Expert E200145 User manual

Brand: Expert

Model: E200145

Type: User manual

This manual is also suitable for

NU-E200143-E200144-E200145/1016

6 Rue Gustave Eiffel

91420 MORANGIS- France

http://www.expert-tool.com

E200143 3t

E200144 6t

E200145 12

NU-E200143 E200144 E200145_1016ok.indd 1 24/10/2016 14:33:33

NU-E200143-E200144-E200145_1016

NU-E200143-E200144-E200145/1016

6 Rue Gustave Eiffel

91420 MORANGIS- France

http://www.expert-tool.com

E200143 3t

E200144 6t

E200145 12

F (t) A mm B mm h mm H mm

E200143 3 206 188 288 423 6,4 kg

E200144 6 294 262 400 620 13,7 kg

E200145 12 382 336 500 770 32 kg

(x2

)

E200143 E200144 E200145

3 E200143-3 E200144-3 E200145-3

4 E200143-4 E200144-4 E200145-4

E200143

E200144

E200145

NU-E200143 E200144 E200145_1016ok.indd 2 24/10/2016 14:33:41

Page is loading ...

USER LIABILITY

The owner and/or operator shall have an understanding of the product, its operating characteristics, and safety operating instructions before operating it. Safety

information shall be understood:

- Center load on saddle,

- Do not exceed rated capacity,

- Use only on a hard, level surface,

- Use as a matched pair only,

- Maximum load capacity per matched pair shall not exceed the rated capacity of the individual stand,

- No alterations shall be made to this product,

- Visual inspection shall be made before each use by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts,

- It shall be the responsibility of the employer to ensure that applicable personal protective equipment (PPE) complies with applicable local safety codes,

- Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE UNTIL

REPAIRED OR REPLACED,

- Failure to heed these markings may result in personal injury.

Save these instructions. For your safety and the safety of others around you, read carefully before attempting to assemble, service or use your product. Observe

all safety and warming information. Always wear safety glasses when operating this product. Failure to comply with the information contained within could result

in severe, even fatal injury and/or property damage.

PRODUCT DESCRIPTION

Jack stands are designed to safely support level, rated capacity loads, typically vehicles, for extended periods. Stamped steel construction, ductile iron ratchet

bars to ensure safety, stability. Each comes with a ratchet / collar lock, which prevents inadvertent loss of ratchet bar.

BEFORE USE

1. Inspect stand before each use. Do not use if bent, broken or cracked components are noted. Ensure that all parts move freely.

2. Before using this product, read owner’s manual completely and familiarize yourself thoroughly with the product and the hazards associated with its

improper use.

3. Install ratchet bar into frame with ratchet portion of bar aligned with locking pawl (stopper).

4. Move the ratchet bar to its lowest position by raising the locking handle, thereby releasing the stopper, and guiding the bar downward.

OPERATION

1. Adjust height by pulling up on ratchet bar.

2. The weight of the locking handle should secure the ratchet bar in desired position. To conrm this simply push down on the locking handle.

Check to ensure ratchet is secure before loading.

3. Carefully position stands so that load is centered on stand’s saddle.

4. Slowly lower the vehicle onto the stands.

5. Check to ensure vehicle is secure before working on, around or under. When used to support vehicle, use wheel chocks to prevent inadvertent movement

(B).

TO LOWER LOAD

1. With Suitable Jack, raise vehicle clear of stands.

2. Carefully release stopper and allow ratchet to glide down to lowest position.

3. Carefully remove stands then carefully lower vehicle with lift device.

4. Ensure that all tools, equipment and personnel are clear before lowering load.

MAINTENANCE

Periodically inspect each stand. Ensure all parts move freely . Do not apply oil or grease to any portion of this product. If rust appears, sand affected area and

cover with suitable utility paint.

GUARANTEE: Type D = 2 years. See the general conditions in the EXPERT catalogue or the EXPERT price list.

NU-E200143 E200144 E200145_1016ok.indd 4 24/10/2016 14:33:41

Page is loading ...