JET — Adjustable Swing Away Safety Shield Owner's manual

Brand: JET

Model: — Adjustable Swing Away Safety Shield

Type: Owner's manual

This manual is also suitable for

Adjustable Swing Away Safety Shield

JET — Adjustable Swing Away Safety Shield

The JET Adjustable Swing Away Safety Shield is a must-have accessory for any drill press or milling machine. This shield provides superior protection from flying chips and debris, ensuring your safety while operating your machine. Its adjustable design allows for easy positioning, accommodating various workpiece sizes and shapes.

With its durable construction and heavy-duty materials, the shield withstands the rigors of everyday use in demanding workshop environments. The transparent material offers excellent visibility, allowing you to monitor your work progress without compromising safety.

JET — Adjustable Swing Away Safety Shield

Assembly Instructions and Parts Breakdown

A635 Safety Shield

Assembly

To mount Safety Shield to your JET drill press or

milling machine, proceed as follows.

(Numbers in parentheses refer to index numbers in

Figure 1 and exploded view. Refer to exploded view

on reverse side if clarification is needed.)

1. If there are no existing mounting holes on your

machine, drill two threaded holes at least 1/2 in.

deep in left side of machine headstock. [If you

are using the provided M8 socket head screws

(#14), drill M8-1.25 holes.] Use bracket (#7) as

template for hole pattern.

NOTE: Make sure bracket location will allow

shield to clear front of headstock.

2. Install bracket assembly (#7) to headstock with

two M8X20 socket head screws (#14).

3. Install support arm (#11) and secure with hex

nut and spring washer (#12/13).

4. Install lower bracket bar (#9) and secure with

hex nut and flat washer.

5. Mount shield (#8) to lower bracket bar (#9)

using two socket head screws (#10) and flat

washers (#17).

6. Install limit switch (#18) if desired. (Wiring

connections must be made by qualified

electrician.)

Adjustments

Loosen lock handle (5) to adjust vertical positioning

of shield. Tighten lock handle before operating

machine.

Loosen knob (15) to adjust horizontal positioning of

shield. Tighten knob before operating machine.

Figure 1

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-A635

Ph.: 800-274-6848 Edition 1 12/2015

To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00

p.m. CST. Having the Model Number of your product available when you call will allow us to serve you quickly

and accurately.

Non-proprietary parts, such as fasteners, can usually be found at local hardware stores or may be ordered from

JET.

A635 Safety Shield Assembly – Parts List

Index No. Part No. Description Size Qty

.................. A635 .......................... Safety Shield Assembly (# 1 thru 19) ...................... ........................................

1 ................ 6293347 .................... Spring Pin ................................................................ 3 x 16 mm ..................... 1

2 ................ 32106A-2................... Support Bracket Bar ................................................ ...................................... 1

3 ................ 32106A-3................... Bushing .................................................................... ...................................... 1

4 ................ 32106A-4................... Spacer ..................................................................... ...................................... 1

5 ................ 32106A-5................... Lock Handle ............................................................. M6x20 ........................... 1

6 ................ 32106A-6................... C-Clip ....................................................................... S30................................ 1

7 ................ 32106A-7................... Bracket..................................................................... ...................................... 1

8 ................ 32106A-8................... Safety Shield............................................................ 530 x 210mm ................ 1

9 ................ 32106A-9................... Lower Bracket Bar ................................................... ...................................... 1

10 .............. TS-1504021 .............. Hex Socket Head Cap Screw .................................. M8-1.25 x 12 ................. 2

11 .............. 32106A-11................. Support Arm............................................................. ...................................... 1

12 .............. TS-0570031 .............. Hex Nut .................................................................... 3/8”-16........................... 2

13 .............. TS-0720091 .............. Spring Washer ......................................................... 3/8” ................................ 2

14 .............. TS-1504041 .............. Hex Socket Head Cap Screw .................................. M8 x 20 ......................... 2

15 .............. 32106A-16................. Lock Bolt with Knob ................................................. M8 ................................. 1

16 .............. 32106A-17................. Spacer ..................................................................... ...................................... 1

17 .............. TS-1550061 .............. Flat Washer ............................................................. 8mm .............................. 2

18 .............. A635-18..................... Limit Switch.............................................................. ...................................... 1

19 .............. TS-2284202 .............. Phillips Head Screw ................................................. M4x20 ........................... 2