Hitachi CMPAK345 Installation Instructions Manual

Brand: Hitachi

Model: CMPAK345

Type: Installation Instructions Manual

Hitachi Plasma Screen Tilting Wall-mount Unit

Model

CMPAK345

Installation Instructions

Thank you for purchasing the Hitachi Plasma Screen Wall-mount Unit.

To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this

manual in a safe place for future reference.

This plasma screen wall-mount unit is for use only with the following models:

HITACHI Plasma Screens: CMP307XE, CMP4121, CMP42PMA400E, CMP4202E, CL42PD2100,

42PD3000 & CMP5000WXE.

SUPPORTING VISION LTD

Manufactured in the UK TEL: 0845 6023109 FAX: 01283 792300

E-mail: info@supporting-vision.com

MOUNTING INSTRUCTIONS

CONSULT AUTHORIZED SERVICE PERSONNEL FOR THE INSTALLATION OF THIS UNIT.

INSTRUCTIONS MUST BE FOLLOWED PRECISELY FOR SAFE AND STABLE INSTALLATION.

SUPPORTING VISION LTD ARE NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED BY

MISHANDLING OR IMPROPER INSTALLATION.

Features

• Suspension system allows quick and easy

installation.

• Flat Installation – 22mm distance, wall to rear of

Plasma display

• Tilt – 0 to 10 degrees.

• Width adjustment – 30mm side to side screen

movement.

• Cable access – Pull bottom of screen away from

wall for Plasma connection access.

• Security bolt – Prevents removal of screen after

installation.

INSTALLATION

Installation of this unit should be carried out by

qualified technicians. Install in an appropriate

location only after checking wall structure and

durability for accident prevention. Consult a

qualified builder if in any doubt of wall structural

integrity

Wall Bracket for HITACHI Plasma Screen Models: CMP307XE, CMP4121,

CMP42PMS400E, CMP4202E, CL42PD2100, 42PD3000, CMP5000WXE.

List of Components

1. MOUTING WALL PLATE

Mount the wall plate on the wall using screws and/or bolts appropriate to wall construction (if in

doubt consult a qualified builder). Locate screws and/or bolts through all 8 holes (Fig. 1).

2. ATTACHING SUSPENSION PLATE TO PLASMA DISPLAY

Attach the suspension plate (Fig. 2) to rear of the Plasma screen using screws/washers/isolators

appropriate to model of the Plasma screen.

Refer to Fig. 2A for location holes relating to make and model of the Plasma Screen. Tighten screws

with hex head key supplied.

3. SCREEN ANGLE ADJUST - FLAT OR TILT?

Determine the amount of screen tilt required (0 to 10 degrees)

Adjust accordingly, loosening the angle adjustment socket screw (Fig. 1) to secure tilt plate

(Fig. 1) in preferred position.

For a flat 0 degree installation, lock the tilt plate into position by fastening cheese-head screws to

their maximum through locator holes on tilt plate.

Tighten angle adjustment screws - both sides (Fig. 1).

4. ENGAGING PLASMA/SUSPENSION PLATE WITH WALL BRACKET

Minimum two fit persons required

Lift the Plasma display to engage (Fig. 3) the two suspension hooks (Fig. 2) over suspension bar

(Fig. 1). The suspension bar is highlighted on the wall bracket by an orange sticker.

The screen is now suspended.

5. WIDTH ADJUSTMENT

The screen and the suspension plate can now be moved within a range of 3cm side-to-side on the

suspension bar (Fig. 4). This is to allow a flush-fitting location of multiple screens side-to-side or for

Plasma-wall installations.

6. CABLE CONNECTION

The Plasma display cable connections can now be accessed by pulling the bottom edge of the

display with the suspension plate away from the wall, as shown in Fig. 5.

7. SECURITY

Finally, using a screwdriver, fasten the silver M6/60 security bolt now accessed at the centre bottom

of the screen/suspension plate. When tightened, this will locate behind wall plate strap

(Figs. 1 and 5).

SCREEN REMOVAL

To remove the screen reverse step 7 by unfastening the security bolt. With a minimum two persons,

pull the display away from the wall at the bottom edge of screen and lift the display off its suspension

hooks.

Supporting Vision Ltd. Registered Office: 97 Lichfield Street, Tamworth, Staffs B97 7QF

FIG 1

WALL PLATE

Angle adjustment

Socket Screw

M5 Cheese-

head Screws

Tilt Plate

Suspension Bar

(Orange Sticker)

Wall Plate

Strap

FIG 2A

Hole Screen

Hitachi 37/42

Hitachi 50

Fixing

4 off, M6 x 20mm + washers

4 off, M8 x 20mm + washers

Nylon Insulating

Washer x4

Security

Bolt

Suspension Hooks

Steel

Washer x4

3 cm

movement

side to side

Angle

adjustment

screw

FIG 4 FIG 5

Fastening

bolt

Suspension Plate

Nylon Insulating Spacer Plug x4

(Panasonic & Toshiba screens)

FIG 3

Hook onto

bar on

wallplate

3 cm

Angle

adjustment

screw

11~20 cm

Wall

Access cable by

pulling display

away from wall at

base of screen

Fine adjust angle

using Angle

adjustment screw.

Secure screen

using fastening

bolt on backplate

FIG 2

Hitachi, Ltd. Tokyo Japan

Digital Media Division

292 Yohida-cho, Totsuka-ku, Yokohama,

244-0817 Japan

(045) 866-6302

Hitachi CMPAK345 Installation Instructions Manual

Hitachi CMPAK345 Installation Instructions Manual

Hitachi CMPAK345 Installation Instructions Manual

Related papers

Other documents