Whirlpool WHD3090GW Dimensions Guide

Brand: Whirlpool

Model: WHD3090GW

Type: Dimensions Guide

Heat Pump Dryer

PRODUCT MODEL NUMBERS

W10858718B

11/2016

WHD3090G WHD5090G

DRYER DIMENSIONS

/2" Min.

(851 mm)

/4" Max.

(857 mm)

24"

(610 mm)

Front view:

24"

(610 mm)

⁄2" Min.

(851 mm)

⁄2" Max.

(876 mm)

Side view:

Back view:

/4 "

(184 mm)

(102 mm)

/4"

(18 mm)

NOTES:

■ Allow clearance

behind dryer for

proper drain hose

routing and cooling

fan ventilation. Push

dryer back as far as

possible and make

sure drain hose

is not crushed

or kinked.

■ Water can be

drained into an

alternate location.

Remove the top

end of the white

hose from the water

tank and install,

for example, in

a ﬂoor standpipe

(see “Drain System”).

Grey

water

drain

Cooling

fan

IMPORTANT: Do not block cooling fan as your dryer may not

operate properly.

Power cord/

cable

/2"

(1054 mm)

24"

(610 mm)

/4"

(18 mm)

⁄16"

(1100 mm)

26"

(654 mm)

White

hose from pump

to water tank

Installation spacing for recessed area

or closet installation

All dimensions show recommended and minimum spacing

allowed.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door,

ﬂoor, moldings, and drain system.

■ Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

■ For closet installation with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■ Companion appliance spacing should also be considered.

Recommended installation clearances (dryer only):

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile

home construction and Safety, Title 24, HUD Part 280)

or Standard CAN/CSA-Z240 MH.

18" min.

(457 mm)

(25 mm)

0" - 5"*

(0 mm - 127 mm)

24 in.

min.

(155 cm

)

48 in.

min.

(310 cm

)

(76 mm)

(25 mm)

*NOTE: 0"–5"

(0 mm–127 mm)

spacing is allowed

behind dryer, providing

drain hose is not kinked

or pinched.

Minimum diameter for a standpipe drain: 2" (51 mm). Top of

standpipe must be at least 30" (762 mm) high; install no higher

than 36" (910 mm) from bottom of dryer.

Floor standpipe drain system

Drain system can be installed by routing the white hose to

a ﬂoor drain, wall standpipe, ﬂoor standpipe, or laundry tub

instead of to the water tank. Select the method you need.

IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain

hose should be inside standpipe; do not force excess hose

into standpipe. Always secure drain hose with a cable tie

(not supplied).

4.5"

(114 mm)

4.5"

(114 mm)

max. 48"

(1219 mm)

min. 30"

(762 mm)

Custom under-counter installation:

⁄2" Min.

(876 mm)

1" Min.

(25 mm)

1" Min.

(25 mm)

max. 36"

(910 mm)

min. 30"

(762 mm)

0" Min.

(0 mm)

DRAIN SYSTEM

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation

our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.

To supply the required 3- or 4-wire, single-phase, 120-/240-volt, 60 Hz., AC-only electrical supply (or 3- or 4-wire, 120-/208-volt

electrical supply, if specied on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay

fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

Do not use an extension cord.

ELECTRICAL REQUIREMENTS