LIGHTING CONTROLS
STOP & START
Engine going into STOP mode Engine going into START mode
- with a manual gearbox ; at speeds below 12 mph (20 km/h),
when you put the gear lever into neutral, and you release the clutch
pedal,
- with the 6-speed electronic gearbox system; at speeds
below 5 mph (8 km/h), when you press the brake pedal or you
put the gear lever into position N.
- with a manual gearbox; when you depress the clutch pedal,
- with the 6-speed electronic gearbox system;
- gear lever in position A or M, when you release the brake
pedal,
- or gear lever in position N and the brake pedal released,
when you put the lever into position A to M,
- or when you engage reverse.
The "ECO" warning lamp goes off and the engine
restarts:
The "ECO" warning lamp comes on in the instrument
panel and the engine is put into standby:
1. Limiter mode On/Off.
2. Decrease the programmed value.
3. Increase the programmed value.
4. Speed limiter On/Off.
5. Display the list of memorised speeds.
1. Cruise control mode On/Off.
2. Programme a speed/Decrease the programmed value.
3. Programme a speed/Increase the programmed value.
4. Cruise control Off/Resume.
5. Display the list of memorised speeds.
CRUISE CONTROL
SPEED LIMITER
6-SPEED MANUAL GEARBOX
Engaging reverse gear
) Raise the ring under the knob and push the gear lever to the
left then forwards.
GEAR SHIFT INDICATOR
System which reduces fuel consumption by advising the driver to
change up on vehicles tted with a manual gearbox.
6-SPEED ELECTRONIC GEARBOX SYSTEM
R. Reverse
N. Neutral.
A. Automatic mode.
M. Manual mode with sequential gear changing.
AUTOMATIC GEARBOX
P. Park.
R. Reverse.
N. Neutral.
D. Automatic operation.
M+/-. Manual operation with sequential changing of the six gears.
) Select position N .
) Press the brake pedal down fully.
) Start the engine.
) Select rst gear (position M or A ) or reverse (position R ).
) Release the parking brake unless it is programmed to automatic
mode.
) Take your foot off the brake pedal, then accelerate.
Moving off
) With your foot on the brake, select position P or N .
) Start the engine.
) With the engine running, press the brake pedal.
) Release the parking brake, unless it is programmed to
automatic mode.
) Select position R , D or M.
) Gradually release the brake pedal.
A. Main lighting mode selection ring: turn it to position the symbol
required facing the mark.
Lamps off.
Automatic illumination of headlamps.
B. Stalk for switching headlamps: pull to switch the lighting between
dipped headlamps/main beam headlamps.
Sidelamps only.
Dipped headlamps or main beam headlamps.
C. Foglamp selection ring.
rear foglamps
front and rear foglamps
Windscreen wiper
A. Wiping speed control stalk: raise or lower the stalk to the
desired position
Fast wiping (heavy rain).
Normal wiping (moderate rain).
Intermittent wiping (proportional to the speed of the
vehicle).
Park,
Single wipe (press down or pull towards you, then
release).
Automatic wiping (press down, then release).
Single wipe (brie y pull the control stalk
towards you).
o r
WIPER CONTROLS
B. Rear wiper selection ring: turn the ring to place the desired
symbol against the marking.
REAR WIPER
Park,
Intermittent wipe,
Wash-wipe.
Turn the ring to its stop/the rear screen wash, then the
rear wiper operate for a set duration
Fiche_loueur_B71_C4_01-2010_an.i2 2Fiche_loueur_B71_C4_01-2010_an.i2 2 14/09/2010 13:19:3514/09/2010 13:19:35