Digital 310
Multi-channel transmitter to control direction
Versions
Digital 310 868 MHz (Art.-Nr. 76 497)
Digital 310 433 MHz (Art.-Nr. 76 452)
Safety advice
Attention:
• Please read these instructions carefully
before you connect and operate this unit!
• Never control doors or other devices
before you have made sure that neither
persons nor objects are in the operating
range!
• Check regularly if the unit is ready for
transmitting!
• Have faulty units checked by the manu-
facturer.
• Do not manipulate the unit.
Operation / transmitter
• When you push one of the four priority channel
buttons or a sequence of the channel buttons and
then you push one of the direction buttons, a
command is transmitted.
• After you have released the buttons, the
transmitter is still active for approx. 18 seconds, so
that a transmission is still possible when you push
one of the direction buttons again.
Advice:
Please enter your channel number within
10 seconds.
• You have the possibility to save up to 999 codes.
• The priority channel buttons and the channel
buttons are already coded by factory.
• When you enter more than 3 digits, the last three
digits are saved in each caset.
• The transmitter transmits as long as a button is
pushed, but after 36 seconds it cuts out
automatically.
Learning
• Transmit the code of the multi-channel transmitter
to the RC remote control (see installation
instructions of the RC remote control of the unit
to be operated).
• The selection of channel is carried out by pushing
one of the four priority channel buttons or a
sequence of the channel buttons
(enter max. 3 digits) and then by pushing one of
the direction buttons.
Coding modes
Attention!
To be able to transfer a direction code (OPEN-STOP-
CLOSE) from one transmitter to another, both
transmitters (source and target transmitter) need the
feature of direction function.
If in doubt, please contact your dealer or the
manufacturer.
Learning:
Single button codes may be learned by already
existing transmitters and single codes of the
multi-channel transmitter can be transferred to other
transmitters.
Duplicating:
The codes of all buttons may be transferred
completely from one multi-channel transmitter to
another multi-channel transmitter.
Random coding:
Single buttons or button combinations of the
multi-channel transmitter can be programmed with
a new code.
Learning - hand transmitter to multi-channel
transmitter
1. Connect the source transmitter (hand transmitter)
and the target transmitter (multi-channel
transmitter) by means of the programming cable.
2. Hold button 2 of the target transmitter until LED
D glows.
3. Push the ENTER button. LED D flashes slowly.
4. Either enter the channel number on the target
transmitter or push a priority button on the target
transmitter that shall be re-learned. Then hold the
ENTER button until the learning process is termi-
nated (see step 5).
5. Push within 10 seconds the button on the source
transmitter the code of which shall be transferred
and hold it. LED D of the target transmitter
flashes quickly and glows for approx. 3 seconds
after the learning process is terminated. Then
release both buttons.
6. Remove the programming cable.
Learning - multi-channel transmitter to hand
transmitter
1. Connect the source transmitter (multi-channel
transmitter) and the target transmitter (hand
transmitter) by means of the programming cable.
2. Either enter the channel number on the source
transmitter and hold the ENTER button until the
learning process is terminated (see step 3) or push
the priority button on the source transmitter the
code of which shall be transferred and hold it
until the learning process is terminated.
3. Push the channel button on the target transmitter
that shall take over the code and hold it. The LED
on the target transmitter flashes quickly and
glows after the learning process is terminated.
Release both buttons.
4. Remove the programming cable.
Learning of single codes - multi-channel trans-
mitter to multi-channel transmitter
1. Connect the source transmitter and the target
transmitter by means of the programming cable.
2. Push button 2 of the target transmitter until LED
D glows.
3. Push the ENTER button.
The LED D flashes slowly.
4. Either enter the channel number on the target
transmitter or push the priority button on the
target transmitter that shall be re-learned. Then
hold the ENTER button until the learning process
is terminated (see step 5).
5. Either enter the channel number on the source
transmitter and then hold the ENTER button or
push the priority button on the source transmitter
the code of which shall be transferred and hold it.
The LED D on the target transmitter flashes
quickly and glows for approx. 3 seconds after the
learning process is terminated. Release both
buttons.
6. Remove the programming cable.
Cancel the learning process.
Push either direction button OPEN or direction
button CLOSE.
