 9

DC AUTO IRIS LENS --------------------------------------------------------------------------------- 9

OPERATING CAMERA ------------------------------------------------------------------------------- 9

CAMERA ADJUSTMENT ---------------------------------------------------------------------------- 9

EXTERNAL DIMENSION----------------------------------------------------------------------------- 20

SPECIFICATIONS ------------------------------------------------------------------------------------- 21

INTRODUCTION

The camera provides high-quality image using a Sony Wide Dynamic 1/3” Super-HADII

PS 960H (Effio) CCD and digital signal processing LSIs.

Features:

1/3” Super-HADII PS 960H CCD (Sony Effio)

Super high-resolution of 650TV lines

0.4 lux(Colour), 0.04 lux(B/W), 0.001 lux(Low-Shutter) @ F1.4 Sensitivity

Auto Electronic Shutter [1/50 ~ 1/100,000] and manual electronic shutter

modes [1/50 ~ 1/10,000]

On Screen Display (OSD)

Auto and Manual white balance modes

Supports Line-Lock external synchronization

Digital PTZ

Digital Effect (H/V reverse, 180 degree rotate, inverse, freeze)

2D-NR, 3D-NR (DNR Demo)

Back Light Compensation

Back Light Masking (MAX. 15 area)

Excessive High-Light Compensation

Wide Dynamic Range (~x512)

Various Detection Methods (zone detection, motion trace, face trace, mine

area, absent detection, cross object counting, entrance counting)

Day & Night(Auto, Manual, External, Filter delay)

Various Alarm Methods (Period, Snooze, Polarity Select)

Privacy Mask or Mosaic (MAX. 15 area/4-point polygonal/transparency)

Scene Change Detection

Sens-Up (~x32)

White Pixel Removal

Frame Control (Auto, 1~7 sec)

System Lock (4-Digit password)

RS-485 Remote camera control

F1.4 D&N DC iris vari-focal lens

Operates in 12VDC or 24VAC

Use Certified / Listed Class 2 power source only

CAMERA CONNECTIONS

Connection Cable Description

COLOR

Description

RED

AC24V/DC12V

WHITE

AC24V/DC12V

ORANGE

ADKEY

BROWN

GND

BLUE

RS485(-)

GREEN

RS485(+)

YELLOW

ALARM OUT

GREY

DN EXT-IN

BLACK&WHITE

DN EXT-OUT

BLACK

GND

SKY BLUE

Not used

PINK

Not used

1) External Day/Night Control: To select Day/Night mode using external equipment,

connect control lines to the appropriate terminals.

 DAY & NIGHT OUTPUT (Black / White)

This function allows the switching on of an external device such as lights, when

the camera switches to its night time mode. The Day/Night mode in the OSD

menus must be set to “AUTO”

 DAY & NIGHT EXTERNAL INPUT (Grey)

This function allows the cameras Day/Night Switching to be controlled by an

external switch such as a Photo Cell. The Day/Night mode in the OSD menu

must be set to “External”

2) Alarm out (5vTTL)

 Event detection signals are output through this port. (YELLOW AND GND)

 Active state is configurable.

 Low going high in alarm (approx 3.5v > 5v)

Gray

Black

GND

Black

DAY&NIG

Black/ White

5V/10mA : IR LED ON (NIGHT)

0V : IR LED OFF (DAY)

2) Power Input Terminal

 RED: +

 WHITE -

If using a 12vDC PSU then it is recommended it is not less than 0.75A.

4) Camera Control

 GREEN: RS485+

 BLUE: RS485-

5) AD Control via optional hand held set up controller (VZM22/REM)

GND Terminal/Brown

AD Key

INSTALLATION

1. Loosen the four torx screws located midway up the front of the housing leave the

screws loose in the front portion. (Fig. 1)

2. Drill the mounting location, using the bottom of the housing as a Drilling guide label.

(Fig. 3)

3. Attach the housing to the ceiling using suitable fasteners, M6x35 tapping screws are

supplied only use if they are suitable. (Fig. 3)

4. Close the housing using the loosen torx screws. (Fig. 2)

Torx screws

M5x10 (4x)

Torx screws

M5x10 (4x)

Seal around

the housing

base tightly

using

the silicon

rubberTorx

screws

M5x10 (4x)

Figure 1

Figure 2

LENS ADJUSTMENT

DC AUTO IRIS LENS

2.8~12mm

Image Size

1/3" CCD

Focal Length

2.8-12mm 5%

Aperture

Ratio

1 : 1.4 5%

Angular

Field of View

(Degree)

Horizontal

2.8mm : 77

12mm : 21

OPERATING CAMERA (OSD menus)

Field of view: Adjust setting

from Telephoto (T) to wide (W)

field of View.

Focus: Adjust lens focus from

near (N) to infinity.

Key to button operation

1 – Service lead point

2 – Enter

3 – Up (U)

4 – Down (D)

5 – Left (L)

6 – Right (R)

Local setup of the camera can be achieved by connecting a portable monitor to the set up video

out put (No.6 in the image above).

The OSD menu can be accessed by pressing button No. 1. Navigation of the menus is achieved by

using the other buttons as detailed above.

Menu tree

CAMERA ADJUSTMENT

White Balance

1) Auto(Auto White Balance) : AWB mode (1800ºK ~10500ºK)

2) Push/Hold: Push & Hold Mode.

 To find the Optimal setting for the current environment, place a sheet of white

paper in front of the camera, select Hold and press the Enter button.

3) CRS Mode (Colour Rolling Suppression): Function is not used on this camera.

4) Outdoor: Sets the colour temperature to outdoor (6300ºK)

5) Indoor: Sets the colour temperature to indoor (3200ºK)

6) FL (Fluorescent Light): Sets the colour temperature for fluorescent lighting

conditions.

7) User (User Set White Balance): Adjust red or blue gain.

 R(R-GAIN):Adjust R-GAIN value (0-255)

 B(B-GAIN):Adjust B-GAIN value (0-255)

Auto Exposure

1) SHT(s)(Electronic Shutter) : Select Shutter mode.

 Auto (1/50 ~ 1/100,000) Auto run, Manual 8 step from (1/50 ~1/10,000).

2) FLC (Flicker-less): Flicker-less On/Off.

3) AGC(Auto Gain Control) : AGC Gain(Off, Low, Middle, High)

4) Sense-Up (Slow Shutter): Maximum Slow-Shutter select. (x2-x32 and Off)

5) Offset Add: Forces the picture to turn up in a low luminance environment.

BLC/WDR

1) Normal AE: BLC/WDR function off.

2) WDR (Wide Dynamic Range): Wide Dynamic Range mode on.

3) EHLC (Excessive High Light Compensation): EHLC mode on.

 The brightest part of the picture is blacked out to allow the other areas to be

viewed.

4) Auto (Auto Weighting BLC): Auto weighting BLC on.

5) Spot (User Setting BLC area): Spot metering mode on.

 Posi: OSD mode to adjust the position of the spot metering area.

 Size: OSD mode to adjust the size of the spot metering area.

6) Zone (Preset BLC area): Fixed metering area mode. (1-9).

Mask

1) Mask: Selects mask area to be set (1-15).

2) Func: Selects mask function (Privacy, BLM, Both, Off).

 Privacy: Area to be blanked out on the display.

 BLM: Back Light Mask.

 Select the are of the screen that will have excessive back light

illumination- when activated this helps to over come the problem of the

lens shutting down due to the bright areas of the pictures, so allowing the

other areas to be viewed in detail

 Both: Privacy function and BLM function on.

 Off: Function off.

3) Edit: Edit Mask area.

 Edit mode only available when FUNC set to ON

 Size: adjust the size of the Privacy and BLM mask area.

 Posi: adjust the position of the Privacy and BLM mask area.

 Tilt: adjust tilting of Privacy and BLM mask area.

 Colour: Select Privacy and BLM mask colour (0-14).

 Transparency: Select Privacy mask transparency (Default 3/0-3).

 Mosaic: Select Privacy and BLM mask mosaic On/Off

 Adj. Mosaic: Adjust Privacy and BLM mask mosaic level (0-31).

Detection (Analytics)

1) Func: Select Detection function.

Note: Only one type of detection can be used at anytime

 Zone: Area motion detection mode.

 Zone: Select Motion detection zone (Zone1-4).

 Func: Select Motion detection on/off.

 Size: Press Enter button followed by the U/D/L and R buttons to adjust

the size of the Motion detection area.

 Posi: Press Enter button followed by the U/D/L and R buttons to adjust

the position of the Motion detection area.

 Link Zoom: When set to ON the image will digitally zoom in when motion

is detected

 Motion Trace: When selected it will „box‟ the moving objects.

 Tracks an object through a scene and generates an alarm.

 Face Trace: Face Trace mode on.

 Tracks a face through a scene and generates an alarm.

 Sens Down: Lowering the value allows for wider judgment on facial

recognition. (0~127)

 Min Size: Minimum face size configuration (If this is set to 0 then no faces

will be detected).

Please be aware the facial recognition function is not 100% accurate and can produce

false alarms or miss faces being captured. Not recommended for as a primary alarm

source.

 Mine: Up to 4 areas of interest can be set. If motion occurs an alarm can be

generated

 Set Mine: Press the Enter button to Set Mine mode.

< >: Move the Mine Zone move using the Left and Right buttons.

UP: Sets the min in the required position.

DN: Clears the position of the mine

ENT: Press Enter to leave the Set mode.

 Clr All: Press the Enter button to clear all mine positions.

 Display: Select Mine Display On/Off. To show cross hairs of mine position

 Absent: Selecting the absent mode will produce alarms ands on screen displays

when an static object is removed from the scene or is placed in the scene

 Sens Down: The lower the number the more sensitive the function is.

 Alarms time out after a set period

In low luminance environment, the accuracy is reduced.

If the object is too big, the accuracy is reduced.

 Cross: This will count the number of movements from one zone to another in one

direction.

 Zone: Use the right arrow to select either Zone 1 or 2, the relevant zone

will flash for a short period.

 Size: Adjust the size of the selected zone.

 Posi: Adjust the position of the selected zone.

 Direction : Select Crossing direction 1>2 or 2>1

 Alarm Cnt: Set alarm out cross count. The alarm will be activated after

this number of counts.

 Reset Cnt: Manually resets the count to Zero. The count will

automatically reset after the Alarm count is reached

If an object is passing too fast through the two detection areas, the counting may fail to

operate. Then in this case, increase the space between the two zones or decrease the

size of the zones.

If the passing object is too long, counting results can be inaccurate. Then in this case,

increase the space between the two zones or decrease the size of the zones.

If two objects pass across the area in the same time, then results can be inaccurate.

 Entrance: Entrance counting mode. The object move in through the entrance,

counting number increases

 Size: Adjust the size of the entrance.

 Posi: Adjust the position of the entrance

 Alarm Cnt: Sets the number of entrance activations required to activate

an alarm

 Reset Cnt: Manually resets the count to Zero. The count will

automatically reset after the Alarm count is reached

1. Crossing objects are ignored

2. Multiple objects will not be detected.

3. If the distance is to long from the camera to entrance, the results can be

inaccurate.

2) Sens Down: Adjusts the Detection Sensitivity using left/right (L/R) Buttons. The lower

the figure the more sensitive the function is.

Picture/DNR

1) Sharpness: Adjusts the sharpness of outlines (0~15)

2) Resolution: Selects resolution mode (Low/Mid/High)

3) 2D-NR: Select 2D noise reduction level (0~6)

 2D-NR : Noise reduction on a frame

4) 3D-NR: Select 3D noise reduction level (0~31)

 3D-NR : Noise reduction through the several frame

5) DNR Demo: Select DNR Demo Display On/Off using the Left and Right Buttons

None DNR Effect

Display

DNR Applied

Display

Effect/Special

1) d-Effect (Digital Effect): Selects digital Flip/Rotate state (Off/Rotation/Mirror/V Flip )

2) Nega: Selects a negative image (on/off)

3) d-PTZ (Digital Pan, Tilt, Zoom): Adjust d-PTZ.

 Func: Press the Enter button to turn digital zoom on/off.

 Zoom: Use the Left and Right buttons adjust to digital zoom (0-255).

 Pan&Tilt: Press the Enter button to access the Pan&Tilt (needs to be zoomed in

to operate).

 Use the Left and Right buttons adjust to digital pan

 Use the Up and Down buttons adjust to digital tilt

 Press the Enter button to exit.

 PT Reset (Pan & Tilt Reset): Press the Enter button to reset digital pan and tilt.

4) Freeze: This freezes the image on/off

5) Frame Control: Select term of refresh rate for output video. This function is useful to

reduce the recording to data storage.

 Func: Select frame control mode to ON/OFF, and Auto.

 Auto mode: When motion is not detected, the video output is being

refreshed in the programmed interval. When the motion is detected,

output video is switched to real time video.

 ON: Always refresh in configured interval.

 OFF: Always real time video.

 Renewal (sec): Selects the interval between two frames.

Note: It may take a short time from motion being detected to switching to real time video

6) ScnChg/Unfoc: Select Scene Change/Unfocus detection On/Off.

 If the image that the camera is viewing changes, e.g. goes out of focus or moves.

(This could be caused by tampering or spraying with paint. An On Screen

message will be displayed.

 This function is linked with the alarm out

In low light environments, the accuracy will be reduced.

In very low light environments, the function will not operate.

The function ignores moving objects.

A. Title

B. Delete character

C. Character table

D. Command line

- Clear : Clear Title

- Cancel: Cancel editing

- Accept: Save Title

System Setup

1) Cam Info: Camera information display

 Cam ID/Baud rate/Protocol/Firmware Ver./CCD Type/Lens Type

2) General Setup

 System Lock: Configuration Lock.

 When system lock is set to “Lock”, User must to input 4-character

password to enter OSD menu.

Default password is “0000”.

 Change PID : Change the administrator‟s password

 Move cursor with OSD Key and Press Enter to input the character.

 Comm (RS485 Communication): Press the Enter button to access the Comm.

 Cam ID: Select the camera ID (001 - 255).

 Baud Rate: Select serial communication speed (2400/4800/9600/19200).

 Protocol: RS-485 protocol. (COMMAND / VISTA / FASTRAX / PELCO-D /

PELCO-P) ( Set to COMMAND when using hand held set up tool)

 Title: Edit camera title.

 Display: Selects the items to be displayed on screen.

 Cam ID: Camera ID display On/Off.

 Title: Title display On/Off.

Title Site_0

< > ENT:Del

Clear Cancel Accept

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

a b c d e f g h i j k l m

n o p q r s t u v w x y z

- . 0 1 2 3 4 5 6 7 8 9

 Alarm : The alarm output (Yellow and Black pair) can be activated by the

Detection or Scene change functions is configured as follows:

 Period: Alarm out period (5sec/10sec/20sec/30sec/1min/5min/Cont.)

 Snooze: Alarm out snooze(Off/5sec/10sec/20sec/30sec/1min/5min)

(This is the period of time before the alarm will become armed again after

an alarm has cleared)

 Active pol: Alarm output active state configuration. (Low, High)

(Low – N.O. High – N.C.)

 System Init

 Cancel: Back to General Setup Menu.

 Confirm: Initialize all data. (Factory Default)

3) Lens

 Iris : DC, Video, Manual Lens selected Iris : adjust AE Speed

 DC lens and video lens can adjust AE Speed

 Normal AE Ref (Auto Exposure Reference Level) : Press the Enter button to

access the AE Ref.

 Ref Lvl: Adjust AE base reference level.

 WDR Ref: Press the Enter button to access the WDR Ref.

 Ref Lvl: Adjust the WDR long-time control Base Reference Level.

4) LLC (Line Lock Control) : Press the Enter button to access the Line Lock mode.

 Func: Select Line Lock function On/Off using the Left and Right buttons.

 Phase: Adjust Line Lock sync phase using the Left and Right buttons. (0~100)

The LLC function is only available if the camera is powered by and AC source.

5) White Pixel

 Det Exe: Press Enter button to start the White Pixel Compensation mode.

 ENT to Adj: Press Enter button to start White Pixel Compensation mode.

 Proc: Process is running finding the white pixels. ( Please wait)

 Done: Process ended

 Det Count: Results of white pixel detection.( the number of white pixels)

 Func: Select erasing white pixel function On/Off using the Left and Right buttons.

 Det Level : Select the judgment level of white pixel using the Left and Right

buttons (1~16)

 Det View: Set to on will display detected white pixels.

6) Day/Night

 Mode: Select D&N mode.

 Auto: Filter operates automatically relative to AGC level.

 Day: The camera outputs the video image in colour only.

 Night: The camera outputs the video image in black and white only.

 Ext: The camera switches from Colour to mono on the input from an

external switch such as a Photo-cell. (Grey and Black)

 Night Mode : Select B/W Burst On/Off

 Delay(s): Adjust the delay before switching when D&N mode is Auto (1-60 sec).

 D>N Level: Select switching level Day to Night when D&N mode is Auto (0-15).

(The lower the number the darker the image before switching)

 N>D Level: Select switching level Night to Colour when D&N mode is Auto (0-15).

(The higher the number the brighter the picture before switching)

When user entered in main menu and sub-menus, following menus will be appeared.

I. Main Manu (menu in bottom lines)

A. Exit: Save & Exit.

B. Load: Load Default Value.

II. Sub Menu (menu in bottom lines)

A. Return: Return to previous menu.

B. Exit : Save & Exit

1) Exit Menu

 Save & Exit: Save the current settings.

 Exit: Exits without saving any changes.

2) Load Default Setup

 Yes: Loads the factory default settings.

 No: No operation, and return to previous menu.

EXTERNAL DIMENSION

Window Size

2.5mm,

impact-resistant P.C (LEXAN)

10cm diameter

Cable Entry

One 23mm opening holes

Weight – Unit:

Shipping:

700 g

960 kg

Page is loading ...

Vista VVRD28V12DN-650 Installation guide

Brand: Vista

Model: VVRD28V12DN-650

Category: Security cameras

Type: Installation guide

Download PDF

report

Vista VVRD28V12DN-650 Installation guide

Vista VVRD28V12DN-650 Installation guide

Related papers

Other documents