11
CONTENTS GB
BEFORE USING THE REFRIGERATOR
PAGE
12
SAFEGUARDING THE ENVIRONMENT
PAGE
12
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
13
HOW TO OPERATE THE REFRIGERATOR
COMPARTMENT
PAGE
14
HOW TO OPERATE THE LOW TEMPERATURE
COMPARTMENT
PAGE
15
HOW TO DEFROST AND CLEAN THE
REFRIGERATOR
PAGE
16
CARE AND MAINTENANCE
PAGE
17
TROUBLESHOOTING GUIDE
PAGE
17
AFTER-SALES SERVICE
PAGE
18
INSTALLATION
PAGE
18
ELECTRICAL CONNECTION
PAGE
19
1gb37030a.fm5 Page 11 Friday, February 9, 2001 7:50 PM
12
Your new appliance is exclusively for domestic
use.
Use the
low temperature compartment,
if
fitted
,
for making ice cubes, storing frozen and
deep-frozen foods and freezing fresh and
cooked foods (only in the compartment
marked );
defrosting is a manual
procedure
. The
refrigerator compartment
,
which has an
automatic defrost feature
, is
used for the storage of fresh food and
beverages.
To get the most out of your new appliance,
read the user handbook thoroughly. The
handbook contains a description of the
appliance and useful tips for storing food.
Keep this handbook for future consultation.
1.
After unpacking the appliance, make sure
that the door shuts properly.
Any damage must be reported to your dealer
within 24 hours after delivery of the
appliance.
2. Wait at least two hours before connecting
the appliance to the power supply in order
to ensure the refrigerant circuit is fully
efficient.
3.
Installation of the appliance and electrical
connections must be carried out by a
qualified electrician, in accordance with the
manufacturer's instructions and local
regulations.
1. Packing
The packaging material is entirely recyclable,
and marked with the recycling symbol.
Follow local regulations for scrapping.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2. Appliance
The appliance is made using recyclable
materials. Dispose of the appliance in conformity
with local environmental regulations.
Make the appliance unusable by cutting off the
power cord. The appliance must be delivered to
an authorised collection centre for the recovery
of refrigerant gas.
Information:
This appliance does not contain CFCs (replaced
with R134a) or HFCs (replaced with R600a -
Isobutane). For more information, refer to the
identification data plate affixed to the appliance.
BEFORE USING THE REFRIGERATOR
SAFEGUARDING THE ENVIRONMENT
1gb37030a.fm5 Page 12 Friday, February 9, 2001 7:50 PM
13
•
Use the
refrigerator compartment
only for
storing fresh foods and the
low temperature
compartment
only for making ice cubes,
storing frozen foods and freezing fresh foods
(only in the compartment marked ).
•
Do not cover or obstruct the air vents of the
appliance.
•
Do not store liquids in glass containers in the
low temperature compartment - risk of
bursting.
•
Do not eat ice cubes or ice lollies immediately
after taking them out of the low temperature
compartment - risk of "cold" burns.
•
Do not allow children to play or hide inside
the appliance - risk of becoming trapped and
suffocating.
•
Before servicing or cleaning the appliance,
unplug it from the mains or disconnect the
electrical power supply.
•
The power cable may only be replaced by an
authorised person.
Declaration of conformity
This appliance is intended to come into contact
with foodstuffs and conforms to D.L. 108 of
25.01.1992 (European Directive 89/109/EEC).
Information
Appliances with Isobutane (R600a)
Isobutane is a natural gas having low
environmental impact. Caution is required,
however, since isobutane is flammable.
Therefore, it is essential to ensure that
refrigerant pipelines are not damaged.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
1gb37030a.fm5 Page 13 Friday, February 9, 2001 7:50 PM
14
Switching on the appliance
Starting up the appliance
Depending on the model, the appliance is
equipped with
external controls
or
internal
controls
.
Plug in the appliance.
For appliances featuring
external controls
:
•
The light below the control panel switches on
each time the door is opened.
•
The green LED lights up, indicating the
appliance is operating.
For appliances featuring
internal controls
, when
the appliance is connected to the mains the inside
light switches on each time the door is opened
(provided the thermostat is not turned to
z
).
The thermostat, located inside the refrigerator
compartment or on the front panel, is used to
adjust the temperature of both the refrigerator
compartment and low temperature compartment
(if fitted).
Adjusting the temperature
1.
For correct operation and optimum storage of
food,
follow instructions given in the
enclosed product sheet for thermostat
adjustment.
2.
To adjust the temperature in the
compartment, turn the thermostat control
knob:
•
lowest numbers
1-2/MIN
for the
LEAST
COLD
internal temperatures;
•
numbers
3-4/MED
for a
MEDIUM internal
temperature;
•
highest numbers
5-7/MAX
for the
COLDEST
internal temperatures.
Thermostat set to
z
: all functions, including the
inside light, are switched off.
Note:
The ambient air temperature, frequency of door
opening and the position of the appliance can
affect internal temperatures. These factors must
be taken into account when setting the
thermostat.
How to use the refrigerator compartment
Position the food as shown in the figure.
A Cooked food
B Fish, meat
C Fruit and vegetables
D Bottles
E Cheese
Notes:
•
The space between the shelves and the rear
wall of the refrigerator compartment must be
unobstructed to allow circulation of air.
•
Do not place food in direct contact with the
rear wall of the refrigerator compartment.
•
Do not place hot food in the refrigerator.
•
Store liquids in closed containers.
Important
Storing vegetables with high water content
can cause condensation to form on the glass
shelf of the crisper drawer: this will not affect
the correct operation of the appliance.
.
HOW TO OPERATE THE REFRIGERATOR
COMPARTMENT
A
B
E
D
C
1gb37030a.fm5 Page 14 Friday, February 9, 2001 7:50 PM
15
The low temperature compartment is ,
or .
Compartments marked o can be
used to store frozen foods for the period of
time indicated on packaging. If the low
temperature compartment is marked , it
can also be used to freeze fresh food.
The quantity of fresh food that can be frozen
in 24 hours is shown on the rating plate.
Note:
In the event of a power cut, the low temperature
compartment will maintain a sufficiently low
temperature for food storage. However, it is
advisable to avoid opening the compartment
door during such periods.
Freezing fresh food (only in
compartments marked )
Important
•
Before freezing, wrap and seal fresh food in:
aluminium foil, cling film, air and water-tight
plastic bags, polythene containers with lids
or freezer containers suitable for freezing
fresh food.
•
Arrange the fresh food in the top
compartment, leaving sufficient space
around each pack for the air to circulate.
•
For optimum freezing, turn the thermostat
down by half a point when placing fresh foods
in the freezer compartment.
•
The food will be completely frozen in 24
hours.
For appliances with compartments marked
The table alongside shows the recommended
maximum storage time for frozen fresh foods.
When purchasing frozen food products:
•
Ensure that the packaging is not damaged
(frozen food in damaged packaging may
have deteriorated). If the package is swollen
or has damp patches, it may not have been
stored under optimal conditions and
defrosting may have already begun.
•
When shopping, leave frozen food
purchases until last and transport the
products in a thermally insulated cool bag.
•
Place the items in the low temperature
compartment as soon as you get home.
•
If food has defrosted even partially, do not re-
freeze it. Consume within 24 hours.
•
Avoid, or reduce temperature variations to
the minimum. Respect the best-before date
on the package.
•
Always observe the storage information on
the package.
Making ice cubes
•
Fill the ice cube tray 2/3 full and place it in the
low temperature compartment.
•
Do not use sharp or pointed instruments to
detach the tray if it is stuck to the low
temperature compartment bottom.
•
Bend the ice tray slightly to remove the
cubes.
.
HOW TO OPERATE THE LOW TEMPERATURE
COMPARTMENT
MONTHS FOOD
1gb37030a.fm5 Page 15 Friday, February 9, 2001 7:50 PM
16
Before any cleaning or maintenance
operation, unplug the appliance from the
mains or disconnect the electrical power
supply.
Defrosting of the refrigerator compartment is
completely automatic.
Droplets of water on the rear wall of the
refrigerator compartment indicate that the
periodic automatic defrost cycle is in progress.
The defrost water is automatically routed to a
drain outlet and into a container from which it
evaporates.
Clean the defrost water drain outlet regularly
using the tool supplied with the appliance in
order to ensure defrost water is removed
correctly.
Defrosting the low temperature compartment
Defrost the low temperature compartment
once or twice a year or when the ice
formation is excessive.
It is perfectly normal for ice to form. The
amount of ice which forms and the rate at
which it accumulates will depends on room
temperature and humidity, and on the
frequency with which the door is opened. Ice
formation is concentrated at the top of the
compartment and does not affect the
efficiency of the appliance.
If possible, carry out defrosting when the
compartment is nearly empty.
•
Remove the food from the low temperature
compartment, wrap in a newspaper and
group together in a cool place or in a portable
cooler.
•
Leave the door open to allow the frost to melt.
•
Clean the interior with a sponge soaked in
warm water and/or neutral detergent. Do not
use abrasive substances.
•
Rinse the interior and dry thoroughly.
•
Put the food back into the compartment.
•
Close the door.
•
Plug in the appliance once again.
•
Switch the appliance on.
HOW TO DEFROST AND CLEAN THE REFRIGERATOR
1gb37030a.fm5 Page 16 Friday, February 9, 2001 7:50 PM
17
•
Periodically clean air vents and the
condenser at the rear of the appliance with a
vacuum cleaner or a brush.
•
Clean the outside using a soft cloth.
Prolonged disuse
1.
Empty the refrigerator.
2.
Disconnect the appliance from the power
supply.
3.
Defrost and clean the interior.
4.
In the event of prolonged disuse, leave the
door open to prevent the formation of mould,
odours and oxidation.
5.
Clean the appliance.
•
Clean the inside of the low temperature
compartment (where fitted) when defrosting.
•
Periodically clean the inside of the
refrigerator compartment with a sponge
dampened in warm water and/or neutral
detergent. Rinse the interior and dry with a
soft cloth. Do not use abrasive products.
•
Clean the outside with a damp cloth. Do not
use abrasive products, scourers, stain-
removers (e.g. acetone, trichloroethylene) or
vinegar.
.
1. The appliance is not working.
•
Is there a power failure?
•
Is the plug properly inserted in the socket?
•
Is the double-pole switch on?
•
Has the fuse blown?
•
Is the power cord in perfect condition?
•
Is the thermostat set to
z
(Stop)?
2. Temperature inside the compartments is
not low enough.
•
Is the door shut properly?
•
Is food obstructing proper door closure?
•
Is the appliance installed near a heat
source?
•
Is the thermostat setting correct?
•
Are the air circulation vents blocked?
3. Temperature inside the refrigerator
compartment is too low.
•
Is the thermostat setting correct?
4. The appliance is excessively noisy.
•
Has the appliance been installed correctly?
•
Are the pipes at the back touching or
vibrating?
5. Water collects at the bottom of the
refrigerator compartment.
•
Is the defrost water drain blocked?
6. Excessive frost build-up in the low
temperature compartment.
•
Is the door shut properly?
•
Is food obstructing proper door closure?
Notes:
• Gurgling and hissing noises due to
expansion in the refrigerant circuit are
normal.
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
1gb37030a.fm5 Page 17 Friday, February 9, 2001 7:50 PM
18
Before contacting After-Sales Service:
1.
See if you can solve the problem yourself
with the help of the Trouble-shooting guide.
2.
Switch the appliance on again to see if the
problem has been solved. If it has not,
disconnect the appliance from the power
supply and wait for about an hour before
switching on again.
3.
If the problem persists after this course of
action, contact After-sales Service.
Specify:
•
the nature of the problem
•
the model
•
the Service number (the number after the
word SERVICE on the data plate on the
inside of the appliance)
•
your full address
•
your telephone number and area code
Note:
The direction of door opening can be
changed. If this operation is performed by
After-sales Service it is not covered by the
warranty.
•
Install the appliance away from heat sources.
Installation in a hot environment, direct
exposure to the sun or installation near heat
sources (heaters, radiators, cookers) will
increase power consumption and should
therefore be avoided.
•
If this is not possible, the following minimum
distances must be respected:
•
30 cm from coal or paraffin stoves;
•
3 cm from electric and/or gas stoves.
•
Fit the spacers on the rear of the condenser
positioned at the back of the appliance (see
figure).
•
To optimize appliance efficiency, leave a 5
cm gap above the appliance and make sure
that adjacent kitchen units are sufficiently
distanced to allow air circulation.
•
Install the appliance in a dry, well-ventilated
place, and ensure it is level, using the front
adjustment feet if necessary.
•
Clean the interior.
•
Fit the accessories.
Electrical connection
• Electrical connections must be made in
accordance with local regulations.
•
Voltage and power consumption are
indicated on the rating plate inside the
appliance.
• Regulations require that the appliance is
earthed.
The manufacturer declines all liability for
injury to persons or animals and for
damage to property resulting from failure
to observe the above procedures and
reminders.
•
If the plug and socket are not of the same
type, have the socket replaced by a qualified
electrician.
•
Do not use extension leads or adaptors.
Disconnecting the appliance
It must be possible to disconnect the appliance
by unplugging it or by means of a two-pole switch
fitted upline of the socket.
AFTER-SALES SERVICE
INSTALLATION
1gb37030a.fm5 Page 18 Friday, February 9, 2001 7:50 PM
19
For Great Britain only
Warning
- this appliance must be
earthed
Fuse replacement
If the mains lead of this appliance is fitted with a
BS 1363A 13amp fused plug, to change a fuse in
this type of plug use an A.S.T.A. approved fuse
to BS 1362 type and proceed as follows:
1.
Remove the fuse cover (A) and fuse (B).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a
fuse and if the fuse cover is lost the plug must not
be used until a correct replacement is fitted.
Correct replacement are identified by the colour
insert or the colour embossed in words on the
base of the plug.
Replacement fuse covers are available from
your local electrical store.
Connection to a rewirable plug
If the fitted plug is not suitable for your socket
outlet, then it should be cut off and disposed of in
order to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
A suitable alternative plug should then be fitted
to the cable.
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
1.
The GREEN AND YELLOW wire must be
connected to the terminal in the plug which is
marked with the letter “E” or by the Earth
symbol or coloured green or green and
yellow.
2.
The BLUE wire must be connected to the
terminal which is marked with the letter “N” or
coloured black.
3.
The BROWN wire must be connected to the
terminal which is marked with the letter “L” or
coloured red.
For the Republic of Ireland only
•
The information given in respect of Great
Britain will frequently apply, but a third type of
plug and socket is also used, the 2-pin, side
earth type. In this case, the wire which is
coloured GREEN AND YELLOW must be
connected to the EARTH contact, and the
two wires to the two pins, irrespective of
colour. The supply to the socket must be
fitted with a 16 amp fuse.
ELECTRICAL CONNECTION
1gb37030a.fm5 Page 19 Friday, February 9, 2001 7:50 PM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool ART 561/H User guide
-
Whirlpool ART 942/G User guide
-
Viking UVI 1302/A Owner's manual
-
Ignis NC 1838 W User guide
-
NEUTRAL ARL 632/G/N-RF46 User guide
-
Whirlpool ART 945/G User guide
-
-
Viking ART 632/H User guide
-
Whirlpool KVIE 1309/1/A User guide
-
Whirlpool ART 536/G Owner's manual