BMW DWA 5 User manual

1

BMW Motorrad

Supplementary Rider’s Manual

DWA 5 Anti-Theft Alarm System

DWA_5_2_eng.book Seite 41 Dienstag, 1. März 2005 4:59 16

d Warning:

This symbol indicates pre-

cautions and measures which

are essential in order to pro-

tect the rider and other per-

sons from possibly severe or

fatal injury.

e Attention:

Special instructions and

precautions intended to avoid

damage to the motorcycle.

Non-compliance can void the

guarantee.

L Note:

Specific instructions on how to

operate, control, adjust or look

after items of equipment on the

motorcycle.

Note:

DWA_5_2_eng.book Seite 42 Dienstag, 1. März 2005 4:59 16

1

Details described or illustrated

in this booklet may differ from

the motorcycle’s actual specifi-

cation as purchased, the

accessories fitted or the

national-market specification.

No claims will be entertained as

a result of such discrepancies.

Dimensions, weights, fuel con-

sumption and performance

data are quoted to the custom-

ary tolerances.

The right to modify designs,

equipment and accessories is

reserved.

Errors and omissions excepted.

Not to be reproduced either

wholly or in part without written

permission from

BMW Motorrad, After Sales.

Printed in Germany

DWA_5_2_eng.book Seite 43 Dienstag, 1. März 2005 4:59 16

BMW Motorrad

Order No.:

01 41 7 695 361

01.2005

2nd edition GB / RF

The Ultimate

Driving Machine

BMW recommends Castrol

DWA_5_2_eng.book Seite 44 Dienstag, 1. März 2005 4:59 16

1

Introduction

i

Welcome to BMW

Congratulations on your pur-

chase of this BMW anti-theft

alarm.

It acts as a deterrent for poten-

tial thieves, while at the same

time being easy and straightfor-

ward to use.

Your authorised BMW motorcy-

cle dealer will be glad to assist

you in all matters relating to

your motorcycle.

We hope you will enjoy familiar-

ising yourself with these

instructions for use, and we

would like to take this opportu-

nity of sending you our very

best wishes.

Yours sincerely,

BMW Motorrad

Welcome to BMW

DWA_5_2_eng.book Seite 1 Dienstag, 1. März 2005 4:59 16

2

Introduction

i

i Introduction

Welcome to BMW ................. 1

General ................................. 3

1 Overview and operation

Controls ................................ 4

Functions of the remote

control unit............................ 5

Code card ............................. 6

2 Immobiliser

Activation .............................. 7

Deactivation .......................... 9

3 Alarm function

Activation ............................ 10

Activation phases................ 12

How the alarm is

triggered ............................. 13

Deactivation ........................ 14

Reasons for an alarm .......... 16

4 Central locking system

Manual operation ................ 19

Remote control unit............. 20

Emergency unlocking.......... 21

Safety shutdown ................. 22

5 Lights

Lights.................................. 23

6 Programming

Customising the anti-theft

alarm system ...................... 24

Default settings ................... 25

Accessing the

programming mode ............ 26

Programming ...................... 27

Exiting

programming mode ............ 28

7 Remote control units

Registering remote

control units ........................ 29

Exiting registration mode .... 32

Synchronising the

remote control unit.............. 33

8 Care and maintenance

Changing the battery .......... 34

9 Technical data

Technical data .................... 36

i Index

Index................................... 37

Contents

DWA_5_2_eng.book Seite 2 Dienstag, 1. März 2005 4:59 16

3

Introduction

i

Any attempt to move the motor-

cycle, change its position, start

it without your permission, or

disconnect the battery will trig-

ger the alarm. The sensitivity of

the system is set in such a way

that slight vibrations of the

motorcycle will not trigger a

false alarm.

Once you have activated the

alarm, any attempted theft is

indicated acoustically by the

siren and visually by all four turn

indicators flashing at the same

time, and the integrated immo-

biliser suppresses engine start.

Your anti-theft alarm is com-

bined with a central locking sys-

tem that enables you to open

and close the cases, the top-

case, and the radio compart-

ment by remote control.

It also enables you to switch on

the map-reading light and the

ground lights automatically.

You can customise the anti-

theft alarm in certain ways to

suit your needs and prefer-

ences.

L Note:

In order to protect the motorcy-

cle’s battery and ensure that

the engine can be started, the

alarm system deactivates itself

automatically a certain number

of days after being activated, al-

though it always remains active

for at least 7 days.

General

DWA_5_2_eng.book Seite 3 Dienstag, 1. März 2005 4:59 16

4

Overview and operation

1

1 Left button (ribbed)

2 Right button

3 LED

4 Radio remote control unit

5 Status LED

(on the vehicle)

L Note:

Do not be tempted to use the

remote control unit to lock the

keys inside a stowage compart-

ment. If you were to mislay the

remote control unit the keys

would be inaccessible and you

would be able neither to open

the cases by means of the

emergency unlocking routine

nor to deactivate the electronic

immobiliser.

Controls

1

4

5

2

3

DWA_5_2_eng.book Seite 4 Dienstag, 1. März 2005 4:59 16

5

Overview and operation

1

Functions of the remote control unit

Operation Button 1 Confirmation

Press once Lock central locking –

Press again Activate alarm func-

tion and immobiliser

Turn indicators flash

2x Alarm tone

sounds 2x (if pro-

grammed)

Press for third time Deactivate motion

sensor (for transport,

for example)

Indicators flash 3x

Alarm tone sounds

3x

Operation Button 2 Confirmation

Press once Deactivate alarm

function and immo-

biliser, unlock cen-

tral locking

Indicators flash 1x

Alarm tone sounds

1x (if programmed)

Press again – –

Press for third time – –

L Note:

The signals from your remote

control unit could be disrupted by

interference from other radio sys-

tems or devices transmitting on

the same frequency.

If you encounter this problem, try

pointing the remote control unit at

the motorcycle from a different di-

rection.

DWA_5_2_eng.book Seite 5 Dienstag, 1. März 2005 4:59 16

6

Overview and operation

1

Code card

The anti-theft alarm is supplied

complete with a sealed enve-

lope containing a code card 1.

The number stated on the code

card (remove the adhesive

label) is the code for deactivat-

ing the anti-theft alarm by

means of the ignition (

b 17).

It is advisable to keep the code

card with the vehicle registra-

tion papers, and carry both with

you when you ride the motorcy-

cle.

The code number is stamped in

encrypted form on the anti-theft

alarm and it is also printed on

an adhesive label 2 supplied

with the anti-theft alarm. You

should affix the label at a con-

cealed location on the motorcy-

cle.

If you forget the code and are

unable to find the code card, an

authorised BMW motorcycle

dealer will be able to forward

the encrypted number to BMW

on your behalf and obtain the

correct code.

2

1

DWA_5_2_eng.book Seite 6 Dienstag, 1. März 2005 4:59 16

7

Immobiliser

2

Once the immobiliser has been

activated the engine will refuse

to start even if an authorised

key is used for the start

attempt. You can tell whether

the immobiliser is activated by

switching on the ignition and

observing LED 5; if the immobi-

liser is active it will light up when

the pre-ride check completes.

L Note:

The remote control unit acti-

vates both the immobiliser and

the alarm function.

It is also possible to have the

immobiliser activated automati-

cally when the ignition is

switched off (default) without

activation of the alarm function

(

b 26).

Activation

The immobiliser is activated

• by pressing button 1 on the

remote control unit twice

(alarm function is also acti-

vated)

or

• by switching off the ignition, if

programmed (

b 26)

When you switch off the igni-

tion, 50 seconds elapse before

the activation phase.

Activation

1 2

5

DWA_5_2_eng.book Seite 7 Dienstag, 1. März 2005 4:59 16

8

Immobiliser

2

Activation

Activation of the immobiliser

after ignition off but without

activation of the alarm function

is confirmed

• by the turn indicators flashing

once

and

• by the alarm tone sounding

once, if programmed (

b 26)

Activation of the immobiliser

with activation of the alarm

function by means of the

remote control unit is confirmed

• by the indicators flashing

twice

and

• by the alarm tone sounding

twice, if programmed (

b 26)

If confirmation takes the form of

the alarm tone sounding four

times, this is to indicate that the

anti-theft alarm's internal

rechargeable battery is dis-

charged. The rechargeable bat-

tery of the anti-theft alarm is

charged through the on-board

electrical system, which means

that this problem might be due

to a discharged starter battery.

When the anti-theft alarm's

internal battery is discharged

the alarm will not be triggered

by an attempt to disconnect the

starter battery.

Contact your authorised BMW

motorcycle dealer if the alarm

tone sounds four times on acti-

vation even after a lengthy jour-

ney.

DWA_5_2_eng.book Seite 8 Dienstag, 1. März 2005 4:59 16

9

Immobiliser

2

Deactivation

Deactivating the immobi-

liser with the remote con-

trol unit

The immobiliser is deactivated

• by pressing button 2 on the

remote control unit once (if

the immobiliser was activated

automatically beforehand

when you switched off the

ignition, it is reactivated

30 seconds later).

Deactivation is confirmed

• by the turn indicators flashing

once

and

• by the alarm tone sounding

once, if programmed (

b 26)

If confirmation takes the form of

the alarm tone sounding four

times, this is to indicate that the

voltage in the on-board elec-

tricity supply has dropped

below a predefined threshold.

In this case, recharge the

motorcycle's starter battery

(

b Rider's Manual).

Deactivating the immobi-

liser without the remote

control unit

The procedure is the same as

that for deactivating the alarm

function without the remote

control unit (

b 15).

1 2

DWA_5_2_eng.book Seite 9 Dienstag, 1. März 2005 4:59 16

10

Alarm function

3

Activation with motion

sensor

The alarm function is activated

• by pressing button 1 on the

remote control unit twice

or

• by switching off the ignition, if

programmed (

b 25)

When you switch off the igni-

tion, 50 seconds elapse before

activation.

The central locking system is

not activated.

Activation is confirmed

•by the indicators flashing

twice

and

• by the alarm tone sounding

twice, if programmed (

b 26)

Activation

1 2

DWA_5_2_eng.book Seite 10 Dienstag, 1. März 2005 4:59 16

3

11

Alarm function

Activation

Deactivating the motion

sensor

If, for example, you want to

transport your motorcycle by

train, it is advisable to deacti-

vate the motion sensor. Severe

movements while the motorcy-

cle is in transit could trigger a

false alarm.

You deactivate the motion sen-

sor

• by pressing button 1 on the

remote control unit for a sec-

ond time within the activation

phase (

b 12)

Deactivation is confirmed

• by the indicators flashing

three times

and

• by the alarm tone sounding

three times

DWA_5_2_eng.book Seite 11 Dienstag, 1. März 2005 4:59 16

12

Alarm function

3

Activation phases

15 seconds elapse before the

alarm function is fully active.

Status of the anti-

theft alarm

LED

Activation phase

(15 seconds)

Rapid flashing

(0.1 sec. on/ 0.5 sec. off)

If the motion sensor was switched off:

Rapid flashing

(0.1 sec. on/ 0.2 sec. off)

Anti-theft alarm

active

Slow flashing

(0.1 sec. on/ 0.9 sec. off)

dwa_3_alarmfunktion_eng.fm Seite 12 Donnerstag, 10. März 2005 11:04 11

3

13

Alarm function

How the alarm is triggered

The alarm can by triggered

• by the motion sensor

• by an attempt to switch on the

ignition without deactivating

the anti-theft alarm before-

hand

• by disconnection of the anti-

theft alarm from the motorcy-

cle's battery (the anti-theft

alarm's internal battery cuts in

to supply power)

Alarm

An alarm lasts for 26 seconds.

The alarm function is active

again 12 seconds later. If the

reason for the alarm persists,

the alarm function is triggered

again, but this can happen no

more than five times in succes-

sion. You can cancel an alarm

at any time after it has been trig-

gered by pressing button 2 on

your remote control unit. This

function does not change the

status of the anti-theft alarm.

An acoustic alarm sounds and

the turn indicators flash for the

duration of the alarm. You can

program the sound of the

acoustic alarm (

b 26).

1 2

DWA_5_2_eng.book Seite 13 Dienstag, 1. März 2005 4:59 16

14

Alarm function

3

Deactivation

Deactivating the alarm

function with the remote

control unit

The alarm function is deacti-

vated

• by pressing button 2 on the

remote control unit once

If the alarm function was acti-

vated automatically beforehand

when you switched off the igni-

tion, it is reactivated 30 sec-

onds later.

Deactivation is confirmed

• by the turn indicators flashing

once

and

• by the alarm tone sounding

once, if programmed (

b 26)

1 2

DWA_5_2_eng.book Seite 14 Dienstag, 1. März 2005 4:59 16

3

15

Alarm function

Deactivation

Deactivating the alarm

function without remote

control unit

If you do not have the remote

control unit to hand when the

anti-theft alarm is active, you

can still deactivate the system.

To do so, you will need the

code number printed on your

code card (

b 6).

Deactivation is confirmed

• by the turn indicators flashing

once

and

• by the alarm tone sounding

once, if programmed (

b 26)

L Note:

The system will permit a maxi-

mum of 3 successive attempts;

if the third attempt in succes-

sion is unsuccessful the anti-

theft alarm engages for 10 min-

utes. The cases remain locked

when the system is deactivated

without the remote control unit.

In this case you will have to re-

sort to the emergency unlock-

ing routine (

b 21).

Step Action Confirmation

1 Switch on the ignition Alarm is triggered

2 Switch off the ignition and

observe the LED

LED flashing,

alarm continues

3 Count the LED flashes until the

number corresponds to the first

digit of your code number.

4 Switch on the ignition while the

LED is on

LED OFF

5 Repeat steps

2 to 4 for each successive digit

in your code number

DWA_5_2_eng.book Seite 15 Dienstag, 1. März 2005 4:59 16

16

Alarm function

3

Reasons for an alarm

Once you have deactivated the

alarm function, the LED shows

you reasons for alarms, if any,

that were triggered in your

absence:

• Flashes 1x:

Motion sensor

• Flashes 2x:

Ignition on while the anti-theft

alarm was primed

• Flashes 3x:

Anti-theft alarm disconnected

from motorcycle battery

The LED ceases to output this

signal after 1 minute, or as soon

as you switch on the ignition.

If more than one alarm was trig-

gered, the flashing codes indi-

cate all the reasons.

DWA_5_2_eng.book Seite 16 Dienstag, 1. März 2005 4:59 16

Page is loading ...

BMW DWA 5 User manual

BMW DWA 5 User manual

Related papers

Other documents