Sena PRISM TUBE Quick start guide

Brand: Sena

Model: PRISM TUBE

Category: Dashcam

Type: Quick start guide

Sena PRISM TUBE is an action camera specifically designed for motorcycle helmets, offering a range of features to enhance your riding experience. With its compact size and aerodynamic design, it seamlessly integrates with your helmet without compromising comfort or safety. Here are some of its key capabilities:

High-quality video recording: Capture stunning videos in 1080p resolution at 30 frames per second, ensuring crisp and detailed footage.
Loop recording: Activate loop recording to continuously record your journey, overwriting the oldest footage when the memory card is full.
Easy operation: Navigate through the camera's functions effortlessly using the intuitive buttons and LED indicators.

High-quality video recording: Capture stunning videos in 1080p resolution at 30 frames per second, ensuring crisp and detailed footage.
Loop recording: Activate loop recording to continuously record your journey, overwriting the oldest footage when the memory card is full.
Easy operation: Navigate through the camera's functions effortlessly using the intuitive buttons and LED indicators.

PREPARATION

Getting to Know the Prism Tube Layout

Camera

Lens Cap

Lens

Slide Switch

SD Card Format Button

DC Power Charging &

Firmware Upgrade Port

Status LED

Rear Cap

Fault Reset

Pin-hole Button

MicroSD Card

Slot

Speaker and Microphone

Speaker

Wired

Microphone

Hook and Loop

Fastener for Speaker

Rear Cap for USB Cable

USB Cable for Speaker &

Microphone

Hook and Loop Fastener

for Wired Microphone

Installing the Prism Tube System

Connecting the Speaker

1 42 3

Note Connect the speaker cable to the USB cable’s black connector.

Mounting

Clamp Unit Camera

BASIC OPERATION

Turning the Camera On or O

ON OFF

“Camera on”, “Recording” “Camera o”

Note • Recording will start shortly after the camera is turned on. Recording stops

shortly before the camera is turned o.

• A microSD card must be inserted to record video.

Switching Between Normal Recording and Loop Recording

Normal Recording

Loop Recording

While the camera is turned on, press the SD Card Format Button for 1 second to

switch between normal recording mode and loop recording mode.

Note The Blue LED blinks once during normal recording and twice during loop

recording.

Adjusting the Angle Speaker

2 3

Note • The tube swivel mount wheel must be fully tightened after adjusting the

camera angle.

• Make sure the tip of the slide switch faces upwards and is parallel to the

ground.

• You can use the glued surface mounting plate to attach the clamp unit to

the surface of the helmet. Full adhesion is achieved after 24 hours.

Connecting the Wired Microphone

To record your voice more clearly, connect the wired microphone.

Note • Connect the wired microphone cable to the USB cable’s red connector.

• The camera’s internal microphone automatically turns on when the wired

microphone is disconnected.

Others

Clamp Unit Tube Swivel Mount

Glued Surface Mounting Plate USB Power & Data Cable

Allen Wrench

Inserting a MicroSD Card

1 2 3

Note Optional microSD cards up to 32 GB are compatible with the Prism Tube.

Quick Start Guide

Action Camera for Motorcycle Helmet

DATE AND TIME SETTING

To set the date and time of the camera, follow the directions below.

1. Turn o the camera and connect it to your PC via a USB cable.

2. Create a blank text le (.txt) with a name “timeset.txt” in the root folder of the

camera.

3. Disconnect the camera from your PC and restart the camera. The camera will

automatically take the date and time at which the text le was created.

TROUBLESHOOTING

Memory Card

When Memory is Full

Blinking

“Memory is full”

Formatting the Memory Card

To format the memory card, turn on the camera and press and hold the SD Card

Format Button for 5 seconds until the LED alternates red and blue.

Note It is recommended to format the SD Card using this method. If you are

formatting the SD Card using a PC, then set the allocation unit size to 32KB

in FAT32.

Fault Reset

If the Prism Tube is not working properly for any reason, push the pin-hole reset

button located on the back of the camera while it is turned on.

Sena Technologies, Inc.

www.sena.com

Customer Support: support.sena.com

E-mail: [email protected]

16.Dec

You can view other Sena products at the

Sena website: www.sena.com.

BATTERY

Checking the Battery Level

Blinking

70~100%

Blinking

30~70%

Blinking

0~30%

Turn on the camera and check the battery level via the Status LED.

Low Battery Warning

Blinking

“Battery low”

Charging the Battery

Charging

Fully charged

AC adapter

TRANSFER

Transferring Video Files

Note Turn o the camera and connect it to your PC via a USB cable. Your PC

should recognize the camera as a removable device.

FIRMWARE UPGRADE

To install the latest rmware of the camera, follow the directions below.

1. Turn o the camera and connect it to your PC via a USB cable.

2. Download the latest rmware from www.sena.com.

3. Move the downloaded rmware le into the root folder of the camera.

4. Disconnect the camera from your PC and restart the camera. The rmware

will be installed automatically.

Sena PRISM TUBE Quick start guide

Brand: Sena

Model: PRISM TUBE

Category: Dashcam

Type: Quick start guide

High-quality video recording: Capture stunning videos in 1080p resolution at 30 frames per second, ensuring crisp and detailed footage.
Loop recording: Activate loop recording to continuously record your journey, overwriting the oldest footage when the memory card is full.
Easy operation: Navigate through the camera's functions effortlessly using the intuitive buttons and LED indicators.

Download PDF

report

Sena PRISM TUBE Quick start guide

Sena PRISM TUBE Quick start guide

Related papers

Other documents