Pleasant Hearth 18-600-310 Homeowner's Installation And Operating Instructions Manual

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 877-447-4768 8:30 a.m. – 4:30 pm CST, Monday – Friday.

or email us at [email protected]

HOMEOWNER’S INSTALLATION AND OPERATING INSTRUCTIONS

20-10-089 Rev.0/10

For installation with

Pleasant Hearth

Fireplace Mantel

W a r m i n g Y o u r H o m e. W a r m i n g Y o u r H e a r t.

C US

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING!

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY,

AN ELECTRICAL SHOCK OR FIRE MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

IMPORTANT INSTRUCTIONS

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE

PLEASANT HEARTH ELECTRIC FIREPLACE INSERT

FR-PLEASANT HEARTH ELECTRIC FIREPLACE INSERT (page 19)

SP-PLEASANT HEARTH ELECTRIC FIREPLACE INSERT (page 37)

MODEL/MODELE/MODELO #18-600-310 / GCE-1803 / GCE18TRG13 /

23-600-320 / GCE-2303 / GCE23TRG13

8280 Austin Avenue

Morton G r ov e, I L .

6 0 0 5 3 - 3 2 0 7

Tel: ( 847 ) 324 - 5900

Fax: ( 847 ) 324 - 5901

Toll Free (877) GHP Group

( 8 7 7 ) 4 4 7 - 4 7 6 8

www.ghpgroupinc.com

GHP

Safety Information ...................................................................................................3

Electrical Connection........................................................................................4

Grounding Instructions .................................................................................... 4

Remote Control................................................................................................ 5

Installation Instructions............................................................................................6

Fireplace Dimensions ........................................................................................ 6

Locating Your Fireplace ....................................................................................7

Fireplace Clearances ....................................................................................... 7

Installation.................................................................................................. 7 – 8

Operating Instructions.............................................................................................. 9

Fireplace Control Functions.............................................................................. 9

Control Panel.....................................................................................................9

Remote Control............................................................................................... 10

Care and Maintenance............................................................................................ 11

Glass Information............................................................................................11

Maintenance of Motors...................................................................................11

Cleaning................................................................................................11

Replacing the Light Bulbs ..................................................................... 12 - 13

Electrical Wiring Diagram .............................................................................. 14

Troubleshooting...................................................................................................... 15

Warranty..................................................................................................................................... 16

Replacement Parts List.................................................................................... 17 - 18

en Français .............................................................................................................. 19

en Español ...............................................................................................................37

Thank you and congratulations on your purchase of a GHP Group electric replace.

IMPORTANT: Read all instructions and warnings carefully before starting Installation.

Failure to follow these instructions may result in a possible electric shock,

injury to persons, re hazard and will void the warranty.

Please read the Installation & Operating Instructions

before using this appliance.

Electric Fireplace Insert 18/23

           2

Table of Contents

Electric Fireplace Insert 18/23

3          

SAVE THESE INSTRUCTIONS

1. Read all instructions before using this appliance.

2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this appliance. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes and curtains at least 3 feet (914mm) from the front of this appliance.

3. CAUTION: Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating unattended.

4. If possible always unplug this appliance when not in use.

5. Do not operate any heater with a damaged cord or plug or after the appliance

malfunctions, has been dropped or damaged in any manner.

6. Any repairs to this appliance should be carried out by a qualied service person.

7. Under no circumstances should this appliance be modied. Parts having to be removed

for servicing must be replaced prior to operating this appliance again.

8. Do not use outdoors.

9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.

Never locate this appliance where it may fall into a bathtub or other water container.

10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like.

Arrange cord away from trafc areas and where it will not be tripped over.

11. To disconnect this appliance, turn controls to the off position, then remove plug from outlet.

12. Connect to properly grounded outlets only.

13. This appliance, when installed must be electrically grounded in accordance with local codes,

with the current CSA C22.1 Canadian Electrical codes or for USA installations,

follow local codes and the National Electric Code, ANSI/NFPA No. 70.

14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this

may cause an electric shock, re or damage the appliance.

15. To prevent possible re, do not block air intakes or exhaust in any manner.

Do not use on soft surfaces, like a bed, where openings may become blocked.

16. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline,

paint or ammable liquids are used or stored. This appliance should not be used as a

drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it.

17. Use this appliance only as described in this manual. Any other use not recommended by the

manufacturer may cause re, electric shock or injury to persons.

18. Avoid the use of an extension cord because of the risk of overheating the cord and the risk of re.

Extension cords are for temporary use only. If an extension cord must be used,

it must be UL/CSA certied, rated at least for 15A (1875W), 125V with 14 AWG minimum and

constructed of two current carrying conductors with ground. A heavy duty extension

cord with the shortest length possible for the connection is recommended and must not be

longer than 50 ft. (15.2m). Do not coil or cover the extension cord.

Safety Information - IMPORTANT INSTRUCTIONS

A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the replace will

be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip

or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long three

wire cord, exiting the right side of the replace. Plan the installation to avoid the use of an extension cord.

Extension cords are for temporary use only. If an extension cord must be used, it must be UL/CSA certied,

rated at 15A (1875W), 125V maximum with 14 AWG minimum and constructed of two current carrying conductors

with ground. A heavy duty extension cord with the shortest length possible for the connection is recommended

and must not be longer than 50 ft. (15.2 m). Do not coil or cover the extension cord.

Electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of re, electrical shock

and injury to persons.

Do not use this replace if any part of it has been under water.

Immediately call a qualied service technician to inspect the replace

and replace any part of the electrical system which has been under water.

           4

This heater is for use on 120 volts. The cord has a plug as shown at (A) in Figure 1. An adapter as shown at (C)

is available in the USA only for connecting three-blade grounding-type plugs to two-slot receptacles. The green

grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet

box. The adapter should not be used if a three-slot grounded receptacle is available. NOTE: Adapters are NOT for

use in Canada.

Electrical Connection

Grounding Instructions

Electric Fireplace Insert 18/23

GROUNDING

PIN

METAL SCREW

GROUNDING

MEANS



COVER OF GROUNDED

OUTLET BOX

ADAPTER

(A)

(B)

(C)

(D)

Figure 1

GROUNDING

5          

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules and Industry Canada ICES-003.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

might cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

DO NOT mix old and new batteries.

DO NOT use rechargeable Cadmium-sliver oxide cell batteries with remote control unit.

DO NOT mix Alkaline, Standard (Carbon-Zinc), or Rechargeable (Nickel-Cadmium) batteries.

DO NOT dispose of batteries in re. Improper disposal may cause batteries to leak or explode.

Remote Control

The remote control requires 1 Lithium Coin Cell Battery (size-CR2025) which is included.

Electric Fireplace Insert 18/23

           6

Installation Instructions - Fireplace Dimensions

Electric Fireplace Insert 18/23

Ref.

A 19-3/16" (487.5mm) 24-15/16" (617.5mm)

B 18-7/16" (469mm) 20-15/64" (514mm)

C 17-47/64" (450.5mm) 22-53/64" (580mm)

D 17-23/32" (450mm) 19-31/64" (495mm)

E 8-1/32" (204mm) 8-1/32" (204mm)

F 7-61/64" (202mm) 7-61/64" (202mm)

G 16-1/16" (408mm) 21-3/16" (538mm)

H 13-15/32" (342.5mm) 15-1/4" (387.5mm)

VOLTAGE 120 V AC

FREQUENCY 60Hz

HEATER RATING 1350W

MAX AMPS - 18" 12A

MAX AMPS - 23" 12.5A

Technical Specifications

18-600-310 / GCE-1803 / GCE18TRG13 23-600-320 / GCE-2303 / GCE23TRG13

7           

1. Locate your assembled Pleasant Hearth wood mantel near a 15 amp / 120 volt grounded

electric outlet. Read all instructions before using this appliance.

2. Place the insert directly in front of the mantel opening.

3. Carefully lift the insert through the center opening in the front of the replace. The bottom

of the insert has two foam rubber strips to prevent scratching of the hearth base. Slide the

insert back through the opening until the metal trim makes contact with the front of the mantel.

4. Install the mounting brackets provided with the insert in the pre-drilled holes on the top

of the insert (see Figure 2).

5. Carefully position mantel with installed replace against wall.

6. Plug the power cord into the 15 amp / 120 volt outlet. Use an extension cord rated for a

minimum of 1875 watts if necessary.

• Out of direct sunlight

• Not susceptible to moisture

• Away from uninsulated outside wall

• At least 3 feet (.9m) from drapery, furniture and other combustibles

The Fireplace should be located in an area:

NOTE: Make sure that the unit is installed so that the power cord

is not compressed against or caught on the unit or the mantel and

that it has an unobstructed path to the grounded outlet.

Locating Your Fireplace

Fireplace Clearances

Installation

Electric Fireplace Insert 18/23

Sides......................2

27

/

64

” (61.5 mm)

Floor.......................0” (0 mm)

Top.........................2” (51 mm)

Front......................36” (914 mm)

Rear.......................

25

/

32

” (20 mm)

Clearance to Combustibles

Wooden Facing (up to 5/8” (16 mm) thick): 5/16” (8mm)

          8

Open the unit and check carefully for visible damage.

If you have any problems with installation, operation, missing parts, or damage,

please call 877-447-4768 for service.

Figure 2

Mounting Brackets

DO NOT dispose of packaging until you are satised with your replace.

DO NOT return unit to store before calling toll free 877-447-4768 for service.

Installation

Electric Fireplace Insert 18/23

2

3

1

9            

Electric Fireplace Insert 18/23

The replace features conveniently separate controls for ame effect and for heater control.

This allows you to operate the unit in two (2) different modes:

• As a full-featured replace - both ame effect and heater are on.This mode

allows you to enjoy the look of the re along with the heat output of a heater.

• As a visual effect - only the ame effect is on, the heater is off. We recommend this mode for

warm weather application, when you want the ambiance of a re, without any heat output.

The replace control functions can be accessed in two (2) ways:

• Using the touchpad control panel, located in the upper right-hand corner of the replace

behind the hinged control access door.

• Using the multifunction remote control unit.

Main Power Button:

This button supplies power to all the functions of the replace. The Main power button must be

in the ON position, either from the remote or on the touch pad for the functions to work.

Heater Control Button:

This button controls the heater ON/OFF and 5 temperature modes from High to Low. When the

replace is rst turned on, the heater will come on at the highest room temperature setting.

Each time the Temperature button is pressed, the temperature set point decreases, allowing you

to adjust the ambient temperature.

Flame Control button:

This button controls the brightness of the ame effect with settings at High, Medium and Low.

When the replace is rst turned on, the ame will come on at the highest setting. Each time the

Flame button is pressed, the ame brightness decreases. The only way to turn off the ame effect

completely is to turn off the Main Power button.

1.

2.

3.

Operating Instructions - Fireplace Control Functions

Control Panel

Figure 3 / Control Panel

         10

Electric Fireplace Insert 18/23

Figure 4

Remote Control

The infrared remote control relies on a line of sight and must be pointed at the ame/screen of the

replace to work. The remote control unit has the controls required to turn ON/OFF both the main

power and the heater. If you prefer to use the touchpad control on the replace unit itself, open the

hinged door on the upper right hand side of the replace to access the touchpad buttons. The layout

of the buttons on the touchpad and remote control unit can be seen in Figures 3 & 4, respectively.

1. Plug your replace into a 15 amp

120 volt power outlet.

2. Turn the power on (see illustration for Main Power

Button location). Flame will show on the back

screen of the replace.

3. Remove plastic tab from inside battery compartment

to activate remote control. (see Figure 5)

4. Point the remote control directly at the replace

ame/screen and use the buttons to operate

the replace.

Main Power Button:

This button supplies power to all the functions of the replace. The Main power button must be

in the ON position, either from the remote or on the touch pad for the functions to work.

NOTE: Be sure the unit is unplugged before installing, moving or performing maintenance.

Heater Control Button:

This button controls the heater ON/OFF and 5 temperature modes from High to Low. When the

replace is rst turned on, the heater will come on at the highest room temperature setting.

Each time the Temperature button is pressed, the temperature set point decreases, allowing you

to adjust the ambient temperature.

Flame Control Button:

This button controls the brightness of the ame effect with settings at High, Medium and Low.

When the replace is rst turned on, the ame will come on at the highest setting. Each time the

Flame button is pressed, the ame brightness decreases. The only way to turn off the ame effect

completely is to turn off the Main Power button.

1.

2.

Operating Instructions - Fireplace Control Functions

Remote Control

The plastic tab inside the battery

compartment MUST

be removed before remote control

will operate. (pull tab)

Figure 5 / Battery

3.

2

3

1

1. Under no circumstances should this product be operated with broken glass.

2. Do not strike or slam the glass.

3. Do not use abrasive cleaners to clean the glass.

4. This product uses tempered glass. Replacement of the glass supplied by the

manufacturer should be done by a qualied service person.

Always disconnect the appliance from the main power supply

and allow it to cool before any servicing operation.

The motors used on the fan heater and ame blower are pre-lubricated for extended bearing life

and require no further lubrication. However, periodic cleaning/vacuuming of the appliance around

the air intake and exhaust, as well as the fan heater is recommended. For heavy or continuous use,

periodic cleaning must be done more frequently. If the heater blows alternating cold and warm air,

check the fan for free movement and for debris restricting air ow. If the fan does not move freely, the

unit must be turned off and the fan replaced immediately in order to prevent further damage to the unit.

Before attempting ANY maintenance:

1. Turn off power to the unit.

2. Unplug the power cord from outlet.

3. Let replace cool if it has been operating.

11          

Care and Maintenance

Glass Information

Maintenance of Motors

Cleaning

Cleaning of the control panel, located in the upper right-hand corner of the replace behind the hinged

control access door, is to be done only using a soft cloth, slightly dampened in water (if needed, a small

amount of dish soap can be added to the water) and dried using a clean, dry soft cloth. Cleaning of the

screen diffuser is to be done using only water and a lint free cloth. DO NOT use any abrasive household

cleaners as these products will damage the touchpad controls and the diffusing screen.

Electric Fireplace Insert 18/23

           12

The 18” models use two (2) 40 watt, E-12 socket base light bulbs. The 23” models use two (2) 60 watt, E-12

socket base light bulbs. These are small base bulbs typically found in chadeliers with candle shaped bulbs.

The bulbs are located underneath the logset/ emberbed. For convenience, if one of the bulbs burns out, it may

be easier to replace both of the bulbs at the same time.

Replacing the Light Bulbs

Before attempting ANY maintenance:

1. Turn off power to the unit.

2. Unplug the power cord from outlet.

3. Let replace cool if it has been operating.

Electric Fireplace Insert 18/23

WARNING: Do not replace bulbs with higher wattage bulbs. Use of higher

rated bulbs may result in a re, causing property damage, personal injury,

or loss of life.

1. Turn off power to the unit and

ensure that it is unplugged

from the electrical outlet.

2. Let the replace cool if it has

been operating.

Thumb Screws

3. Remove the glass front from

the unit by unscrewing the

two thumbscrews counter-

clockwise at the top of

the glass door.

See Figure 5.

Figure 5

4. Locate the two log set bolts

on the left and right side of

the top of the ember bed and

remove them by unscrewing

them counterclockwise .

See Figure 6.

Figure 6

Log Bolts

13          

Replacing the Light Bulbs

Electric Fireplace Insert 18/23

5. Remove log/ember bed

by grasping and lifting

up gently.

6. Visually locate the light

bulbs and remove them

by unscrewing them

counterclockwise .

See Figure 7.

7. Install new light bulbs by

screwing the bulbs into the

sockets clockwise .

See Figure 8.

8. Reinstall the log/ember bed

and secure using the two log

bolts previously removed.

See Figure 8.

Figure 7

9. Reinstall the glass front

and secure using the two

thumbscrews.

10. Restore power to the

unit and ensure that it

is operating properly.

Figure 8

           14

Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician

in accordance with national and local codes.

If repairing or replacing any electrical component or wiring, the original

wire routing, color coding and securing locations must be followed.

Any electrical re-wiring of this appliance must be done by a qualied

electrician. This wiring must be done in accordance with local codes

and/or in Canada with the current CSA C22.1 Canadian Electrical Code,

and for US installations, the National Electrical Code ANSI/NFPA NO 70.

Electrical Wiring Diagram

WARNING: Disconnect Power Before Servicing

Electric Fireplace Insert 18/23

CIRCUIT DIAGRAM

4 Black

2 Black

1 Black

3 Black

8 White

11 White

10 White

9 White

7 White

5 Black

12 Black

Power I/O

Heater Circular

Control

Flame Circular

Control

Temperature

sensor

6 Black

Thermal

Cutout

of fuse

Fan Heater

Lamp

CIRCUIT

BOARD

Heater element

FUSE

Heating indicator

H L

Flame indicator

H/M/L

15           

Troubleshooting

Corrective Action

Fireplace does not operate; 1. The fireplace is not plugged in. 1. Make sure the fireplace is plugged in to a

the ON/OFF power light on the standard 120V outlet.

control panel is not lit.

2. A circuit breaker is tripped or a fuse blown. 2. Check additional appliances on the circuit;

ideally the fireplace should be on a dedicated

15 amp circuit.

3. Defective ON/OFF switch. 3. Call customer service at (877) 447-4768.

4. Loose wiring. 4. Call customer service at (877) 447-4768.

Power light is ON but the back 1. Incorrect operation. 1. Refer to operating instructions.

flame is not bright/visible.

2. Light bulbs burnt out. 2. Replace light bulbs.

3. Loose wiring. 3. Call customer service at (877) 447-4768.

Excessive noise when the flame is 1. Rotating flame reflector shaft rubbing 1. Open back of firebox and reposition flame

ON but the heater OFF. against housing. reflector shaft. Turn off unit prior to servicing.

2. Defective flame reflector shaft motor. 2. Call customer service at (877) 447-4768.

Heater is not operating. 1. Incorrect operation. 1. Refer to operating instructions.

2. Defective heater switch. 2. Call customer service at (877) 447-4768.

3. Defective heater assembly. 3. Call customer service at (877) 447-4768.

4. Loose wiring. 4. Call customer service at (877) 447-4768.

5. Dirty or clogged louver door. 5. Unplug the unit. Clear louver area of dust

and debris. Wait five minutes, plug the unit in

again and turn on the heater.

Excessive noise when the heater 1. Dirty or clogged blower. 1. Refer to Maintenance of Motors section of

is operating. Instruction Manual.

2. Defective heater assembly. 2. Call customer service at (877) 447-4768.

Back flame light on 1. Defective flame effect motor. 1. Call customer service at (877) 447-4768.

but flames not moving.

2. Flame reflector not secured to motor. 2. Open unit and tighten flame reflector to motor.

Problem Possible Cause

Electric Fireplace Insert 18/23

           16

BASICWARRANTY:

GHP Group (hereinafter referred to collectively

as the “Company”) warrants that your new

electric replace is free from manufacturing and

material defects for a period of one year from

date of purchase, subject to the following

conditions and limitations.

1. This electric replace must be installed and

operated at all times in accordance with

the Installation and Operating instructions

furnished with the product. Any alteration,

willful abuse, accident, or misuse of the

product shall nullify this warranty.

2. This warranty is non-transferrable, and is

made to the original owner, provided that the

purchase was made through an authorized

supplier of the Company.

3. This warranty is limited to the repair or

replacement of part(s) found to be defective

in material or workmanship, provided that

such part(s) have been subjected to normal

conditions of use and service, after said defect

isconrmed by the Company’s inspection.

4. The Company may, at its discretion, fully

discharge all obligations with respect to this

warranty by refunding the wholesale price of

the defective part(s).

5. Any installation, labor, construction,

transportation, or other related costs/

expenses arising from defective part(s), repair,

replacement, or otherwise of same, will not

be covered by this warranty, nor shall the

Company assume responsibility for same.

Further, the Company will not be responsible

for any incidental, indirect, or consequential

damages, except as provided by law.

1 YEAR WARRANTY

For GHP Group Electric Fireplace

6. All other warranties - expressed or implied-

with respect to the product, its components

and accessories, or any obligations/liabilities

on the part of the Company are hereby

expressly excluded.

7. The Company neither assumes, nor

authorizes any third party to assume, on its

behalf, any other liabilities with respect to the

sale of this product.

8. The warranties as outlined within this

document do not apply to non-GHP Group

accessories used in conjunction with the

installation of this product.

This warranty is void if:

a) The replace has been operated in

atmospheres contaminated by chlorine,

uorine or other damaging chemicals.

b) The replace is subjected to prolonged

periods of dampness or condensation.

c) Any alteration, willful abuse, accident, or

misuse of the product.

IF WARRANTY SERVICE IS NEEDED . . .

1) Contact GHP Group customer service.

Make sure you have your warranty, your

sales receipt, and the model/serial number

of your GHP Group product.

2) DO NOT ATTEMPT TO DO ANY

SERVICE WORK YOURSELF.

Electric Fireplace Insert 18/23

8280 Austin Avenue

Mo r ton G r ove, I L.

6 0 0 5 3 - 3 2 0 7

Tel: ( 847 ) 324 - 5900

Fax: ( 847 ) 324 - 5901

Toll Free (877) GHP Group

( 8 7 7 ) 4 4 7 - 4 7 6 8

www.ghpgroupinc.com

GHP

17        20-10-089Printed in China

Replacement Parts List

Electric Fireplace Insert 18/23

Ref. Description

18-600-310

GCE-1803

GCE18TRG13

23-600-320

GCE-2303

GCE23TRG13

1 Top panel

EF18023350X EF23022350X

2 Left side panel

EF18023351X EF23022351X

3 Right side panel

EF18023352X EF23022352X

4 Back panel

EF18023354X EF23022355X

5 Glass door frame

EF18023104X EF23022105X

6 Flame panel assembly

EF18023103X EF23022103X

7 Mounting bracket kit

EF33405A EF33405A

8 Fan-Heater

EF23022501X EF23022501X

9 Screen

EF18023366X EF23022389X

10 Flame reflector

EF18376A EF23373AS

11 Bulb base

EF23022505X EF23022505X

12 Bulb

EF18023505X EF23022504X

13 Logset

EF18023365X EF23022387X

14 Logset bolt

EF23022388X EF23022388X

15 Control panel label

EF18512AS EF18512AS

16 Control panel

EF33504AS EF33504AS

17 Remote control

EF33510AS EF33510AS

18 Power cord & connector

EF33511A EF33511A

19 Flame effect motor

EF23022506X EF23022506X

20 Main circuit board

EF23022502X EF23022502X

21 Glass panels

EF18023365X EF23022515X

22 Bottom panel

EF18023101X EF23022101X

23 Control access door

EF23022104X EF23022104X

24 Thumbscrew for glass door

EF23022394X EF23022394X

For replacement parts, call our customer service department

at 877-447-4768 8:30 a.m. – 4:30 p.m. CST, Monday – Friday.

           18

Replacement Parts

Electric Fireplace Insert 18/23

Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant,

appelez notre service à la clientèle au 877 447 4768, entre 8 h 30 et 16 h 30, HNC, du lundi au

vendredi, ou envoyez-nous un courriel à l’adresse suivante : [email protected].

DIRECTIVES D’INSTALLATION ET D’UTILISATION

À installer avec le

manteau pour foyer

Pleasant Hearth.

C US

REMARQUE À L’INTENTION DE L’INSTALLATEUR : Veuillez laisser ce manuel au propriétaire.

REMARQUE À L’INTENTION DU CLIENT : Veuillez conserver ce manuel pour vous

y référer ultérieurement.

AVERTISSEMENT!

RESPECTEZ SCRUPULEUSEMENT LES DIRECTIVES DU PRÉSENT MANUEL

POUR PRÉVENIR LES CHOCS ÉLECTRIQUES, LES INCENDIES, LES

DOMMAGES AINSI QUE LES BLESSURES GRAVES OU MORTELLES.

CONSIGNES IMPORTANTES

VEUILLEZ LIRE CE MANUEL AVANT D’INSTALLER OU D’UTILISER LE FOYER.

FOYER ÉLECTRIQUE ENCASTRABLE PLEASANT HEARTH

MODÈLE Nº 18-600-310 / GCE-1803 / GCE18TRG13 /

23-600-320 / GCE-2303 / GCE23TRG13

FRANCÁIS

20-10-089                                                                              Rév. 0/10

Réchauffez votre résidence. Réchauffez votre cœur.

8280 Austin Avenue

Morton G r ov e, I L .

6 0 0 5 3 - 3 2 0 7

Tel: ( 847 ) 324 - 5900

Fax: ( 847 ) 324 - 5901

Toll Free (877) GHP Group

( 8 7 7 ) 4 4 7 - 4 7 6 8

www.ghpgroupinc.com

GHP

Merci et félicitations pour votre achat d’un foyer électrique de GHP Group.

IMPORTANT : Lisez attentivement toutes les directives et les avertissements avant

de procéder à l’installation. Le non-respect de ces directives peut provoquer un choc

électrique, des blessures et un incendie, et annule la garantie.

Veuillez lire les directives d’installation et

d’utilisation avant d’utiliser ce foyer.

           20

Consignes de sécurité ........................................................................................... 21

Branchement électrique..................................................................................22

Directives de mise à la terre ............................................................................22

Télécommande ............................................................................................... 23

Directives d’installation..........................................................................................24

Dimensions du foyer .......................................................................................24

Choix de l’emplacement du foyer .................................................................... 25

Dégagement du foyer ..................................................................................... 25

Installation................................................................................................. 25-26

Directives d’utilisation .............................................................................................27

Fonctions de commande du foyer...................................................................27

Tableau de commande....................................................................................27

Télécommande............................................................................................... 28

Entretien................................................................................................................... 29

Renseignements sur la vitre............................................................................29

Entretien des moteurs.....................................................................................29

Nettoyage................................................................................................29

Remplacement des ampoules................................................................... 30-31

Schéma de câblage........................................................................................32

Dépannage............................................................................................................... 33

Garantie..................................................................................................................................... 34

Liste des pièces de rechange..........................................................................35-36

en Español ............................................................................................................... 37

Table des matières

Foyer électrique encastrable 18/23

Page is loading ...

Pleasant Hearth 18-600-310 Homeowner's Installation And Operating Instructions Manual

This manual is also suitable for

Pleasant Hearth 18-600-310 Homeowner's Installation And Operating Instructions Manual

in other languages

Related papers

Other documents