45TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
FAQs: Frequently Asked Questions
Q: Does this dishwasher require a rinse aid to be used?
A: Rinse aid is strongly recommended to enhance the drying performance of the dishwasher. In order to
be more energy efcient, the hybrid drying system does not use a heating element to assist in drying,
so a rinse aid plays an integral role in the drying process. If a rinse aid is not used, water may remain
on the dishes and the tub. Rinse aid helps to ensure that the majority of the water has been sheeted
off of the dishes at the end of the rinse and that the load is ready for the dry cycle.
Q: What can be done if my dishes have a cloudy, white lm on them after a wash?
A: The cloudy lm is usually caused by minerals in the water reacting with the dishwasher detergent.
First, be certain not to use too much detergent. Refer to Adding Detergent to the Dispenser section
for recommended detergent amounts. Add an extra rinse to the cycle. LG Dishwashers use less
water than traditional dishwashers, so adding an extra rinse aids in rinsing the lm away. If the water
supply is hard, it may be necessary to add a performance booster that addresses the hard water
condition.
Q: What steps can I take to improve drying results?
A: Drying performance is directly affected by the amount of heat that remains in the tub after the
heated rinse is performed. If your dishwasher is far away from your home’s hot water heater, it may
be necessary to run the hot water tap in the sink before starting a wash cycle, to ensure that cool
water is purged from the hot water lines. This will ensure your dishwasher has a consistent supply
of hot water from start to nish. Using the High Temp setting also aids in keeping the inner drum
temperature and dishes hotter before drying begins.
LG dishwashers are designed to be used in conjunction with a rinse aid. Using a rinse aid will
maximize the amount of water that has already been sheeted away from the dishes before the dry
cycle begins. If a rinse aid is used and the performance still needs a boost, adjust the amount of
rinse aid used. 2 is the default setting, but if necessary set the level to 3 so more rinse aid is used.
Water tends to bead rather than sheet off plastic and nonstick surfaces, making them more difcult
to dry. If washing plastic items in a Normal cycle, select the Extra Dry or Night Dry option or both for
better drying results. When the rinse aid is empty, the Extra Dry option is selected automatically.
Allow the dishwasher to completely nish the dry cycle before opening the door. If the door is opened
in the middle of the dry cycle, the heat that is necessary for the hybrid dry system to work will
escape. This will cause all of the dishes inside to remain wet once the cycle nishes.
46 TROUBLESHOOTING
Q: What is the hybrid drying system?
A: The dishwasher does not rely on a heating element for the drying process; instead, it relies on the
heat that is retained by the dishes and the tub during the wash and rinse cycles to turn the moisture
in the tub into humidity.
Warm, moist air in the dishwasher is then pulled into a condensing duct in the door by a fan. The air
then cools, which causes the humidity to condense. Room temperature air is also drawn into the duct
to help the air cool down faster. When this moisture condenses into a liquid, it is drained out.
NOTE
• Rinse aid is required to enhance the drying performance. If no rinse aid is used, water may remain
on the dishes and the tub.
Q: Why am I hearing a whistling sound from the dishwasher?
A: It is important to determine the duration of the noise and when it happens (what part of the cycle).
When water is drawn into the dishwasher, a whistling noise can be heard. This is normal. If the water
pressure is too high, it will be louder, so it may be necessary to adjust the water valve to lower the
pressure if the noise is too loud.
Q: What kinds of dishes can be placed in the dishwasher?
A: Ensure that the dishes you place in the dishwasher are dishwasher safe. Plastic dishware will not
dry as effectively as glass and metal dishware. Plastic items do not retain heat as well as glass and
metal dishware. Plastic cups and dishes may require some hand drying before being put away at the
end of the cycle.
Q: Can I perform a drain only cycle?
A: To drain standing water, press and hold Start for three seconds until the cycle stops. Once the
dishwasher nishes draining, the power turns off.
Q:
Why does my dishwasher continuously chime if I open the door during a cycle or right after
the cycle has nished?
A: This is normal. The dishwasher is letting you know that the interior temperatures of the unit are hot
and to use caution when placing your hands inside. Once the unit has cooled down, the chiming will
stop.
47TROUBLESHOOTING
ENGLISH
Q: What is Control Lock and how is it activated?
A: Control Lock is a feature that prevents the controls from being changed during the cycle. It does
not prevent the door from being opened or the unit from being powered off. To activate or deactivate,
press and hold Half Load and Energy Saver simultaneously for three seconds.
Q: Can I add an extension to the drain hose?
A: If an extension drain hose is required, use
5
/8" or
7
/8" inside diameter, 2-3 ft. length hose and a coupler
for connecting the two hose ends.
Q:
An LED is blinking, the machine is chiming, and the dishwasher won't start. What is wrong
with the dishwasher?
A: This is a safety feature. The door must be closed within four seconds of pressing the Start button.
If the door is not closed within four seconds, an LED ashes, an audible alert sounds, and the
dishwasher does not operate. To start the dishwasher, open the door and either close the door and
press Start (front controls) or press Start and close the door within four seconds (top controls).
Q: Before loading dishes, should I pre-rinse dishes?
A: No, you don't need to pre-rinse the dishes before loading especially if using the Normal and Auto
cycles. The dishwasher washes dishes clean without pre-rinsing.
User Support Videos
For further assistance, there are videos and tutorials available
through the LG.com website.
1
On the www.lg.com/us home page, click on the Support menu
tab to bring up the menu selections. Select Video Tutorials.
2
Select a product category and then pick a topic or search a
keyword.
Scan this QR code to quickly access the
video search page on the LG website.
48 TROUBLESHOOTING
Before Calling for Service
The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems at an
early stage. If the appliance does not function properly or does not function at all, check the following before you
call for service.
Problem Possible Cause Solutions
Dishwasher will not
operate.
Start button is not pressed. • Press the Start button.
Door is not completely closed.
• Make sure that the door is completely
closed and latched.
Power supply or power supply line is
not connected.
• Connect the power supply or power
supply line properly.
Fuse is blown or circuit breaker
tripped.
• Replace the fuse or reset the circuit
breaker.
Dishwasher operates too
long.
Dishwasher is connected to cold water.
• Check the water supply connection or
water heater setting. (Heating cold water
takes longer.)
Odor
The previous cycle was stopped before
completion and residual water remains
in the dishwasher.
• Turn on the power, run the Cancel cycle
option to remove the residual water, then
run the Turbo cycle using detergent but
with the dishwasher empty.
There is food in the bottom of the unit
or in the lter.
• Clean the lter and the interior according
to the Maintenance section of the
owner’s manual.
Unwashed dishes are left in the unit for
a long time.
• Cycle with one cup of white vinegar in a
dishwasher safe glass or bowl placed on
the upper rack. (Vinegar is an acid, and
with constant use it could damage your
appliance.)
Water remains in tub
after completion of cycle.
Drain hose is kinked or clogged. • Adjust hose or clear blockage.
Food soil remains on
dishes.
Improper cycle selection.
• Select correct cycle based on soil level
and type of dishware being washed.
Water temperature is too low.
• Check water supply connection or water
heater setting.
Dishwashing detergent was not used. • Use recommended detergent.
Low inlet water pressure.
• Water pressure should be between 20
and 80 psi.
Water jet holes on spray arms blocked. • Clean the spray arms.
Improper loading of dishes.
• Make sure dishes do not block spray
arm rotation or interfere with detergent
dispenser.
Filters are clogged. • Clean lters.
Cloudiness on
glassware.
Combination of excessive detergent
and hard water.
• Use less detergent and use a rinse aid
to minimize the problem.
Black or gray marks on
dishes.
Aluminum items rubbing dishes during
cycle.
• Reposition the dishes.
Yellow or brown lm
on inside surfaces of
dishwasher.
Coffee or tea stains.
• Eliminate the stain by using a stain
removal product.
49TROUBLESHOOTING
ENGLISH
Problem Possible Cause Solutions
Spots and lming on
dishes.
Low water temperature.
• Water supply should be at least 120 °F
for best wash performance.
Overloading. • Do not overload the dishwasher.
Improper loading. • See the Operation section.
Insufcient water pressure.
• Water pressure should be between 20
and 80 psi.
Insufcient detergent.
• Add the recommended amount of
detergent. See the Operation section.
Rinse aid dispenser is empty. • Rell rinse aid dispenser.
Hard water buildup in the tub.
• Remove all dishes, silverware and
silverware holder from dishwasher.
Only racks should remain in tub. For
best results, use citric acid powder (can
be found in canning sections of most
grocery stores or online). Measure 3
tablespoons (40 g) of citric acid powder.
Fill main wash compartment with
measured powder. If you cannot nd
citric acid powder, pour approximately
one cup (200-300 mL) of white vinegar
into shallow bowl and place in upper
rack. Run Machine Clean cycle. Do not
use detergent.
Noise
Some level of noise is normal during
operation.
• Detergent cover opening.
• Drain pump at the beginning of drain
cycle.
The dishwasher is not level. • Adjust leveling feet.
Nozzle arm knocking against dishes. • Reposition the dishes.
Dishes don’t dry. Rinse agent dispenser empty.
• Check and rell the rinse agent
dispenser if empty.
Lamps do not illuminate. Power is not connected. • Connect power supply.
Spray arms do not rotate
smoothly.
Holes of spray arms are blocked by
food particles.
• Clean the holes of spray arms.
Upper rack is crooked. Rack is poorly adjusted.
• See the Height Adjustable Upper Rack
section.
Dishwasher continuously
chimes when the door
is opened, during or
right after a cycle has
completed.
This is a safety measure. Contact with
escaping steam or the hot contents of
the dishwasher could result in injury.
• Close the door until the dishwasher and
dishes have cooled down. The chiming
will stop if the door is closed or the
interior temperature has cooled.
50 TROUBLESHOOTING
Problem Possible Cause Solutions
Dishwasher chimes if
panel is touched during
operation.
Bumping into or touching the control
panel during operation may result in a
disabled button sound. Only the Power,
Start, and Control Lock buttons are
enabled during operation to prevent
cycle settings from being changed
inadvertently.
• Button sounds can be turned off by
pressing and holding Half Load for three
seconds.
• The end of cycle chime and safety alert
sounds will still sound.
Dishwasher did not nish
cycle.
Door was opened during cycle.
• If the door is opened during a cycle,
the Start key must be pressed within 4
minutes or the machine turns off and all
settings are lost.
Leaking in front of unit Dishwasher not leveled properly.
• Verify the unit is level from side to side
and from front to back. See leveling
instructions in the Installation section.
P1, P2, P3, or P4 appears
in display.
The Download cycle is selected.
• This is not an error code. This code
indicates the current Download cycle.
Error Codes
Problem Possible Cause Solutions
Water inlet problem.
• Check for a clogged, kinked or frozen
water inlet hose.
• Check water supply.
Drainage Problem.
• Check for a clogged, kinked or frozen
water drain hose.
Air gap or disposal is clogged. • Clean air gap or disposal.
Filters are clogged. • Clean Filters.
Water leakage
• Turn off the water supply to the
dishwasher and call an LG Electronics
Customer Information Center at 1-800-
243-0000 (U.S.A.) or 1-888-542-2623
(Canada).
• The dishwasher makes an alert sound
for 10 seconds, and runs the drain pump
intermittently. If power is turned off to
the machine, the machine powers back
on automatically until the AE error is
resolved.
Excessive Water supplied.
• Please call an LG Electronics Customer
Information Center at 1-800-243-0000
(U.S.A.) 1-888-542-2623 (Canada).
Heater circuit failure.
Thermistor failure.
Motor trouble
Vario motor trouble
-
1
-
2
-
3
-
4
-
5
-
6
LG Electronics LDP6797WW User guide
- Category
- Dishwashers
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
LG Electronics LDT5678ST User guide
-
-
LG LDFN3432T Owner's manual
-
-
-
LG 1333029 Owner's manual
-
LG LDP6797WW User manual
-
LG LDT5678ST User manual
-
-
LG Electronics LDPS6762S User manual
Other documents
-
LG SIGNATURE LUDP8908SN User guide
-
-
-
-
LG LDP6797BD Owner's manual
-
-
-
LG STUDIO LSDT9908ST Owner's manual
-
LG LDP7708ST Owner's manual
-
LG LDT7808ST Owner's manual