Sauder 413118 Operating instructions

PLEASE CONTACT US

BEFORE RETURNING

YOUR UNIT TO THE STORE

1-800-523-3987

www.sauder.com

Made in the USA

Archbold, OH

NOTE: THIS INSTRUCTION BOOKLET CONTAINS

IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Lot #: 354641 07 / 10 / 13

Date Purchased: ____________________

413118

Starter Kit

Hanover Closets Collection

English .................... Page 1-20

Français ...............Pages 21-23

Espanol .............Páginas 24-27

ASSEMBLY TOOLS REQUIRED

Hammer

Tip Shown Actual Size

No. 2 Phillips Screwdriver

TABLE OF CONTENTS

Part Identiﬁ cation .......................3

Hardware Identiﬁ cation ......... 3-4

Assembly Steps .................... 5-20

Français .............................. 21-23

Espanol ............................... 24-27

Safety ................................. 28-30

Warranty ...................................31

Pencil

This product must be securely attached to a wall or building structural support. This product is not intended to function as a

stand--alone, unsupported piece of furniture. Failure to properly install this product will result in product collapse or tip--

over. Serious injury or damage can occur. Pay careful attention to all assembly and installation instructions. In particular:

• The product should be attached to a wall stud whenever possible.

• Drywall attachment hardware is provided. If attaching the product to a wall made of concrete, plaster, or other material,

you must obtain the appropriate mounting hardware from a local hardware store. The attachment hardware must be rated to

provide a minimum of 50 pounds of pull strength.

WARNING

Ce produit doit être fermement attaché à un mur ou on support de structure de construction. Ce produit n’est

pas prévu pour fonctionner comme meuble autonome, autostable. Une mauvaise installation de ce produit

provoquera l’effondrement ou le basculement du produit. De graves blessures corporelles ou dommages

peuvent se produire. Faire extrêmement attention à toutes les instructions de montage et d’installation.

En particulier :

• Le produit doit être attaché à un poteau mural dans la mesure du possible.

• Une quincaillerie de ﬁ xation sur cloison sèche est fournie. Si le produit est ﬁ xé sur un mur en béton, en

plâtre ou tout autre matériau, il faut obtenir la quincaillerie de montage appropriée auprès d’un quincaillier

local. La quincaillerie de ﬁ xation doit être qualiﬁ ée pour fournir un minimum de 22,6 kg de force

d’arrachage.

AVERTISSEMENT

Se requiere que este producto esté ﬁ jado con seguridad a una pared o a un soporte estructural del ediﬁ cio. Este

producto no está diseñado para estar colocado solo, como unidad mobiliario sin apoyo. El fallo de instalar este

producto adecuadamente resultará en el derrumbe del producto o su caída. Puede producir una grave lesión o

un serio daño. Preste cuidadosa atención a todas las instrucciones de ensamblaje e instalación.

En particular:

• El producto debe estar ﬁ jado a un montante de pared siempre que sea posible.

• Se provee el herraje para ﬁ jación a una pared mampostería. Si se ﬁ je el producto a una pared en concreto,

yeso u otro material, se requiere que obtenga el herraje de montaje apropiado de una ferretería local. El herraje

de ﬁ jación debe ser clasiﬁ cado para proveer una resistencia mínima a la tracción de 22.6 kg.

ADVERTENCIA

Tape Measure

Page 2 www.sauder.com/services 413118

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked

letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help

identify similar parts.

A RIGHT END 2

B LEFT END 2

C TOP 1

D FIXED SHELF 2

E SHELF 1

F BACK 2

G DRAWER FRONT 1

H DRAWER BACK 1

D239 DRAWER SIDE 2

J DRAWER BOTTOM 1

K BRACE 2

L ADJUSTABLE SHELF 2

M TOP MOLDING 1

A

B

C

D

E

F

G

H

J

K

L

M

BLACK 9/16" FLAT HEAD SCREW - 12ROD - 3 ROD HANGER - 6

CLOSET ROD KIT - 1

N

HARDWARE IDENTIFICATION

UPPER SECTION

LOWER SECTION

DRAWER

Page 3

www.sauder.com/services413118

D239

HARDWARE IDENTIFICATION

Screws are shown actual size. You may receive extra hardware with your unit.

Y

SAFETY BRACKET - 4

R

PROPEL NUT - 4

X

BLACK 9/16" LARGE HEAD SCREW - 14

DD

HOLE PLUG - 10

W

BLACK 1-7/8" FLAT HEAD SCREW - 10

CC

RUBBER SLEEVE - 8

U

CAM DOWEL - 16

O2

HIDDEN CAM - 16

P2

WALL ANCHOR - 10

S

ADJUSTABLE GLIDE - 4

T

NAIL - 64

GG

METAL PIN - 20

V

TIE PLATE - 2

Z

ANGLE BRACKET - 3

Q

GOLD 5/16" FLAT HEAD SCREW - 8

EE

CLIP - 4

PULL- 1

AA

35DA

CABINET RIGHT - 1

35DB

CABINET LEFT - 1

35DC

DRAWER RIGHT - 1

35DD

DRAWER LEFT - 1

DRAWER FRONT BRACKET - 1

BB

Page 4 www.sauder.com/services 413118

BROWN 7/16" LARGE HEAD SCREW - 4

HH

SILVER 1/2" MACHINE SCREW - 2

FF

WASHER - 2

II

1

S

t

e

p

Assemble your unit on a carpeted ﬂ oor or on the empty carton to avoid scratching your unit or the ﬂ oor.

Push sixteen HIDDEN CAMS (P2) into the ENDS (A and B), and FIXED SHELVES (D). Then, insert the metal end of a CAM

DOWEL (O2) into each HIDDEN CAM.

Do not tighten the HIDDEN CAMS in this step.

(16 used)

A

B

D

Page 5

www.sauder.com/services413118

Look for this icon. It means a video

assembly tip is available at:

www.sauder.com/services/tips

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

P2

O2

Arrow

O2

P2

(16 used)

2

S

t

e

p

35DA

35DB

You have the option to fasten the CABINET RAILS to the top position (as shown), middle position or lower position on the ENDS (A

and B).

Fasten the CABINET RIGHT (35DA) and CABINET LEFT (35DB) to one of each END (A and B). Use four GOLD 5/16" FLAT

HEAD SCREWS (EE).

See the DRAWER KIT 068-1672 instruction book for fastening CABINET RAILS to these optional holes.

GOLD 5/16” FLAT HEAD SCREW

(4 used in this step)

EE

Middle Rail option

Roller end

A

B

Lower Rail option

Middle Rail option

Roller end

Lower Rail option

Page 6 www.sauder.com/services 413118

3

S

t

e

p

Fasten the FIXED SHELF (D) to the LEFT END (B). Tighten two HIDDEN CAMS.

Insert four METAL PINS (V) into the ends of the BRACE (K).

Insert the METAL PINS (V) in one end of the BRACE (K) into the holes in the LEFT END (B).

Repeat this step for the LOWER SECTION.

B

D

V

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

K

Finished edge

Finished

UPPER SECTION

LOWER SECTION

Page 7

www.sauder.com/services413118

Caution

Risk of damage or

injury. Hidden Cams

must be completely

tightened. Hidden

Cams that are not

completely tightened

may loosen, and parts

may separate.

To completely tighten:

Start Tighten

Arrow

Maximum

210 degrees

Minimum

190 degrees

Arrow

4

S

t

e

p

Fasten the RIGHT END (A) to the FIXED SHELF (D) and BRACE (K). Tighten two HIDDEN CAMS.

NOTE: Be sure the PINS in the BRACE insert into the holes in the END.

Repeat this step for the LOWER SECTION.

D

K

A

Finished edge

UPPER SECTION

LOWER SECTION

Page 8 www.sauder.com/services 413118

Maximum

210 degrees

Minimum

190 degrees

Arrow

5

S

t

e

p

Fasten the TOP (C) to the ENDS (A and B) without the CABINET RAILS. Tighten four HIDDEN CAMS.

Fasten the SHELF (E) to the ENDS (A and B) with the CABINET RAILS. Tighten four HIDDEN CAMS.

A

B

E

C

Finished edge

UPPER SECTION

LOWER SECTION

Page 9

www.sauder.com/services413118

Maximum

210 degrees

Minimum

190 degrees

Arrow

6

S

t

e

p

Carefully turn your unit over onto its front edges. Unfold the BACKS (F) and lay them over the UPPER and LOWER SECTIONS.

Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”.

Fasten the BACKS (F) to the UPPER and LOWER SECTIONS using the NAILS (GG).

Use a hammer to drive a PROPEL NUT (X) into the holes in the ENDS (A and B) in the LOWER SECTION with CABINET RAILS.

Now, turn an ADJUSTABLE GLIDE (T) clockwise completely into each PROPEL NUT.

X

T

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

NAIL

(60 used in this step)

GG

Unﬁ nished surface

F

UPPER SECTION

LOWER SECTION

A

B

Page 10 www.sauder.com/services 413118

7

S

t

e

p

UPPER SECTION

Carefully turn the UPPER SECTION on its TOP (C).

Fasten three ANGLE BRACKETS (Q) to the ENDS (A and B) and TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (DD).

NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and TOP.

Fasten the TOP MOLDING (M) to the ENDS (A and B) and TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (DD).

BLACK 9/16” LARGE HEAD SCREW

(6 used for the ANGLE BRACKETS)

DD

M

Q

A

B

C

Wider edge

Page 11

www.sauder.com/services413118

8

S

t

e

p

Pull the DRAWER FRONT BRACKETS (BB) apart and slide them into the grooves in the DRAWER SIDES (D239). You may need

to gently tap them in with a hammer.

NOTE: The DRAWER FRONT BRACKETS are marked “RH” and “LH” for easy identification.

Fasten the DRAWER FRONT (G) to the DRAWER FRONT BRACKETS (BB). Use four BLACK 7/16" LARGE HEAD SCREWS (HH).

Slide the DRAWER BOTTOM (J) into the grooves in the DRAWER SIDES (D239) and DRAWER FRONT (G).

Pull the BRACKETS apart

and slide them into the

DRAWER SIDE grooves.

Unﬁ nished

With the palm of your hand, tap the

DRAWER BOTTOM down into the groove.

Groove

1

st

2

nd

BB

G

J

G

BB

Page 12 www.sauder.com/services 413118

BROWN 7/16” LARGE HEAD SCREW

(4 used for the BRACKETS)

HH

D239

9

S

t

e

p

Slide the DRAWER BACK (H) into the grooves in the DRAWER SIDES (D239).

Flip the drawer over and insert four CLIPS (Y) into the groove in the DRAWER BACK (H) and wrap them over the DRAWER

BOTTOM (J). Tap a NAIL (GG) through each CLIP.

NOTE: The CLIPS should set in about 1” from the DRAWER SIDES.

1

st

2

nd

Slide the DRAWER BACK down.

NAIL

(4 used in this step)

Groove

GG

H

Y

J

H

Page 13

www.sauder.com/services413118

D239

10

S

t

e

p

35DC

35DD

Fasten the DRAWER RIGHT (35DC) and DRAWER LEFT (35DD) to the DRAWER SIDES (D239). Use four GOLD 5/16" FLAT

HEAD SCREWS (EE).

GOLD 5/16” FLAT HEAD SCREW

(4 used in this step)

EE

Roller end

Page 14 www.sauder.com/services 413118

D239

Fasten the PULL (AA) to the DRAWER FRONT (G). Use two SILVER 1/2" MACHINE SCREWS (FF) through the WASHERS (II)

and into the PULL (AA).

11

S

t

e

p

AA

G

Page 15

www.sauder.com/services413118

SILVER 1/2" MACHINE SCREW

(2 used in this step)

FF

II

(2 used)

Carefully stand your sections upright and move them close to the wall.

Insert four METAL PINS (V) into the holes in the SHELF (E) of the LOWER SECTION. With someone's help, place the UPPER

SECTION on top of the LOWER SECTION.

NOTE: Be sure the pins in the LOWER SECTION insert into the holes in the ENDS (A and B) of the UPPER SECTION.

Push ten HOLE PLUGS (W) into the front unused CABINET RAIL holes in each END (A and B).

NOTE: Do not plug the holes for the CABINET RAILS in the lower section, if you purchased extra DRAWER KITS 068-1672.

12

S

t

e

p

V

UPPER SECTION

LOWER SECTION

E

A

B

W

(10 used)

Page 16 www.sauder.com/services 413118

13

S

t

e

p

Fasten two TIE PLATES (Z) to the back edges of the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (DD).

With someone's help, move the unit against the closet back wall near its final position.

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

DD

B

A

Z

UPPER SECTION

LOWER SECTION

Page 17

www.sauder.com/services413118

Minimum diistance 27"

Maximum distance 47.5"

14

S

t

e

p

IMPORTANT: If you are attaching the CLOSET ROD KIT to this unit and to a side wall, the unit must be 27"- 47.5" from the side wall.

NOTE: Be sure the unit is level. If it is not, make adjustments by turning the ADJUSTABLE GLIDES counter-clockwise to lower the

unit and clockwise to raise the unit.

Locate and mark the wall stud locations on your wall. If you cannot locate a stud in your wall, skip over the next paragraph to the

WALL ANCHOR installation.

Use a BLACK 9/16" LARGE HEAD SCREW (DD) into the top of the unit and a BLACK 1-7/8" PAN HEAD SCREW (CC) into the

stud in your closet wall. Be sure to allow the distance of any baseboards in your closet. There are no holes provided in the unit to attach

the SAFETY BRACKET (R). Use a little extra force while turning the BLACK 9/16" LARGE HEAD SCREW (DD) into the TOP (C).

WALL ANCHOR INSTALLATION

While holding the SAFETY BRACKET (R) against the wall directly above the TOP (C), mark with a pencil the location through the

hole in the SAFETY BRACKET onto the wall to drill for the WALL ANCHOR (S).

On the marked location, drill a 1/4" hole into the wall. Turn the WALL ANCHOR (S) into the hole until it is flush. Next position the

SAFETY BRACKET over the WALL ANCHOR and turn the BLACK 1-7/8"FLAT HEAD SCREW (CC) into the WALL ANCHOR.

Be sure to allow the distance of any baseboards in your closet. There are no holes provided in the top of the unit. Use a little extra

force while turning the BLACK 9/16" LARGE HEAD SCREW (DD) through the BRACKET and into the TOP.

Repeat this step to fasten the remaining SAFETY BRACKETS along the top of the UPPER SECTION and ENDS of the LOWER

SECTION.

R

Use WALL ANCHOR only if you

can not locate a stud in the wall.

S

R

CC

DD

Use WALL ANCHOR only if you

can not locate a stud in the wall.

C

Page 18 www.sauder.com/services 413118

Unpack the CLOSET KIT (N).

Fasten a ROD HANGER to your unit at the desired height and 8-3/4" from the screw hole to the wall. Use two BLACK 9/16" FLAT

HEAD SCREWS provided in the CLOSET KIT (N).

Fasten another ROD HANGER to the side wall at the same height off the floor and distance away from the back wall that you fastened

the first ROD HANGER to your unit.

While holding the ROD HANGER in the correct location on the wall, place a mark onto the side wall with your pencil through the two

holes in the ROD HANGER.

On the marked locations, drill a 1/4" hole into the wall. Turn two WALL ANCHORS (S) into the holes until it is flush. Next position

the ROD HANGER over the two WALL ANCHORS and turn two BLACK 1-7/8" SCREWS (CC) through the ROD HANGER and

into the WALL ANCHORS.

Place the RODS onto the ROD HANGERS by inserting the holes in the ends of the RODS over the posts on the ROD HANGERS.

Pull down firmly.

Repeat this step to fasten and hang the remaining RODS in the CLOSET KIT.

15

S

t

e

p

Use WALL ANCHORS

only if you can not locate

a stud in the wall.

Hole

Post

8-3/4

"

8-3/4

"

CLOSET ROD KIT

N

S

CC

Page 19

www.sauder.com/services413118

16

S

t

e

p

Push the RUBBER SLEEVES (U) over the METAL PINS (V). Insert the METAL PINS into the hole locations of your choice in the

ENDS (A and B). Set the ADJUSTABLE SHELF (L) onto the METAL PINS.

To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit.

Lift the front of the drawer up and slide it into the unit.

See the DRAWER KIT #412914 and SHELF KIT #412913 instruction book for fastening them to the STARTER KIT.

NOTE: Please read the back pages of the instruction booklet for important safety information.

This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.

L

Place the roller on the SLIDE

behind the roller on the RAIL.

25 lbs.

20 lbs.

30 lbs.

25 lbs.

15 lbs.

50 lbs.

U

V

(8 used)

A

B

L

Page 20 www.sauder.com/services 413118

Page is loading ...

Sauder 413118 Operating instructions

Sauder 413118 Operating instructions

in other languages

Related papers

Other documents