Liebherr EG 1624 Comfort Assembly And Installation Instructions

Type
Assembly And Installation Instructions

This manual is also suitable for

Installation instructions
decor fridges and freezers
20190417
7086358 - 00
EK/ EG
Contents
1 General safety information................................... 2
2 Transporting the appliance................................... 2
3 Installing the appliance......................................... 2
4 Appliance dimensions........................................... 3
5 Recess dimensions............................................... 3
6 Ventilation of the kitchen unit............................... 4
7 Changing over door hinges.................................. 4
8 Decor panel assembly........................................... 4
9 Mount the décor panel with equaliser trim......... 5
10 Installing the appliance in the recess.................. 5
11 Disposing of packaging........................................ 6
12 Connecting the appliance..................................... 6
Illustrated installation instructions...................... 7
The manufacturer works constantly on the further development
of all the types and models. Therefore please understand that
we have to reserve the right to make design, equipment and
technical modifications.
To get to know all the benefits of your new appliance, please
read the information contained in these instructions carefully.
The instructions apply to several models. Differences may
occur. Text relating only to specific appliances is marked with
an asterisk (*).
Instructions for action are marked with a , the results of
action are marked with a .
1 General safety information
-
Only install, connect and dispose of the appli-
ance according to the instructions. Take
particular note of “Recess dimensions” (see 5)
and “Ventilation of the kitchen unit” (see 6) .
-
The socket must be easily accessible so that
the appliance can be quickly disconnected
from the supply in an emergency. It must be
outside the area of the rear of the appliance.
DANGER identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note identifies useful information and tips.
2 Transporting the appliance
CAUTION
Risk of injury and danger of damage as a result of incorrect
transport!
u
Transport the appliance in a packed condition.
u
Transport the appliance upright.
u
Do not transport the appliance without assistance.
3 Installing the appliance
WARNING
Risk of fire due to short circuit!
If the mains cable/connector of the appliance or of another
appliance touch the rear of the appliance, the mains cable/
connector may be damaged by the appliance vibrations,
leading to a short circuit.
u
Stand the appliance so that it is not touched by connectors
or main cables.
u
Do not plug the appliance or any others into sockets located
near the rear of the appliance.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u
The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
u
Only use the appliance when it is installed.
WARNING
Fire hazard due to refrigerant!
The coolant used is eco-friendly but also flammable. Any
leaking coolant may ignite.
u
Do not damage the piping of the refrigeration circuit.
WARNING
Fire hazard and danger of damage!
u
Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
WARNING
Blocked ventilation openings pose a risk of fire and damage!
u
Always keep the ventilation openings clear. Always ensure
that the appliance is properly ventilated!
If your appliance is not a side-by-side (SBS) appliance:*
NOTICE
Risk of damage due to condensate!
u
Do not install the appliance directly alongside a further
refrigerator/freezer.
General safety information
2 * Depending on model and options
NOTICE
Risk of damage due to condensation!*
When stacking multiple appliances there is a risk of conden-
sation damage.
Your EG.. up to a height of 880 mm is fitted with an overhead
heating system.
u
Do not stack refrigerators or freezers unless the bottom
appliance is your Liebherr-EG... model up to a height of 880
mm.
q
In the event that the appliance is damaged, contact the
supplier immediately before connecting to the mains.
q
The floor at the site must be flat and level.
q
Do not install the appliance in a location where it is exposed
to direct radiation of the sun, next to a cooker, heater and
similar.
q
Do not install the appliance without assistance.
q
The more coolant there is in the appliance, the larger the
room in which the appliance is installed must be. If the room
is too small, any leak may create a flammable mixture of gas
and air. For each 8 g of coolant the installation space must
be at least 1 m
3
. Information on the coolant is on the model
plate inside the appliance.
q
Fit the appliance in stable kitchen units only.
q
The following ventilation gaps must be observed:
The depth of the ventilation channel at the rear of the unit
must be at least 38 mm.
At least 200 cm
2
is required for the ventilation gap cross
sections in the plinth and the housing cabinet.
Basically the principle applies: the larger the ventilation
space, the more energy-saving the appliance is in opera-
tion.
u
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u
Remove the protective film from the decorative trims.
u
Remove all transit supports.
u
Dispose of packaging material (see 11) .
Note
u
Clean the appliance .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u
Always see to good ventilation at the installation site.
4 Appliance dimensions
Fig. 1
A (mm) B (mm) C (mm) D (mm) E (mm)
EK 16..,
EG 16..
559 872 540 595 888
EK 23.. 559 1218 540 595 1232
5 Recess dimensions
The appliance is built-in and therefore completely enclosed by
a kitchen unit. The kitchen unit concerned must be built exactly
to the prescribed dimensions and allow for sufficient ventilation,
both at air inlet and outlet, to ensure proper appliance opera-
tion.
Fig. 2
Appliance dimensions
* Depending on model and options 3
F
(mm
)
G
(mm
)
H (mm) J
(mm
)
K
(mm
)
L
(mm
)
EK 16..,
EG 16..
874
880
560
570
min. 550,
560 recom-
mended
min.
500
min.
40
max.
19
EK 23.. 1220
1226
The specified energy consumption applies to a unit depth of
560 mm. The appliance will work properly at a unit depth of 550
mm, but at a slightly higher energy consumption.
u
Check the wall thickness of the adjoining units: the walls
must be at least 16 mm thick.
u
Only install the appliance in robust, stable kitchen units.
Secure the units against tipping.
u
Align the kitchen unit using a spirit level and marking square
and if necessary compensate with shims.
u
Ensure that the floor and walls of the unit are at right angles
to one another.
6 Ventilation of the kitchen unit
Fig. 3
-
There must be an effective ventilation shaft of at least
200 cm
2
per appliance at the air inlet
Fig. 3 (A)
and outlet
Fig. 3 (B)
vent.
-
The principle applies that the larger the ventilation shaft, the
more energy-saving the operation of the appliance.
-
The depth of the ventilation shaft at the back of the unit must
be at least 38 mm.
Fig. 4
-
The upper ventilation shaft can either be positioned directly
above the appliance with an optional ventilation grille
Fig. 4 (C)
, close to the ceiling above the unit
Fig. 4 (D)
or as
an air outlet opening in a false ceiling
Fig. 4 (E)
.
7 Changing over door hinges
WARNING
Risk of injury through door dropping out!
If the fastening components are not screwed in tightly enough,
the door may drop out. This can lead to serious injury. What is
more, the door may also not close fully, so that the appliance
may not refrigerate properly.
u
Screw the bottom and top turn hinges tightly into place (with
4 Nm).
There is a risk of injury during this stage! Please
observe the safety instructions!
The instructions apply to several models. Only carry
out this step if it is relevant for your appliance.
Choose between the alternatives given.
Loosen the screws only, do not undo them all the way.
Check the screws and tighten if necessary.
u
While changing over the door hinges, observe the safety
instructions above and also the information in the symbols
key.
Change the hinges over as shown at the end
of the book.
8 Decor panel assembly
Using a décor frame and decor panel, the appliances can be
matched or contrasted in colour to the kitchen units.
Ventilation of the kitchen unit
4 * Depending on model and options
Decor panel dimen-
sions(mm)
Max.
decor
panel
weight
(kg)
Recess height Height Width Maximu
m thick-
ness
874 — 880 860 585 4 5
1220 — 1226 1206 585 4 7
Décor frames are available from Customer Services as acces-
sories in the following additional colours:
brown: 9911350 white: 9911348 aluminium
coloured: 9911346
u
For thicker décor panels
Fig. 5 (2)
, reduce thick-
ness to a maximum 4 mm
as illustrated.
Fig. 5
u
Unscrew the décor
frame
Fig. 6 (1)
at the
top.
u
Just loosen the
screws of all the other
decor frames
Fig. 6 (3, 4)
and slide
the decor frames
forwards.
u
Slide in the decor
panel
Fig. 6 (2)
.
u
Push back the décor
frame
Fig. 6 (3, 4)
and screw tightly into
place.
u
Screw the décor
frame
Fig. 6 (1)
back
tightly into place at
the top.
u
Screw on the handle
Fig. 6 (5)
.
u
Snap the caps
Fig. 6 (6)
onto all the
screw heads.
Fig. 6
9 Mount the décor panel with
equaliser trim
If there is already a décor panel present, but the panel is not
high enough, it can be adjusted with equaliser trims
Fig. 7 (7)
in
various heights.
One (top only or bottom only) or two (top and bottom) equaliser
trims can be used. Equaliser trims are available from Customer
Services as accessories.
Height of equaliser
trim [mm] h
brown white aluminium
coloured
16 9733032 9733035 9733050
41 9733033 9733036 9733051
60 9733034 9733037 9733052
u
Unscrew décor frame
Fig. 7 (1, 4)
top and
bottom.
u
Just loosen the
screws of all the other
decor frames
Fig. 7 (3)
and slide
the decor frames
forwards.
u
Slide in the decor
panel
Fig. 7 (2)
.
u
Attach equaliser trim
Fig. 7 (7)
to bottom or
top.
u
Place décor frame
Fig. 7 (1, 4)
over the
trims and screw
tightly into place.
u
Push back the décor
frame
Fig. 7 (3)
and
screw tightly into
place.
u
Screw on the handle
Fig. 7 (5)
.
u
Snap the caps
Fig. 7 (6)
onto all the
screw heads.
Fig. 7
10 Installing the appliance in the
recess
WARNING
Fire hazard from short-circuiting!
u
When pushing the appliance into the recess, take care not to
crush, jam or damage the mains power cable.
u
Do not operate the appliance with a defective mains power
cable.
There is a risk of injury during this stage! Please
observe the safety instructions!
The instructions apply to several models. Only carry
out this step if the appliance is equipped with the
corresponding feature.
Choose between the alternatives given.
Loosen the screws only, do not undo them all the way.
Check the screws and tighten if necessary.
u
Please take note of the information in the symbols key
during installation.
Install the appliance into the recess as shown
at the end of the book.
Mount the décor panel with equaliser trim
* Depending on model and options 5
11 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film!
u
Do not allow children to play with packing material.
The packaging is made of recyclable materials:
-
corrugated board/cardboard
-
expanded polystyrene parts
-
polythene bags and sheets
-
polypropylene straps
-
nailed wooden frame with polyethylene panel*
u
Take the packaging material to an official collecting point.
12 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
u
Do not use a standalone inverter.
u
Do not use an energy saving plug.
WARNING
Failure to connect properly
Fire hazard.
u
Do not use an extension cable.
u
Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate .
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u
Check the electrical connection.
u
Plug in the power plug.
Disposing of packaging
6 * Depending on model and options
* Depending on model and options 7
8 * Depending on model and options
* Depending on model and options 9
10 * Depending on model and options
* Depending on model and options 11
Liebherr-Hausgeräte Ochsenhausen GmbH
Memminger Straße 77-79
88416 Ochsenhausen
Deutschland
home.liebherr.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Liebherr EG 1624 Comfort Assembly And Installation Instructions

Type
Assembly And Installation Instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI