Frigidaire DGUS2635LP User manual

Category
Side-by-side fridge-freezers
Type
User manual
TABLE OF CONTENTS
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
All about the
Use & Care
of your Refrigerator
Important Safety Instructions ................................. 2
Features at a Glance .............................................. 4
Installation ...........................................................5
Door Removal Instructions .....................................7
Connecting Water Supply .......................................9
Controls ..............................................................10
Storage Features .................................................12
242111902 (August 2011)
Automatic Ice & Water Dispenser .........................13
Changing the Filter ..............................................15
Normal Operating Sounds and Sights ....................16
Care and Cleaning ...............................................17
Before you Call ....................................................18
Major Appliance Warranty ....................................20
2
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
Denitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top
Leveling
Refrigerator is level, side-to-side and tilted
1/4” (6mm) front-to-back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to refrigerator
No water leaks present at all connections -
recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates correctly
Frontltermustbeushwithlterhousing
(select models)
Final Checks
Shipping material removed
Fresh food and freezer temperatures set
Crisper humidity controls set
Registration card sent in
Installation Checklist
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
IMPORTANT SAFETY INSTRUCTIONS
For your Safety
• DONOTstoreorusegasoline,orotherammable
liquids in the vicinity of this or any other appliance.
Read product labels for warnings regarding
ammabilityandotherhazards.
• DONOToperatetherefrigeratorinthepresenceof
explosive fumes.
• Avoidcontactwithanymovingpartsofautomatic
ice maker.
• Removeallstaplesfromthecarton.Staplescan
causeseverecuts,andalsodestroynishesifthey
come in contact with other appliances or furniture.
WARNING
Please read all instructions before using this
refrigerator.
3
IMPORTANT SAFETY INSTRUCTIONS
Electrical information
• The refrigerator must be plugged into its
own dedicated 115 Volt, 60 Hz., 15 Amp, AC
only electrical outlet. The power cord of the
appliance is equipped with a three-prong grounding
plug for your protection against electrical shock
hazards. It must be plugged directly into a properly
grounded three prong receptacle. The receptacle
must be installed in accordance with local codes
andordinances.Consultaqualiedelectrician.
Avoid connecting refrigerator to a Ground
WARNING
These guidelines must be followed to ensure that
safety mechanisms in this refrigerator will operate
properly.
IMPORTANT
Pressing and holding the On/Off button for 3 seconds,
located on the left side of the temperature control
panel (Electronic controls), or turning the Freezer and
Fresh Food controls to “0” (Mechanical controls) will
disable your refrigerator’s cooling system, but does
not disconnect the power to the light bulb and other
electrical components. To turn off power to your
refrigerator you must unplug the power cord from the
electrical outlet.
CAUTION
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.
Child Safety
Destroy or recycle the carton, plastic bags, and any
exterior wrapping material immediately after the
refrigerator is unpacked. Children should NEVER
use these items to play. Cartons covered with rugs,
bedspreads, plastic sheets or stretch wrap may become
airtight chambers, and can quickly cause suffocation.
Proper Disposal of your Refrigerator or
Freezer
Risk of child entrapment
Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators or freezers are
still dangerous – even if they will sit for “just a few days”.
If you are getting rid of your old refrigerator or freezer,
please follow the instructions below to help prevent
accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance recycling/
disposal methods. Check with your utility company or
visit www.recyclemyoldfridge.com for more information
on recycling your old refrigerator.
Before you throw away
your old refrigerator/
freezer:
• Removedoors.
• Leaveshelvesinplace
so children may not
easily climb inside.
• Haverefrigerant
removedbyaqualied
service technician.
Fault Interrupter (GFI) circuit. Do not use an
extension cord or adapter plug.
• Ifthepowercordisdamaged,itshouldbereplaced
by an authorized service technician to prevent any
risk.
• Neverunplugtherefrigeratorbypullingonthe
powercord.Alwaysgriptheplugrmly,and
pull straight out from the receptacle to prevent
damaging the power cord.
• Unplugtherefrigeratorbeforecleaningandbefore
replacing a light bulb to avoid electrical shock.
• Performancemaybeaffectedifthevoltagevaries
by 10% or more. Operating the refrigerator with
insufcientpowercandamagethecompressor.
Such damage is not covered under your warranty.
• Donotplugtheunitintoanelectricaloutlet
controlled by a wall switch or pull cord to prevent
the refrigerator from being turned off accidentally.
4
IMPORTANT
Features not included with your refrigerator can be
purchased at www.frigidaire.com or by calling 1-800-
944-9044.
FEATURES AT A GLANCE
Features may vary according to model
SpillSafe
®
Adjustable Shelf
SpillSafe
®
Adjustable Shelf
5
NOTE
If your refrigerator is placed with the door hinge side
against a wall, you may have to allow additional space
so the door can be opened wider.
INSTALLATION
CAUTION
Do Not install the refrigerator where the temperature
will drop below 55°F (13°C) or rise above 110°F
(43°C). The compressor will not be able to maintain
proper temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your
refrigerator.Sufcientaircirculationisessentialforthe
proper operation of your refrigerator.
This Use & Care Guide provides general operating
instructions for your model. Use the refrigerator only as
instructed in this Use & Care Guide. Before starting the
refrigerator, follow these important rst steps.
Location
• Chooseaplacethatisnearagroundedelectrical
outlet. Do Not use an extension cord or an
adapter plug.
• Ifpossible,placetherefrigeratoroutofdirect
sunlight and away from the range, dishwasher or
other heat sources.
• Therefrigeratormustbeinstalledonaoorthatis
level and strong enough to support a fully loaded
refrigerator.
• Considerwatersupplyavailabilityformodels
equipped with an automatic ice maker. If you do
not hook up water to the refrigerator, remember to
turn the ice maker off.
Installation
Installation clearances
• Allowthefollowingclearancesforeaseof
installation, proper air circulation, and plumbing
and electrical connections:
Sides & Top
3
/
8
inch
Back 1 inch
Toe Grille Installation and Removal
To install toe grille
1 Open both doors. Slide left and right sides of toe
grille over lower hinges of refrigerator.
2 Whilepushingtoegrillermlyagainstcabinet,
fasten bottom clips of toe grille to cabinet.
3 Fasten top clips to cabinet.
4 Close the doors. Fasten right and left side clips
into groove of bottom hinge.
To remove toe grille
1 With both doors closed, unfasten right and left side
clips of toe grille from bottom hinge groove.
2 Openbothdoors.Pressrmlyontopoftoegrille
until top of toe grille pops off.
3 Pull toe grille outward toward your body and off of
lower hinges.
6
INSTALLATION
NOTE
The refrigerator doors are designed to shut by
themselves within a 20 degree opening.
Door Opening
Your refrigerator should be positioned to allow easy
access to a counter or table when removing food. For
best use of drawers and freezer baskets, the refrigerator
should be in a position where both the refrigerator and
freezer doors can be fully opened.
Guidelines for nal positioning of your
refrigerator:
• Allfourcornersofthecabinetmustrestrmlyon
theoor.
• Thecabinetshouldbelevelatthefrontandrear.
• Thesidesshouldtilt¼inch(6mm)fromfrontto
back (to ensure that doors close and seal properly).
• Doorsshouldalignwitheachotherandbelevel.
All of these conditions can be met by
raising or lowering the adjustable front
rollers.
To level the cabinet using the front rollers:
1 Open both doors and remove the toe grille (see
Toe Grille Installation and Removal” in the
Installation” section).
2 Closethedoorsanduseaat-bladescrewdriveror
3
/
8
inch socket wrench to raise or lower the front
rollers.
3 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides.
Hinge
Flange
Set Screw
(some models)
Door Stop
Flange
Hinge
Open Door
7/16”Wrench
and 3/32” Hex Key
(some models)
6 Replacethetoegrillebyttingitintoplace
(see “Toe Grille Installation and Removal” in the
“Installation” section).
To level the doors using the adjustable lower
hinge (some models):
1 Before leveling either door, remove set screw that
locks door height into position. (The door cannot
be adjusted without set screw removed).
2 If the refrigerator door is lower than the freezer
door, raise the refrigerator door by turning the
adjustment screw clockwise using a
7
/
16
inch
wrench. (See illustration.)
3 If the freezer door is lower than the refrigerator
door, raise the freezer door by turning the
adjustment screw clockwise using a
7
/
16
inch
wrench. (See illustration.)
4 After leveling, verify door stop contacts lower hinge
and top of door does not contact upper hinge
through full movement of door (from fully closed to
fully open).
5 Reinstall set screw, locking the door height.
7
DOOR REMOVAL INSTRUCTIONS
Getting through narrow spaces
Ifyourrefrigeratorwillnottthroughanentrancearea,youcanreduceitssizebyremovingthedoors.Checkrstby
measuring the entrance.
Required Tools
You will need the following tools:
To prepare for removing the doors:
1 Make sure the electrical power cord is unplugged from the wall outlet.
2 Open both doors and remove the toe grille (as explained in the Installation
Instructions that came with your appliance).
3 Remove any food from the door shelves.
4 Close the doors.
To remove the refrigerator top hinge cover:
1 Remove the three screws from each cover over the top door hinges.
2 Lift hinge cover straight up and off.
To remove the refrigerator door:
1 Trace lightly around the door’s top hinge with a pencil. This makes reinstallation
easier.
2 Remove the two screws from the top hinge. Lift the door off of the bottom hinge
and set it aside.
3 Remove the two bottom hinge screws and hinge if necessary.
Adjustable
Wrench
Socket
Wrench Set
OR
Phillips Head
Tools Necessary:
3/8” Fixed
Wrench
AND
OR
Top Hinge
Cover Rear
Screw
Top Hinge
Cover Front
Screw
Bottom
Hinge
Screw
Top
Hinge
Screw
Adjustable Hinge
(some models)
Non-Adjusting Hinge
(some models)
To reinstall the refrigerator door, reverse the above steps.
CAUTION
Be sure doors are set aside in a secure
position where they cannot fall and cause
personal injury.
8
To remove the freezer top hinge cover:
1 Remove the two screws from each cover over the
top door hinges.
2 Lift hinge cover straight up and off.
To remove the freezer door:
1 Detach the multi-wire cable connector located
above the top hinge. Grasp both sides of the
connectorrmlyandpullapart.
3 Detach the water tube from the connector
located below the freezer door. The connector
releases when you press its outer sleeve inward.
4 Remove the screws from the top hinge and
pull the multi-wire cable through it. Lift the
door off of the bottom hinge.
5 Remove the two bottom hinge screws and
hinge if necessary.
6 Lay the door on its side to avoid damage to
the water tube extending from the bottom
hinge.
To reinstall the freezer door, reverse the above steps.
Once both doors are in place, ensure they are aligned
with each other and level (Please see “To level the doors
using the lower hinge” for models with adjustable lower
hinges or “To level the cabinet using the front rollers”
for models with the non-adjustable lower hinges in the
“Installation” section.), then replace the top hinge cover.
Non-Adjusting Hinge (some models)
Adjustable Hinge (some models)
2 Trace lightly around the hinge with a pencil.
This makes reinstallation easier.
DOOR REMOVAL INSTRUCTIONS
9
WARNING
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the refrigerator.
NOTE
Check with your local building authority for
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes, Frigidaire
recommends for homes with existing valves its Smart
Choice® water line kit 5305513409 (with a 6 ft.
Stainless Steel Water Line) and for homes without an
existing valve, Frigidaire recommends its Smart Choice
water® line kit 5305510264 (with a 20 ft. Copper Water
Line with self-tapping saddle valve). Please refer to
www.frigidaire.com/store for more information.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing is
recommended for the water supply line. Water
supply tubing made of ¼ inch plastic is not
recommended to be used. Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer will not be responsible for any
damage if plastic tubing is used for the supply line.
DO NOT install water supply tubing in areas
where temperatures fall below freezing.
Chemicals from a malfunctioning softener
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections comply
with all local plumbing codes.
IMPORTANT
After connecting the water supply, refer to “How to Prime
the Water Supply System” for important information about
priming an empty water supply system.
Your refrigerator’s water supply system includes several tubing
lines,awaterlter,awatervalve,andawatertank.Toensure
that your water dispenser works properly, this system must be
completelylledwithwaterwhenyourrefrigeratorisrst
connected to the household water supply line.
CONNECTING THE WATER SUPPLY
Before Installing The Water Supply Line, You Will Need:
• BasicTools:adjustablewrench,at-blade
screwdriver, and Phillips
TM
screwdriver
• Accesstoahouseholdcoldwaterlinewithwater
pressure between 30 and 100 psi.
• Awatersupplylinemadeof¼inch(6.4mm)OD,
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
• Ashutoffvalvetoconnectthewatersupplylineto
your household water system. DO NOT use a self-
piercing type shutoff valve.
• Acompressionnutandferrule(sleeve)forconnecting
a copper water supply line to the ice maker inlet valve.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket.
TurnONwatersupplyandushsupplylineuntil
water is clear. Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line. Push
water supply line into water valve inlet as far as it will
go(¼inch/6.4mm).Slideferrule(sleeve)intovalve
inletandngertightencompressionnutontovalve.
Tighten another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing. Slide
compressionnutontovalveinletandngertighten
compression nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel of
refrigerator as shown.
6. Coil excess water supply line (copper tubing only),
about 2½ turns, behind refrigerator as shown and
arrange coils so they do not vibrate or wear against
any other surface.
7. Turn ON water supply at shutoff valve and tighten
any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (side
mounted) or set the ice maker’s On/Off power
switch to the “I” position (rear mounted).
Figure 2
Figure 1
Copper water line
from household water supply
(Includeenough tubing in loop to allow
moving refrigerator out for cleaning.)
Ferrule
(Sleeve)
Copper
water line
WaterValve
Valve Inlet
Water Valve
Bracket
Steel
Clamp
Plastic Water Tubing
to Ice Maker
Fill Tube
Brass
Compression
Nut
10
CONTROLS
User Interface
Your refrigerator is equipped with a user interface display.
Touch an icon (Water/Cube/Crush) to activate the
desired dispenser mode.
light on-off On / Off
control lock Press and hold for three (3) seconds
to activate and deactivate. This
restricts undesired changes to the
refrigerator’s settings and prevents
use of the ice and water dispenser.
water lter Touchtodisplayltercondition
status. Press and hold for three (3)
seconds to reset.
C/F Touch to toggle display from Fahren-
heit to Celsius. Press and hold for
three (3) seconds for display on-off.
When active, it allows the display of
the freezer and fridge temps.
power on-off Press and hold for three (3) seconds
to turn off the cooling system to
clean the refrigerator. It also turns
off all dispenser functions. The tem-
perature display will read OFF.
IMPORTANT
Pressing the power off icon does not turn off power to
your refrigerator. You must unplug the power cord from
the wall outlet.
Express-Select
®
Setting Cooling Temperatures
Press the orindicator to adjust the temperature to the
desired setting. The temperature display will begin to blink
Sabbath Mode
The Sabbath Mode is a feature that disables portions
of the refrigerator and its controls in accordance with
observance of the weekly Sabbath and religious holidays
within the Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by pressing and
holding "" on freezer temp and "" on refrigerator
temp forveseconds.Thedisplayshows“Sb”whilein
Sabbath mode.
In the Sabbath Mode, the High Temp alarm is active
for health reasons. If a high temperature alarm is
activated during this time, for example due to a door
left ajar, the alarm will sound intermittently for about
10 minutes. The alarm will then silence on its own and
a red high temperature icon will display. The high temp
icon will continue to display, even if the door is closed,
until the Sabbath mode is exited and the icon reset. The
refrigerator will function normally once the door is closed,
without any violation of the Sabbath/Holidays.
For further assistance, guidelines for proper usage and
a complete list of models with the Sabbath
feature, please visit the web at http:\\www.
star-k.org.
NOTE
Although you have entered the Sabbath mode, the ice
maker will complete the cycle it had already initiated.
The ice cube compartment will remain cold and new ice
cubes can be made with standard trays.
withthersttouch.Afterve(5)secondsofinactivity,the
display will beep to accept the new temperature.
11
CONTROLS
Express-Select
®
User Interface
Your refrigerator is equipped with a user interface display.
It is only necessary to touch the glass. There is no need
to press with force.
Touch an icon (Water/Cube/Crush) to activate the
desired dispenser mode.
light on-off On / Off
control lock Press and hold for three (3) seconds to
activate and deactivate. The Lock icon
will be displayed in the LCD window.
This restricts undesired changes to the
refrigerator’s settings and prevents use
of the ice and water dispenser.
lter reset Touchtodisplayltercondition
status. Press and hold for three (3)
seconds to reset.
C/F Touch to toggle display from Fahr-
enheit to Celsius.
power on-off Press and hold for three (3) seconds
to turn off the cooling system to
clean the refrigerator. It also turns
off all dispenser functions. The tem-
perature display will read OFF.
IMPORTANT
Pressing the power off icon does not turn off power to
your refrigerator. You must unplug the power cord from
the wall outlet.
Setting Cooling Temperatures
Press set temp to choose which compartment, refrigerator or
freezer, to adjust. The temperature display will begin to blink
withthersttouch.Touchbuttonnextto+or-toadjustthe
temperaturetothedesiredsetting.Afterve(5)secondsof
inactivity, the display will beep to accept the new temperature.
Sabbath Mode
The Sabbath Mode is a feature that disables portions
of the refrigerator and its controls in accordance with
observance of the weekly Sabbath and religious holidays
within the Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by pressing and
holding power on-off and control lock forveseconds.
The display shows “Sb” while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is active
for health reasons. If a high temperature alarm is
activated during this time, for example due to a door
left ajar, the alarm will sound intermittently for about
10 minutes. The alarm will then silence on its own and
a red high temperature icon will display. The high temp
icon will continue to display, even if the door is closed,
until the Sabbath mode is exited and the icon reset. The
refrigerator will function normally once the door is closed,
without any violation of the Sabbath/Holidays.
For further assistance, guidelines for proper usage and
a complete list of models with the Sabbath
feature, please visit the web at http:\\www.
star-k.org.
NOTE
Although you have entered the Sabbath mode, the ice
maker will complete the cycle it had already initiated.
The ice cube compartment will remain cold and new ice
cubes can be made with standard trays.
12
CAUTION
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change. See “Glass Shelves” in Care &
Cleaning Chart.
STORAGE FEATURES
Cantilever Sliding Glass Shelf
1
2
Cantilever Glass Shelf
1
2
Cantilever Shelf Adjustment
Refrigerator shelves are easily adjusted to suit individual
needs. Before adjusting the shelves, remove all food.
Cantilever shelves are supported at the back of the
refrigerator.
To adjust cantilever shelves:
1 Lift front edge up.
2 Pull shelf out.
Replace the shelf by inserting the hooks at rear of the
shelf into the wall bracket. Lower the shelf into the
desired slots and lock into position.
SpillSafe
TM
glass shelves (some models) catch and hold
accidental spills. In some models, the SpillSafe
TM
shelves
slide out for easy access to food and for fast cleaning.
The shelves slide out independently of their mounting
brackets. Just pull the front of the shelf forward. Shelves
can be extended as far as the stopper will allow but are
not removable from their mounting brackets.
Door storage
Door bins and shelves are provided for convenient
storage of jars, bottles, and cans. Frequently used items
can be quickly selected.
Some models have door bins that can accommodate
gallon-sized plastic drink containers and economy-
sized jars and containers. Some bins are adjustable for
maximum storage capacity.
The dairy compartment, which is warmer than the
general food storage section, is intended for short term
storage of cheese, spreads, or butter.
Fresh Drawers with Humidity Control
(some models)
The fresh drawers, located under the bottom refrigerator
shelf, are designed for storing fruits, vegetables, and other
Crisper Drawer
Crisper Humidity Control
Cool Drawer (some models)
Some models are equipped with a Cool Drawer for
storage of luncheon meats, spreads, cheeses, and
other deli items. This drawer does not have a separate
temperature control
Chill Drawer (some models)
Some models are equipped with a Chill Drawer. Chill
Drawer temperatures can be adjusted by sliding the Chill
Drawer Temperature Control in either direction. Use this
pan for short term storage of bulk meat items. If meats
are to be kept longer than one or two days, they should
befrozen.TheChillDrawerisxedandcannotbemoved
up or down. If fruits or vegetables are to be stored in the
Chill Drawer, set the Chill Drawer Temperature Control to
a warmer setting to prevent freezing.
NOTE
Leafy vegetables keep best when stored with the
humidity control set on Higher Humidity, or in a
drawer without a Humidity Control. This keeps incoming
air to a minimum and maintains maximum moisture
content.
Crispers
Crispersallowyoutheexibilityto
store any manner of items including
fruits, vegetables, nuts, etc.
Crispers do not feature humidity
controls.
Chill Drawer
with Temperature Control
fresh produce. The fresh drawers feature humidity control
which allows you to adjust the humidity within the
drawer. This can extend the life of fresh vegetables that
keep best in high humidity. Wash items in clear water and
remove excess water before placing them in the crispers.
Items with strong odors or high moisture content should be
wrapped before storing.
13
AUTOMATIC ICE & WATER DISPENSER
Priming the Water Supply System
Your refrigerator’s water supply system includes several
tubinglines,anadvancedwaterlter,adistributionvalve
bank, and a reserve tank to ensure ample supply to the
ice and water dispenser at all times. This system needs
tobecompletelylledwithwaterwhenrstconnectedto
an external supply line.
To prime the water supply system:
1 Beginllingthetankbypressingandholdinga
drinking glass against the water dispenser paddle.
2 Keep the glass in this position until water comes
out of the dispenser. It may take about 1½
minutes.
3 Continue dispensing water for about four minutes
toushthesystemandplumbingconnectionsof
any impurities (stopping to empty the glass as
necessary).
Ice Maker Operation & Care
The ice maker, ice bin, and dispenser feeding mechanism
are located in the top of the freezer compartment. After
the refrigerator is installed properly and has cooled for
several hours, the ice maker can produce ice within 24
hours.Itcancompletelyllanicebininabouttwodays.
OFF
ON
Wire
Signal Arm
NOTE
The water dispenser has a built-in device that shuts
offthewaterowafterthreeminutesofcontinuous
use. To reset this shutoff device, simply release the
dispenser paddle.
CAUTION
For proper dispenser operation, recommended water
supply pressure should fall between 30 psi and 100
psi.Excessivepressuremaycausewaterlterto
malfunction.
ON
OFF
Wire
Signal Arm
IMPORTANT
Your ice maker is shipped from the factory with the
wire signal arm in the ON position (side mounted) or
with the switch turned ON (rear mounted). To ensure
proper function of your ice maker, hook up water
supply immediately or turn ice maker OFF by lifting
the wire signal arm until it clicks and locks in the UP
position (side mounted) or turn the On/Off switch
to the Off (0) position (rear mounted). If the ice
maker is not turned off and the water supply is
not connected, the water valve will make a loud
chattering noise..
Using the Ice Maker after Installation
Beforemakingiceforthersttime,besuretoprimethe
water supply system. Air in new plumbing lines can result
in two or three empty ice maker cycles. Furthermore,
ifthesystemisnotushed,thersticecubesmaybe
discoloredorhaveanoddavor.
Turning the SIDE MOUNTED Ice Maker
On and Off
To begin ice production, lower the wire signal arm to
the DOWN or ON position. The ice maker turns off
automatically when the ice container becomes full. To
stop the ice maker, raise the wire signal arm until it clicks
and locks in the UP or OFF position.
Turning the REAR MOUNTED Ice Maker
On and Off
Ice production is controlled by the ice maker’s ON/OFF
power switch. To gain access to the ice maker, pull the
ice cream shelf out. Press the switch to the “O” position
to turn it Off and press it to the “I” position to turn it On.
The ice maker also has a built-in wire signal arm, which
automatically stops ice production when the ice bin is
full. DO NOT use this signal arm to manually stop the ice
maker.
Ice Production: What to Expect
How Much Ice Will a Side Mounted Ice Maker
Produce in 24 Hours?
A side mounted ice maker will produce 4 to 4.5 pounds of
ice every 24 hours, depending on usage conditions. Ice is
produced at a rate of 8 cubes every 75 to 90 minutes.
How Much Ice Will a Rear Mounted Ice Maker
Produce in 24 Hours?
A rear mounted ice maker will produce 3 to 4 pounds of
ice every 24 hours, depending on usage conditions. Ice is
produced at a rate of 8 cubes every 75 to 90 minutes.
14
AUTOMATIC ICE & WATER DISPENSER (CONTINUED)
CAUTION
Chemicals from a malfunctioning water softener
can damage the ice maker. If the water supply to
your refrigerator is softened, be sure the softener is
maintained to work properly.
CAUTION
NEVER use an ice pick or similar sharp instrument to
break up the ice. This could damage the ice storage bin
and dispenser mechanism.
IMPORTANT
When removing or replacing the ice bin, DO NOT rotate
the auger in the ice bin. If the auger is accidentally
rotated, you must realign the auger by turning it in 90
degreeturns(seebelow)untiltheicebintsintoplace
with the drive mechanism. If the auger is not properly
aligned when replacing the ice bin, the refrigerator will
only dispense Crushed Ice. The freezer door may also not
close properly causing warm air to leak into the freezer.
IMPORTANT
Small ice cubes or ice chips jamming in the ice maker may
beasignthatyourwaterlterneedschanging.Ifyou
have a side mounted ice maker you may also experience
hollow cubes partially frozen cubes with water inside. When
these cubes are harvested, they break open and spill water
over the other ice cubes in the ice container, forming a
solidmassofice.Asthewaterlternearstheendofits
useful life and becomes clogged with particles, less water is
delivered to the ice maker during each cycle. The ice maker
can’tlleverycubeintheicemakermold,leadingtosmall
cubes or chips that can get caught between the ice ejector
blades and the stripper. Remember, if your ice maker is
jamming with small ice cubes or it’s been six months or
longersinceyoulastchangedyourwaterlterreplacethe
waterlterwithanewone.Poorqualityhouseholdwater
mayrequiretheltertobechangedmorefrequently.
Ice Maker/Dispenser Tips
• Icecubesstoredtoolongmaydevelopanodd
avor.Emptytheicecontainerasexplainedbelow.
• Occasionallyshaketheicecontainertokeepice
separated.
• Ifyourrefrigeratorisnotconnectedtoawater
supply or the water supply is turned off, turn Off
the ice maker.
• Ifyouneedalargequantityoficeatonetime,itis
best to get cubes directly from the ice container.
• Thefollowingsoundsarenormalwhentheice
maker is operating:
- Motor running
- Ice dropping into ice container
- Water valve opening or closing
- Ice loosening from tray
- Running water
• Whendispensingice,youwillhearasnapping
or clicking sound when the ice chute opens and
closes.
• TurnOff the ice maker when cleaning the freezer
and during vacations.
- If you turn Off the ice maker for a long period of
time, you should also turn off the water supply
valve.
Cleaning the Ice Maker
Clean the ice maker and ice bin at regular intervals,
particularly before you take a vacation or move.
To clean the ice maker:
1 Turn Off the ice maker.
2 Remove the ice bin by lifting up and out.
3 Empty and carefully clean the ice bin with mild
detergent. Rinse with clear water. Do not use harsh
or abrasive cleaners.
4 Allow the ice bin to dry completely before replacing
in the freezer.
5 Remove ice chips and clean the ice bin shelf and
the freezer door chute.
6 Replace the ice bin. Turn On the ice maker to
resume ice production.
Remove and empty the ice storage bin if:
• Anextendedpowerfailure(onehourorlonger)
causes ice cubes in the ice storage bin to melt and
freeze together, jamming the dispenser mechanism.
• Youdonotusetheicedispenserfrequently.Ice
cubes will freeze together in the bin, jamming the
dispenser mechanism.
Remove the ice storage bin and shake to loosen the
cubes or clean as explained above.
15
CHANGING THE FILTER
Ordering Replacement Filters
Toorderyourreplacementlters,pleasevisitouronline
store at www.frigidaire.com/store, by calling toll-free
at 877-808-4195, or by visiting the dealer where you
purchased your refrigerator. Frigidaire recommends that you
orderextralterswhenyourstinstallyourrefrigerator,and
thatyoureplaceyourltersatleastonceeverysixmonths.
Water Filter
Thewaterlterislocatedatthetoprightsideofthefresh
food compartment.
Replacing the Water Filter
Ingeneral,youshouldchangethewaterltereverysix
months to ensure the highest possible water quality. Water
Filter Status on the user interface prompts you to replace
thelterafterastandardamountofwater(200gallons/757
liters for PureSource 3
TM
)
hasowedthroughthesystem.
If your refrigerator has not been used for a period of time
(duringmovingforexample),changethelterbefore
reinstalling the refrigerator.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
thesystem.Systemscertiedforcystreductionmaybeused
ondisinfectedwatersthatmaycontainlterablecysts.
Test & certication results:
• RatedCapacity-200gallons/757litersfor
PureSource 3
TM
iceandwaterlter
• Ratedserviceow-.50gallonsperminute
• OperatingTemp.:Min.33°F,Max.100°F
• MaximumRatedPressure-100poundspersquareinch
• RecommendedMinimumOperatingPressure:30
pounds per square inch
To replace your PureSource 3
TM
water lter:
It is not necessary to turn the water supply off to change
thelter.Bereadytowipeupanysmallamountsofwater
releasedduringthelterreplacement.
1 Turn Off the ice maker.
2 Removethelterbypushingontheend/faceofthe
lter.
3 Slidetheoldwaterltercartridgestraightoutofthe
housing and discard it.
4 Unpackagethenewltercartridge.Usingthe
alignmentguide,slideitgentlyintothelterhousing
until it stops against the snap-in connector at the
back of the housing.
5 Push rmly until the cartridge snaps into
place (you should hear a click as the cartridge
engages the snap-in connector).
6 Press a drinking glass against the water dispenser
whilecheckingforanyleaksatthelterhousing.
Any spurts and sputters that occur as the system
purges air out of the dispenser system are normal.
7 Afterllingoneglassofwater,continueushingthe
system for about four minutes.
8 Turn On the ice maker.
9 Press and hold the Water Filter button on the Ice
& Water Dispenser control panel for three seconds.
When the display changes from Red to Green, the
status has been reset.
The PureSource 3
TM
iceandwaterlter
systemistestedandcertiedtoNSF/ANSI
Standards 42 and 53 for the reduction of claims
speciedontheperformancedatasheet.
More about your Advanced Water Filter
Air Filter (some models)
Theairlterislocatedatthetopofthefreshfood
compartmentnexttothewaterlter.
Replacing the Air Filter
Ingeneral,youshouldchangetheairltereverysix
months(thelterstatuslightonthecontrolpanelprompts
youtoreplacethelteraftersixmonths)toensureoptimal
lteringofrefrigeratorodors.Youmaywanttoadjustthis
time period depending on the types and amounts of food
you typically store in your refrigerator. To replace you
PureSource Ultra
TM
airlter:
1 Pulltheairlterhousingstraightout.
2 Removetheoldlteranddiscardit.
3 Unpackthenewlterandplaceitinsidethehousing.
4 Slide the housing back into position.
Here is the product number to request when ordering:
PureSource 3
TM
Water Filter
Part #WF3CB
PureSource Ultra
TM
Air Filter
Part #PAULTRA
16
NOTE
Energyefcientfoaminyourrefrigeratorisnotasound
insulator.
Understanding the Sounds you may Hear
Yournew,high-efciencyrefrigeratormayintroduce
unfamiliar sounds. These sounds normally indicate
your refrigerator is operating correctly. Some surfaces
onoors,walls,andkitchencabinetsmaymakethese
sounds more noticeable.
Following is a list of major components in your
refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the evaporator
may create a boiling or gurgling sound.
B Evaporator fan You may hear air being forced
through the refrigerator by the evaporator fan.
C Defrost heater During defrost cycles, water
dripping onto the defrost heater may cause a
hissing or sizzling sound. After defrosting, a
popping sound may occur.
D Automatic ice maker When ice has been
produced, you will hear ice cubes falling into the
ice bin.
E Electronic control & automatic defrost
control These parts can produce a snapping or
clicking sound when turning the cooling system on
and off.
F Condenser fan You may hear air being forced
through the condenser.
G CompressorModern,high-efciencycompressors
run much faster than in the past. The compressor
may have a high-pitched hum or pulsating sound.
H Water valve Makes a buzzing sound each time it
openstolltheicemaker.
I Drain pan (not removable) You may hear water
dripping into the drain pan during the defrost cycle.
J Condenser May create minimal sounds from
forced air.
K Motorized damper May produce a light
humming during operation.
L Ice chute When dispensing ice, you will hear
a snapping or clicking sound when the solenoid
opens and closes the ice chute.
NOTE
During automatic defrost cycle, a red glow in the back
wall vents of your freezer compartment is normal.
D
OR
NORMAL OPERATING SOUNDS AND SIGHTS
17
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain the water supply system. Failure to do so
could result in water leaks when the refrigerator is put back into service. Contact a service representative to perform this operation.
CAUTION
• Pulltherefrigeratorstraightouttomoveit.Shiftingitfromsidetosidemaydamageooring.Becarefulnottomovethe
refrigerator beyond the plumbing connections.
• Dampobjectssticktocoldmetalsurfaces.Donottouchrefrigeratedsurfaceswithwetordamphands.
NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical components will continue until you
unplug the power cord from the wall outlet.
Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any spills immediately and clean the
freezer and fresh food compartments at least twice a year. When cleaning, take the following precautions:
• NeveruseCHLORIDEorcleanerswithbleachtocleanstainlesssteel.
• Donotwashanyremovablepartsinadishwasher.
• Alwaysunplugtheelectricalpowercordfromthewalloutletbeforecleaning.
• Removeadhesivelabelsbyhand.Donotuserazorbladesorothersharpinstrumentswhichcanscratchtheappliancesurface.
• Donotremovetheserialplate.
Donotuseabrasivecleanerssuchaswindowsprays,scouringcleansers,brushes,ammableuids,cleaningwaxes,concentrated
detergents, bleaches or cleansers containing petroleum products on plastic parts, interior doors, gaskets or cabinet liners. Do not
use paper towels, metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions.
CARE & CLEANING
Care & Cleaning Tips
Part What To Use Tips and Precautions
Interior & Door
Liners
• Soap and water
• Baking soda and water
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to
wring excess water out of sponge or cloth before cleaning around
controls, light bulb or any electrical part.
Door Gaskets • Soap and water Wipe gaskets with a clean soft cloth.
Drawers & Bins • Soap and water Use a soft cloth to clean drawer runners and tracks.
Glass Shelves • Soap and water
• Glass cleaner
• Mild liquid sprays
Allow glass to warm to room temperature before immersing in warm water.
Toe Grille • Soap and water
• Mild liquid sprays
• Vacuum attachment
Vacuum dust from front of toe grille. Remove toe grille (see Installation
Instructions). Vacuum backside, wipe with sudsy cloth or sponge. Rinse
and dry.
Exterior &
Handles
• Soap and water
• Non Abrasive Glass Cleaner
Do not use commercial household cleaners containing ammonia, bleach or
alcohol to clean handles. Use a soft cloth to clean smooth handles. DO
NOT use a dry cloth to clean smooth doors.
Exterior &
Handles
(Stainless Steel
Models Only)
• Soap and water
• Stainless Steel Cleaners
Never use CHLORIDE or cleaners with bleach to clean stainless steel.
Clean stainless steel front and handles with non-abrasive soapy water and
a dishcloth. Rinse with clean water and a soft cloth. Use a non-abrasive
stainless steel cleaner. These cleaners can be purchased at most home im-
provement or major department stores. Always follow manufacturer’s in-
structions. Do not use household cleaners containing ammonia or bleach.
NOTE: Always clean, wipe and dry with the grain to prevent
scratching. Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well, and wipe dry with a clean soft cloth.
Replacing Light
Bulbs
• Unplug refrigerator
• Wear gloves
• Remove light cover
• Replace old bulb
• Replace light cover
• Plug in the refrigerator
CAUTION: Wear gloves when replacing light bulbs to avoid get-
ting cut.
Use same wattage when replacing bulb
18
BEFORE YOU CALL
Visit our web site at
www.frigidaire.com.
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
PROBLEM CAUSE CORRECTION
AUTOMATIC ICE MAKER
Ice maker is not mak-
ing any ice.
• Ice maker wire signal arm is in
the “up” or OFF position.
• Ice maker power switch is Off.
• Ice maker has small cube
caught in mechanism.
• Saddle valve on cold water
pipe is clogged or restricted by
foreign material.
• Move wire signal arm to the “down” or ON position. (side
mounted)
• Turn power switch to On (“I”) position. (rear mounted)
• Remove small cube from ice maker. The ice and water
ltercartridgemaybeclogged.Replaceltercartridge.
• Turn off household water line valve. Remove valve. En-
sure that valve is not a self-piercing saddle valve. Clean
valve. Replace valve if necessary.
Ice maker is not mak-
ing enough ice.
• Ice maker is producing less ice
than you expect.
• Check to see if water dispenser
is dispensing slower than normal.
• Side mounted ice maker should produce 4 to 4.5 pounds
(approximately 4 quarts) of ice every 24 hours. A rear
mounted ice maker should produce 3 to 4 pounds (ap-
proximately 3½ quarts) of ice every 24 hours. Quick Ice
option should produce up to 50% more ice every 24 hours.
• Ifitis,replacetheiceandwaterltercartridge.
Ice maker will not stop
making ice.
• Ice maker wire signal arm is
being held down by some item
in the freezer.
• Move item and release wire signal arm. Remove any ice
cubes that are frozen together over the wire signal arm.
Ice cubes are freezing
together.
• Ice cubes are not being used
frequently enough.
• Ice cubes are hollow (partially
frozen cubes with water inside).
• Freezer control is set too warm.
• Remove ice container and discard ice from container. Ice
maker will produce fresh supply.
• Theiceandwaterltercartridgemaybeclogged.Replace
ltercartridge.
• Set freezer control to colder setting. Allow 24 hours for
temperature to stabilize.
ICE DISPENSER
Dispenser will not dis-
pense ice.
• Ice storage container is empty.
• Freezer temperature is set too
warm.
• Household water line valve is
not open.
• Ice dispensing arm has been held
in for more than 4-5 minutes.
• Whentherstsupplyoficeisdroppedintothecontainer,
the dispenser should operate.
• Turn freezer control to a higher setting so that ice cubes
willbemade.Whenrstsupplyoficeismade,dispenser
should operate.
• Openhouseholdwaterlinevalve.Allowsufcienttime
for the ice to be made. When ice is made, the dispenser
should operate.
• Motor is overloaded. Motor over load protector will reset in
approximately 3 minutes. Ice can then be dispensed.
Ice dispenser is
jammed.
• Ice has melted and frozen
around auger due to infrequent
use,temperatureuctuations,
and/or power outages.
• Ice cubes are jammed between
ice maker and back of ice
container.
• Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper position.
When new ice is made, dispenser should operate.
• Remove ice cubes that are jamming the dispenser.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not close. • Door was closed too hard, caus-
ing other door to open slightly.
• Refrigerator is not level. It
rocksontheoorwhenmoved
slightly.
• Refrigerator is touching a wall
or cabinet.
• Close both doors gently.
• Ensureoorislevelandsolid,andcanadequatelysupport
the refrigerator. Contact a carpenter to correct a sagging
orslopingoor.
• Ensureoorislevelandsolid,andcanadequatelysupport
the refrigerator. Contact a carpenter to correct a sagging
orslopingoor.
Drawers are difcult to
move.
• Food is touching shelf on top of
drawer.
• Track that drawers slide on is
dirty.
• Remove top layer of items in drawer.
• Ensure drawer is properly installed on track.
• Clean drawer, rollers, and track. See Care & Cleaning.
19
BEFORE YOU CALL (CONTINUED)
PROBLEM CAUSE CORRECTION
RUNNING OF REFRIGERATOR
Compressor does not
run.
• Freezer control is set to “OF”
or “0”.
• Refrigerator is in defrost cycle.
• Plug at electrical outlet is dis-
connected.
• House fuse blown or tripped
circuit breaker.
• Power outage.
• Set freezer control.
• This is normal for a fully automatic defrost refrigerator.
The defrost cycle occurs periodically, lasting about 30
minutes.
• Ensure plug is tightly pushed into outlet.
• Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
• Check house lights. Call local electric company.
Refrigerator runs too
much or too long.
• Room or outside weather is
hot.
• Doors are opened too frequent-
ly or too long.
• Fresh Food/freezer door may
be slightly open.
• Freezer control is set too cold.
• Fresh Food/freezer gasket is
dirty, worn, cracked, or poorly
tted.
• Condenser is dirty.
• It’s normal for the refrigerator to work longer under these
conditions.
• Warm air entering the refrigerator causes it to run more.
Open doors less often.
• Ensure refrigerator is level. Keep food and contains from
blocking door. See PROBLEM column OPENING/CLOSING
OF DOORS/DRAWERS.
• Set Fresh Food control to warmer setting until refrigerator
temperature is satisfactory. Allow 24 hours for tempera-
ture to stabilize.
• Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatures.
• Clean condenser. See Care & Cleaning.
Compressor goes off
and on frequently.
• Thermostat keeps the refrigera-
tor at a constant temperature.
• This is normal. Refrigerator goes on and off to keep tem-
perature constant.
DIGITAL TEMPERATURE DISPLAY
Digital temperature
displays are ashing.
• Electronic control system has
detected a performance prob-
lem.
• Call your Frigidaire service representative, who can inter-
pretanymessagesornumbercodesashingonthedigital
displays.
WATER DISPENSER
Dispenser will not dis-
pense water.
• Household water line valve is
not open.
• Iceandwaterltercartridgeis
clogged.
• Filter not fully installed.
• Open household water line valve. See PROBLEM column
AUTOMATIC ICE MAKER.
• Replaceltercartridge.
• Pushlterinuntilyouheara“click”.
Water has an odd taste
and/or odor.
• Water has been in the tank for
a period of time.
• Unit not properly connected to
cold water line.
• Draw and discard 10-12 glasses of water to freshen the
supply and completely rinse out the tank.
• Connect unit to cold water line that supplies water to the
kitchen faucet.
Water pressure is ex-
tremely low.
• Cut-off and cut-on pressures
are too low (well systems only).
• Reverse osmosis system is in
regenerative phase.
• Have someone turn up the cut-off and cut-on pressure on
the water pump system (well systems only).
• It is normal for a reverse osmosis system to be below 20
psi during the regenerative phase.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
Moisture collects on
inside of refrigerator
walls.
• Weather is hot and humid.
• Door is slightly open.
• The rate of frost buildup and internal sweating increases.
• See PROBLEM column OPENING/CLOSING OF
DOORS/DRAWERS.
Water collects on bot-
tom side of drawer
cover.
• Vegetables contain and give off
moisture.
• It is not unusual to have moisture on the bottom side of
the cover.
• Move humidity control (some models) to lower setting.
Water collects in bot-
tom of drawer.
• Washed vegetables and fruit
drain while in the drawer.
• Dry items before putting them in the drawer. Water col-
lecting in bottom of drawer is normal.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
Moisture collects on
outside of refrigerator
or between doors.
• Weather is humid.
• Door is slightly open, causing
cold air from inside refrigerator
to meet warm air from outside.
• This is normal in humid weather. When humidity is lower,
the moisture should disappear.
• See PROBLEM column OPENING/CLOSING OF
DOORS/DRAWERS.
20
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Servicecallstorepairorreplaceappliancelightbulbs,airlters,waterlters,otherconsumables,or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12.Damagestothenishofapplianceorhomeincurredduringinstallation,includingbutnotlimitedtooors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
externalcausessuchasabuse,misuse,inadequatepowersupply,accidents,res,oractsofGod.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR
OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED
WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
Exclusions
If You Need
Service
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
thiswarrantymustbeperformedbyElectroluxoranauthorizedservicecompany.Productfeaturesorspecicationsasdescribed
or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
North America
10200 David Taylor Drive
Charlotte, NC 28262
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Frigidaire DGUS2635LP User manual

Category
Side-by-side fridge-freezers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI