TEAC EU2890ST Owner's manual

Brand: TEAC

Model: EU2890ST

Category: CRT TVs

Type: Owner's manual

TEAC EU2890ST is a TV set with a 70 cm diagonal and a visible screen of 66 cm. It supports PAL BG and NTSC standards, has 100 program slots, OSD (On Screen Display), a switch-off preset (0 to 120 min), and automatic switch-off after the end of program transmission. It features 2x Euro AV SCART input, antenna 75 Ohm, headphones, Y, Cb, Cr - component input on SCART1, mini DIN (SVHS), 3xRCA (video and audio), and a power consumption of 95 W during normal operation. TEAC EU2890ST is equipped with an infrared remote control that allows you to operate the TV from a distance.

WARANTY REGISTRATION

Please read this warranty card.

Keep your purchase receipt to enable you to proceed quickly in the event of a

Warranty Service.

Warranty Terms & Conditions

1. TEAC warrants to the original retail purchaser only, that this product is free from defects in material and

workmanship under normal domestic use and authorises free service during the warranty period at any TEAC

Authorised Centre only. TEAC warranty only applies to products purchased, used and serviced in Australia.

2. Subject to the terms herein, this warranty effectively covers the equipment as specified in the Warranty

Periods Table from the date of purchase.

3. All parts, except the external cabinet, are warranted as specified in Warranty Periods Table, and will be

repaired or replaced at the sole judgement of TEAC.

4. Normal customer maintenance as described in the owner's manual is not covered by this warranty (such as

cleaning VCR heads etc.)

5. This warranty does not apply to equipment showing abuse, damage or that it may have been tampered with,

altered or repaired outside any TEAC Authorised Service Centre. If so, the warranty will be void.

*Your nearest Authorised TEAC Service Centre is listed in your Owners Manual

6. In the event that this unit or any defective parts must be returned to TEAC Service Centres, a copy of this

warranty certificate and of your purchase receipt must be enclosed to be a valid warranty. Such equipment

or parts must be sent to the nearest authorised TEAC Service Centre. After the repair, the unit will be

available for collection by the owner or it will be returned to the owner. The warranty does not cover freight

or insurance. In all cases of in-transit damages or loss, a claim must be filed against the carrier by the

purchaser.

7. In home service will only be provided as part of this warranty if all the following conditions are met;

a) The product is a Colour Television of 59cm screen size or over.

b) The product is within the warranty period.

c) The product is located within the normal service area of the local TEAC Service Provider.

In any other situation or circumstance, where an in home service call is made, a service fee will be charged by

the Service Provider. TEAC Total Care in home service and installation is available at competitive rates.

8. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection

with the sale of any equipment other than as stated in this warranty and outlined above.

9. In no event will TEAC be responsible or liable for indirect or consequential damages from interrupted

operations or other causes.

10. Warranty is not transferable to any subsequent purchaser if the product is sold during the warranty period,

TEAC PRODUCT

Televisions

Televisions - Widescreen 16x9

Televisions - 59 cm and above

Digital Set Top Boxes

VCR

DVD

Audio Systems

1 Year

3 Years (In-Home Service Included)

1 Year (In-Home Service Included)

1 Year

WARRANTY PERIOD

• Power supply: • 230/50Hz

• Power consumption: • Stand-by: max. 0,5 W

• Normal operation: 95 W

• Connections: • 2 x Euro AV SCART input

• Antenna 75 Ohm

• Headphones

• Y, Cb, Cr - component input on SCART1

• Mini DIN (SVHS)

• 3xRCA (video and audio)

• Pisture tube: • Diagonal 70 cm - visible screen 66 cm

• Standard: • PAL BG

• NTSC (via SCART)

• Number of programmes: 100

• Displayed functions: OSD - On Screen Display

• Switch-off preset: 0 à 120 min.

• Automatic switch-off after the end of programme transmission

• Frequency synthesis

• Cable and hyperband channels: • VHF-1: 2 - 4

• VHF-3: 2 - 12

• UHF: 21 - 69

• S: S1 - S41

TECHNICAL SPECIFICATIONS................................................................................... 5

POSITIONING.......................................................................................................... 6

IMPORTANT WARNINGS - SAFETY RECOMMENDATIONS............................................. 6

CONNECTION.......................................................................................................... 6

INFRA-RED REMOTE CONTROL................................................................................. 7

CONTROL UNIT PANEL............................................................................................. 8

SWITCHING ON AND OFF......................................................................................... 9

SETTING TV PROGRAMMES...................................................................................... 10

ADJUST PICTURE AND SOUND................................................................................. 13

PICTURE FORMAT 16:9............................................................................................ 15

TELETEXT................................................................................................................16

DEMAGNETISATION OF THE PICTURE TUBE..............................................................18

TROUBLE SHOOTING............................................................................................... 18

TECHNICAL SPECIFICATIONS

CONTENTS:

SAFETY AND PRECAUTIONS

To ensure safe and reliable operation of the TV set, please observe the following precautions in installation,

operation and maintenance.

Attention:

1. Pay attention to the power supply cord before installing the TV set. Do not hang anything on the cord and avoid

treading on the cord.

2. The slots on the housing back are designed for ventilation to ensure reliable operation of the TV set and prevent

overheating. They must never be covered or blocked. The TV set must not be placed near a heat source or it

might be damaged.

3. The outdoor antenna must not be erected close to HV lines or other power supply lines. Use extreme care when

erecting the antenna and not to touch living wires or injury may occur.

4. This TV set can only use the supply voltage and frequency indicated on the back of the housing. If your power

supply does not comply with them, please consult with the service personnel.

5. Do not let any object fall into the ventilation opening of the TV set housing, not let any liquid flow into the

machine via the opening.

6. Do not subject the TV set rain or use it in a damp environment. Whwn cleaning dust, be sure to remove the

power supply plug from its socket first. Do not clean the housing with directly liquid detergent, p cloth. Be sure to

remove the power supply plug from its scocket and remove the antanna plug during a thunderstorm or when it

will not be used for long time to avoid components being damaged by lightning.

7. If you use an indoor antenna do not let it touch any electrical appliance or normal reception of TV programs may

be affected.

Safety:

1. Do not remove the back of housing by yourself, as high voltages inside the unit are dangerous. If it is necessary

to open the back, ask a technician with specialized service experience.

2. Remove the power supply plug from its socket in case of the following conditions and consult with service

personnel.

(1) The power cord or plug are damaged or shows crecking.

(2) Any object has fallen into or liquid flown into the TV set.

(3) The performance of TV set has deteriorated significantly or there is damage on the housing.

(4) The TV set will not operate normally according to the instructions.

3. Please remove the power supply plug from its socket when the TV set will not be used for a long period time.

CAUTION:

use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation

exposure.

This appliance has a serial number on the rear

panel. please record the serial number and retain it

for records.

Serial Number:____________________________

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO

NOT REMOVE COVER (OR BACK). NO USER SER

VICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

The exciamation mark within an equileterai triangle is intended to alert the user to the presence

of important operating and maintenance (servicing) instructions in the literature accompanyiing

the appliance.

The lighting flash with arrowhead symbol, with an equileteral triangle is intended to aiert the

user to the presence of Uninsulated "dangerous voltage" Within the product's enclosure that

may be of sufficient magnitude tr constitute a risk of electric shock to the person.

 ª ON/OFF (Stand-by)

 1-0 Programme selection /

Page selection (TT)

 AV

 MENU

 PICT

 SOUND

 Ï Mute (Sound off)

 p Menu up/down

Programme+ / Page+ (TT)

 t Menu up/down

Volume- / Analogue settings-

 OK Confirmation key

 u Menu up/down

Volume+ / Analogue settings+

 q Menu up/down

Programme- / Page- (TT)

 Red key

 Green key

 Yellow key

 Blue key

 † Teletext on / Mixed picture / Text off (TT)

 i

 STOP Stoppage of the subpages changing (TT)

¡ ZOOM Picture format /

¢ › Teletext-

£ ˆ

¤ N

¥ é Key has no function

þ The (TT) mark is for function in teletext mode

Switch over to AV mode

"MENU" menu on

"IMAGE" menu on

"SON Ç" menu on

/ Page- (TT)

/ Page+ (TT)

/ Page+10 (TT)

/ Page+100 (TT)

"INFO" menu on / Index page (TT)

Double height (TT)

Menu switch-TV, AV-TV, TV (TT)

Time display / Subpages on (TT)

Picture and sound normal /

Key ? (TT)

Battery compartment (on the rear side)

PR 106

1010

1111

1212

1313

1717

2121

1414

1818

2222

1515

1919

2323

1616

2020

2424

INFRA-RED REMOTE CONTROL

Insert two 1,5V batteries, type R6 (RL6) micro. We recommend using alkaline batteries. Be careful to

correctly insert the batteries into the battery compartment (observe the drawing on the compartment

bottom). Check the batteries every now and then to prevent the leakage of worn out batteries.

In order to assure perfect functioning, the remote control handset should be always pointing toward the

TV set. The flashing of the red signal light indicates, that the TV set is receiving the infra-red signals.!

! Signal light

# P

% V

& V

' Analogue select (Video and Audio)

( Mains switch

) Headphone socket (3,5 mm)

* Power suppply cord

+ Aerial socket

, SCART 2 socket

- SCART 1 socket

. SVHS input connector

/ VIDEO input connector

0 AUDIO L input connector

1 AUDIO R input connector

Stand-by indicator

Infrared receiver

rogramme- / Switching on the set

from stand-by mode

Programme+ / Switching on the set

from stand-by mode

olume- / Analogue functions-

olume+ / Analogue functions+

CONTROL UNIT PANEL

Using tke keys on the control unit which is located in the lower part on the front side of TV set, it is

possible to set all the important functions of it.

! " # $ % & ' (

*) +

, -

SWITCHING ON AND OFF

SWITCHING ON TO

STAND-BY MODE

Switch on the TV set to stand-by mode by

pressing the mains switch (. The red indicator

light ! turns on.

SWITCHING ON FROM

STAND-BY MODE

When switching on, the red indicator turns

green.

The time between switching on and picture

appearing on the TV set is 4 to 8 seconds.

If your TV set is in stand-by mode, you can

switch it on with one of the following

procedures:

• press the key ª  on the remote control,

• press the Pr- # or Pr+ $ key on the control

unit,

• press any of the programme selection keys

1-0  on the remote control.

With the first two procedures the TV set will turn

on and the programme selected will be the

programme stored under 1. With the thirth

procedure, the TV set will turn on to programme

entered by pressing any of the numbers on the

keys 1-0 .

If the programme number has one digit, press

the key with adequate number (e.g. 2) and after

two seconds the displayed number disappears -

the programme displayed is the programme

under number 2.

If the programme number has two digits (e.g.

15), two keys (1 and 5) shall be pressed

consequently, the time elapsed between

pressing both numbers should not exceed 2

seconds - the programme displayed is the

programme under number 15.

If you select programme number which is not

stored, the "EMPTY" sign will be displayed.

In the AV mode (AV1, AV2 or SVHS) you can

switch on your TV set by pressing the AV  key.

If AV signal is connected (socket 8 on SCART

connector), the TV set switches over to AV mode

automatically. This is for programmes received

via Euro-AV input (SCART) on the rear side of the

TV set.

To exit AV mode, simply press the key › ¢.

SWITCHING OFF TO

STAND-BY MODE

Switch the TV set from operation mode to stand-

by mode by pressing key ª . The green control

light turns red. The power consumption is

reduced to app. 0,5 W.

If there is no programme on the channel that

your TV set is set to, the TV set will turn off after

5 minutes.

You can also select and set other switch-off time

(see SPECIAL-SLEEP TIMER menu).

In all above stated examples the TV set turns off

to stand-by mode.

If you don't intend to watch TV for a longer period of time (e.g. over the night - switch it off

with the mains switch (!

SETTING TV PROGRAMMES

When switching on the TV set for the first time or

if you want to change programme settings, use

the MENU key  and move to "MENU". From

this menu you can move to the following menu:

• INSTALLATION

• SPECIAL

• ZOOM (see page 12)

In "MENU" you can select between stated

menus with the p and q keys. The

selected menu is always illuminated. To switch

on the selected menu use the t or u keys.

Use the p, t, u and q keys in the

same way in every menu.

MENU "INSTALLATION"

searching the flashing "..." sign is displayed near

the "AUTOSTORE". If you want to interrupt

searching, press key STOP  on the remote

control.

When searching is finished, the TV channels

which were found are automatically sorted and

stored. For identified programmes their name is

displayed, while others are marked wit a letter P

and successive number. When finished, the TV

set returns to "INFO" menu. You can also return

to this menu at any time by interrupting the

automatic search.

To exit the "INFO" menu, press the key › ¢.

Return to "INSTALLATION" menu via

"MENU". In "INSTALLATION" menu the

channels can be manually searched. Use it if you

want to find a channel with very weak signal or

simply if you want to find another programme

without activating automatic search. Use the

p or q keys and illuminate selection

"PROGRAM NR". Use the use the t or u

keys and select the programme location, where

you want to store your programme.

Use the p and q keys and illumunate

selection "CHANNEL". Channel can be set

using one of the following procedures. Use the

t or u keys and select the previous or the

next channel or simply enter the number of the

channel. Use the OK  key and move to the S

range or back.

If the signal of the selected channel is very weak

you can improve it as follows: use the p and

q keys and illuminate the "FINE TUNING"

selection and set the optimum value with the

t and u keys.

If you want to store modifications, move to the

"STORE" selection. Use the t or u keys

and activate storing procedure. The "STORE"

To exit the "INSTALLATION" menu, press the

key › ¢.

INSTALLATION

AUTOSTORE >>

PROGRAM NR. 04

CHANNEL C12

FINE TUNE

STORE < >

This menu is used for searching, sorting and

storing of programmes.

Move to selection "AUTOSTORE" with keys

p or q.

When "AUTOSTORE" is illuminated use the key

u to start automatic channel searching

through the entire frequency range VHS, UHF

and S. By pressing the same key once again, the

"AUTOSTORE" sign is displayed. Confirm

searching by pressing the key OK . During

INSTALLATION >

SPECIAL >

ZOOM >

MENU "INFO"

When automatic search, classifying and storing

of channels is finished, you automatically move

to the "INFO" menu of set programmes. For

direct entry into this menu, press the key i .

If you don't like the way programmes are sorted,

you can arrange programmes in this menu, as

follows:

NAME

(to name or rename a selected programme)

• If you want to rename the required

programme, press the blue key  - on the

right side the first character of the title is

squared and marked with inverted colour.

• Use the p and q keys and select various

characters, letters and figures.

• Use the t and u keys, move to the next

character and select it as previous one.

• Repeat the procedure until the programme is

renamed.

Press the blue key once again and confirm the

renaming procedure. To exit the "INFO" menu,

press the key › ¢.

MENU "SPECIAL"

From the "MENU" (key MENU ) you can

enter the "SPECIAL" menu. When in

"SPECIAL", use the p and q keys and

select one of the six functions. To activate or

deactivate the functions, use the t and u

keys.

SPECIAL

LANGUAGE ENG

PERM. OSD OFF

SLEEP TIMER OFF

CHILD LOCK OFF

VIDEO OUT ON

INFO

01 TF1

NAME

11 P11 ..

02 M6 12 P12 ..

03 TV5 13 P13 ..

04 P04 .. ... ..

.. ... .. ... ..

DELETE

01 TF1

END

INSERT

(to insert a programme on a specific location)

• Use the p, t, u and q keys and

select the required programme - the

programme is highlighted white on the right

bottom part of the display.

• Use the green key  and mark the

programme - the programme is highlighted

green the right bottom part of the display.

• Use the p and q keys and move to the

position where you want your programmes to

be stored - the programme is highlighted in

red.

• Use the green key  and activate inserting of

the selected programme.

DELETE

(to delete selected programme)

• Use the p, t, u and q keys and

select the required programme - the

programme is highlighted white on the right

bottom part of the display.

• Use the yellow key  and delete the

programme - the programme is highlighted

yellow. Three dots are flashing under the

highlighted programme until the deleting

procedure is finished.

• All programmes arranged bellow the deleted

programme are moved one position forward.

Available functions:

LANGUAGE:

Use the t and u keys and select the

language in menus.

PERM.OSD:

If this function is on, in the top left corner the

programme number will be displayed, or AV sign

if in AV mode.

SLEEP TIMER:

With this function you can preset the time of

switching off. It can be preset from 0 to 120

minutes in 15 minutes intervals.

CHILD LOCK:

With this function you can lock certain

programmes in order to prevent children from

watching them. If the "CHILD LOCK" function

is on, the keys on the remote control and on the

control unit are not active. If you switch off the

locked TV set and then again switch it on, the

"LOCKED" sign will be displayed on the screen.

The same happens when switching over

between programmes. To exit this status, enter

the "SPECIAL" menu and switch off the

"CHILD LOCK" function.

VIDEO OUT:

Some cable programmes (e.g. PREMIERE) are

coded. You can watch these programmes only if

you have encoder. When installing the encoder,

follow this procedure:

• Use the SCART cable cord and connect the

encoder into the AV 1 socket (SCART1).

• Use the t and u keys and select position

"ON".

If you do not use the encoder, the "VIDEO

OUT" function should be in position "OFF".

To assure optimum quality of the picture from

the external units (VCR, satellite receiver...)

equipped with SCART socket, connect the cable

cord to AV1 socket (SCART1). Also in this case

the "VIDEO OUT" function should be in position

"OFF".

MODE STEREO

SPACE ON

STORE < >

SOUND

ADJUSTING PICTURE AND SOUND

Sound can be adjusted either by pressing the

t and u keys on the remote control or §-

% and §+ & keys on the control unit. Picture

and volume are adjusted in two menus:

• PICTURE

• SOUND Ç

MENU "PICTURE"

Enter the "PICTURE" menu by pressing the

PICT  key. Four parameters can be set in this

menu:

• BRIGHTNESS

• CONTRAST

• COLOUR SATURATION

• SHARPNESS

• HUE

Hue adjustment is present only in AV mode with

NTSC signal.

Use the p and q keys and move between

these selections. To increase or decrease the

value use the t and u keys.

In this menu you can switch between three

preset settings of colour temperatures "TINT":

• WARM - red tone prevails,

• NORMAL,

• COLD - blue tone prevails.

The required modifications can be stored with

the t and u keys, but first you have to

move to the "STORE" position. During storing,

the "STORE" sign flashes in red.

MENU "SOUND Ç"

Press the SOUND key  and switch on the

"SOUND Ç" menu. Within this menu, you can

optionally set values for the following sound

functions:

• VOLUME,

• BALANCE,

• BASS,

• TREBLE.

To move up and down these positions use the

p or q keys. The desired values of these

positions are set with the t and u keys. In

"MODE" you can switch between four modes:

• DUAL A,·

• DUAL B,

• MONO,

• STEREO.

If you want to switch over among these

functions, the programme should be transmitted

in dual tone or stereo mode.

In the "SPACE" mode, you can switch on/off the

panorama effect.

The required modifications can be stored with

the t and u keys, but first you have to

move to the "STORE" position. During storing,

the "STORE" sign flashes in red.

To exit this menu, press the key › ¢.

PICTURE

TINT NORMAL

STORE < >

SOUND OFF

Press the key Ï  on the remote control and

turn off the sound - the sign Ï is displayed on the

screen. Press the same key once again and turn

on the sound. To turn the sound on again, you

can also use the t and u keys on the

remote control or the §- % and §+ & keys on

the control unit. By holding these keys pressed,

the volume will continuously increase or

decrease, starting at the value set before turning

the sound off.

HEADPHONE SOCKET

You can connect headphones to stereo

headphone socket. To this socket you can

connect stereo headphones with min.

impedance 8 Ohm and 3,5 mm plug. If the plug

of your headphones is different use an adequate

adapter. Set the volume wit keys on remote

control and control unit panel.

When you switch off the headphones,

loudspeakers automatically switch on.

RECALLING THE STORED VALUES

To recall the stored values of picture and sound

press the N ¤ key. The "PERSONAL" sign

appears on the left of the screen. By pressing the

N ¤ key once again within 5 seconds the "DAY"

(picture pre-set daily) sign appears on the left

side of the screen. By pressing the N ¤ key once

again within 5 seconds the "NIGHT" (night

adjustment) sign appears on the left side of the

screen (brighter or darker picture).

By pressing the N ¤ key once again the stored

values "PERSONAL" are restored. Any

modifications of the picture or sound, which are

adjusted in the menu, shall be stored in

"PERSONAL". "DAY" and "NIGHT" are pre-

set in the factory and cannot be modified.

EURO-AV INPUT - SCART

Any of the video devices with a video output

(VCR, videocamera, satellite receiver,

computer...) can be connected to the SCART

socket. If AV signal is connected (terminal pin 8

on SCART connector) the TV set is automatically

switched over to AV mode, when an external

device is connected. If there is no AV signal ,

successively press the AV  key and move up or

down the following ranges:

• AV key - first press : AV1 (SCART 1),

• AV key - second press : AV2 (SCART2),

• AV key - third press : YUV (Component

input Y, Cb, Cr)

• AV key - fourth press : S-VIDEO (Mini DIN,

AUDIO L, AUDIO R),

• AV key - fifth press : AV3 (CINCH INPUT

VIDEO, AUDIOL, AUDIO R),

• AV key - sixth press : TV mode, (antenna).

Return to TV mode by pressing the key › ¢.

If you want to record a certain program on VCR,

activate the "VIDEO OUT" function in the

"SPECIAL" menu in the position "ON"!

With consequent pressing of ZOOM ¡ key you can switch between five format:

PICTURE FORMAT 16 : 9

When receiver decodes the signal in format 16:9, it will automatically switch to picture 16:9!

Between above mentioned formats you can switch also with menu

"ZOOM".

You can reach "ZOOM" menu through the "MENU" menu with

following keys p, t, u and q.

Menu "ZOOM" includes five different selections. Between

selections you switch keys t or u:

INSTALLATION >

SPECIAL >

ZOOM >

ZOOM

ASPECT RATIO 4:3

ZOOM

ASPECT RATIO ZOOM2W

ZOOM

ASPECT RATIO 16:9

ZOOM

ASPECT RATIO ZOOM1

SETTINGS NORMAL

STORE < >

ZOOM

ASPECT RATIO ZOOM2

SETTINGS USER

ZOOM

SCROLL

STORE < >

ASPECT RATIO 4:3, 16:9 and ZOOM 1 you not change!

Selections ZOOM 2 and ZOOM 3 include two settings: • NORMAL - manufacturer settings

• USER - adjust on your desires

Adjustment user "USER" in menu "ZOOM" - "ASPECT RATIO": "ZOOM 2" or "ZOOM 3" you can

change in two ways:

• with key p or q you can select ZOOM

• with key t or u you can proportionally minimize

or maximize the picture horizontally or vertically

• with key p or q you can select SCROLL

• with key t or u you can move the picture

up and down

You can save the change of picture format in selection "USER" with moving on selection "STORE".

Using keys t or u you activate storing procedure. The "STORE" sign in the menu flashes in red for

a second.

To exit the menu you press key › ¢.

Notice:

Recall of manufactures setting in "ZOOM 2" or "ZOOM 3" you can reach if you move to selection

"SETTINGS" and with keys t or u select "NORMAL". You can start storing procedure with

selection "STORE" and using keys t or u.

ZOOM:

SCROLL:

ZOOM SCROLL

INPUT

SIGNAL

(FORMAT)

MENU:

ASPECT RATIO:

4 : 3

16 : 9

LETTER BOX

16 : 9

WIDE

1,85 : 1

ZOOM 1

ZOOM 2

ZOOM 3

16 : 9

TELETEXT

To display teletext information on the screen, a

high quality signal is required, without any

reflections, otherwise the teletext display is of

low quality and it may have many mistakes.

Legibility is poor and the display of current day

time may be interrupted or incorrect. In some

cases the teletext receiving can be improved

with fine adjustment on the channel in the

"INSTALLATION" menu.

CURRENT DAY TIME

While you are watching TV, you can press the key

ˆ £ and in the upper right corner of the screen

the current day time will be displayed. If there is

no teletext signal for the programme you are

watching, the current day time is not displayed.

TELETEXT ON/OFF

Press the key †  and switch on the teletext.

The picture on the screen disappears but the

tone remains unchanged. On the black

background the page 100 is displayed - this is the

index page containing the information on

teletext for the programme you are currently

watching.

Switch off teletext by pressing the key › ¢.

Teletext can be switched on also when the TV set

is in AV mode.

PAGE SELECTION

Tune in to page 100. The three digit number

indicates the number of page where certain

information is located. To select the required

number of page, use the numeric keypad on the

remote control 1-0 , and enter the three

numbers one after another. The entered number

is displayed in the first line, in white. After

entering the last (third) number, the counter

turns green and starts to count toward the newly

selected number. When reaching the selected

page, the counter turns white and selected

number is displayed. You can select optional

number of teletext information. Don't forget that

some pages are not transmitted, so the counter

cannot stop on those pages.

LISTING UP (Page+)

Press the key p and increase the number of

pages for one, which means that you return to

the following page.

LISTING DOWN (Page+)

Press the key q and decrease the number of

pages for one, which means that you return to

the previous page.

LISTING WITH COLOURED KEYS

In the bottom line the four coloured fields are

displayed. You can use them to speed up listing

through the teletext pages:

• Red field:

With red key  the number of pages is

decreased by one,

• Green field:

With green key  the number of pages is

increased by one,

• Yellow field:

With yellow key  the number of pages is

increased to the first ten or to the first full

page following it.

• Blue field:

With blue key  the number of pages is

increased to the first hundred or to the first

full page following it.

SUBPAGES SELECTION

Some of the pages contain more information

than can be shown on one screen. Therefore the

contents of the page is divided in two or more

subpages which are displayed on the screen in

turns. Number 1/9 means that the first subpage

of nine is displayed. Use the STOP key  to stop

the cycling. If cycling of subpages is interrupted,

in the top left corner of the screen the STOP sign

is displayed. To continue with cycling, press the

STOP key  once again.

If you want to see one specific subpage (say 3),

select it with the following procedure:

• Press key ˆ £ on the lower screen part the

number of page and subpage is displayed

(e.g. 358-0001),

• you want to select subpage number 3 - press

0, 0, 0, 3 one after another,

• on the lower screen part the following number

is displayed: 358 - 0003,

• when you finish with the selection, you usually

have to wait for few seconds or even minutes

for the TV studio to send the requested

subpage.

You can also use the Listing Up/Down function

to enter the subpage.

MIX TT/TV, TEXT OFF

Consequently press the key †  to set:

• teletext on,

• mix TT/TV,

• teletext off.

In Mix TT/TV mode the teletext is displayed over

the TV picture. You can simultaneously watch

the programme and read the teletext.

In the Text Off mode watch the TV programme

while you are waiting for the TV studio to send

the required page, but you cannot switch over

between programmes. When teletext receives

the required page or subpage, the number of

page or subpage is displayed. If you press the

key †  once again, the text of the required

page or subpage is displayed on the screen.

DOUBLE TEXT HEIGHT

If you find the teletext hard to read, you can

enlarge the text by pressing the ZOOM key ¡.

The screen will display the enlarged text of the

upper half of the teletext page. Pressing the

ZOOM key ¡ once again will display the other

half of the enlarged text and by pressing the

ZOOM ¡ key once again, the text will return to

normal size.

HIDDEN PART OF THE TEXT

Certain text on the teletext has hidden

information (quiz, riddles, VPS...). Press the N ¤

key and reveal the text. To hide the text once

again, simply press the N ¤ key.

100 TTX TV .............

DFGRTJOHZRTZOPHZOPJKGZKOJKOGZJOPZDJKOGHKOJKOGHJ

KOGHJKOHJKOHJOKGHJLGHNMKOGHDNMKOGHMODGHNOGHGJ

JHJHJHJHJHJJHJHJHJHJNGFZRTFGRFMODHJM

MOPOPHIOPDFGHJOFGHHPFGNMOFGNMODFGHMOPNMPVBNMP

FGIPHVHMINMIPFGHMIGFMIPNHMIPGHIPMGHMJIOPDGHJMIOPG

HJGHJKOPFTOPHOPFGJOPTJOHOJFGHOJKDFZJIJFPGHJFGJOHF

TJIPHJIOPFGHJIRTJIHJIFGHJIDTJIHJIFGHITSDRIZJIFTHJISDFGJIH

JIFGHJITJIZJIFGHJITJZJIFGJHJIGHZJIFGJIHJIDFGJIFGHJTJHZJFG

HJJIFGHJIDFGJIOHJDFGJIHJVGJIOTJFGJFGDJFGHJIFGHJFGJOHJ

FTDHJDFGJOHJOPHJOFGHOPJJHDFGJOHJOFGHJOPFGJPHJFGJ

OPHJOPGHJOPFGJFHOFJOJGHJFZJUUKHJKJKLHJKJLGHKHKGHJ

KGHJFKHJKHJKFGHJKFKFGHKGHKHJFKHJKJKJKJLJHLKJLHJKL

100 TTX TV .............

DFGRTJOHZRTZOPHZOPJKGZKOJKOGZJOPZDJKOGHKOJKOGHJ

KOGHJKOHJKOHJOKGHJLGHNMKOGHDNMKOGHMODGHNOGHGJ

JHJHJHJHJHJJHJHJHJHJNGFZRTFGRFMODHJM

MOPOPHIOPDFGHJOFGHHPFGNMOFGNMODFGHMOPNMPVBNMP

FGIPHVHMINMIPFGHMIGFMIPNHMIPGHIPMGHMJIOPDGHJMIOPG

HJGHJKOPFTOPHOPFGJOPTJOHOJFGHOJKDFZJIJFPGHJFGJOHF

TJIPHJIOPFGHJIRTJIHJIFGHJIDTJIHJIFGHITSDRIZJIFTHJISDFGJIH

JIFGHJITJIZJIFGHJITJZJIFGJHJIGHZJIFGJIHJIDFGJIFGHJTJHZJFG

HJJIFGHJIDFGJIOHJDFGJIHJVGJIOTJFGJFGDJFGHJIFGHJFGJOHJ

FTDHJDFGJOHJOPHJOFGHOPJJHDFGJOHJOFGHJOPFGJPHJFGJ

OPHJOPGHJOPFGJFHOFJOJGHJFZJUUKHJKJKLHJKJLGHKHKGHJ

KGHJFKHJKHJKFGHJKFKFGHKGHKHJFKHJKJKJKJLJHLKJLHJKL

Mix (TT/TV)Teletext (TT)

DEMAGNETISATION OF THE PICTURE TUBE

Changes of the magnetic field near the TV set may cause picture tube magnetisation and colour spots

may appear on the screen. This can happen if you move the TV set or rotate it with respect to the

direction of magnetic field or if you place a device with magnetic source next to the TV set (loudspeakers,

electric motor).

Demagnetisation procedure is as follows:

Switch off the TV set (with the mains switch), wait for the TV set to cool down (at least 20 minutes) and

then switch it on again.

TROUBLE SHOOTING

Instant and permanent disturbances may occur when receiving the television programme. The failure

may not necessary be in the operation of the TV set. Some disturbances:

• NO SOUND, NO PICTURE

Check the power supply - socket for 230 V.

• POOR QUALITY OF PICTURE AND SOUND

Check antenna connection, fine adjustment of the channel and the direction of the

antenna.

• NOISY PICTURE

Check if antenna system is correctly connected.

• ELECTRICAL INTERFERENCE ON SCREEN, DISTORTED SOUND

Remove devices which cause external interference.

Remote control malfunction.

Check the battery, polarity.

The TV set is microprocessor controlled, and it is possible that it gets blocked. Switch the TV set off

and on.

• NO SOUND

Check the volume.

Press the sound on/off key.

In case there is no sound with the video connection via SCART, check the connection.

SAMPLE

TEAC AUSTRALIA PTY., LTD

HEAD OFFICE

NSW OFFICE

OLD OFFICE

WA OFFICE

SA OFFICE

TEAC CORPORATION Phone: (0422) 52-5081

Phone: (03) 9672 2400

Phone: (02) 8811 4000

Phone: (07) 3010 0100

Phone: (08) 9479 6522

Phone: (08) 8234 1044

TEAC 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550 Japan.

A.B.N. 80 005 408 462.

280 William Street, Melbourne VIC 3000.

Unit 8, 20-22 Foundry Rd., Seven Hilis, NSW 2147.

345 Montague Road. West End, QLD 4101.

273 Grerat Estern Highway, Belmont WA 6104.

Car. Sir D. Bradman & Marion Roads, Cowandillia, SA 5033.

TEAC EU2890ST Owner's manual

Brand: TEAC

Model: EU2890ST

Category: CRT TVs

Type: Owner's manual

Download PDF

report

TEAC EU2890ST Owner's manual

TEAC EU2890ST Owner's manual

Related papers

Other documents