McALPINE BK2 Centre PIN 60mm Basin Waste and 1 1/4 Inch P TRAP User manual
- Type
- User manual
L-BK2 December 2020
McALPINE
L-BK2 December 2020
McALPINE
BK2
CENTRE PIN 60mm BASIN WASTE
AND 1 1/4” P-TRAP ASSEMBLY
Installation and maintenance instructions
Components
Waste & Plug assembly P-Trap assembly
Minimum Basin Thickness = 23mm
Maximum Basin Thickness = 45mm
Without Using Spacer
Minimum Basin Thickness = 0 mm
Maximum Basin Thickness = 23mm
When Using Spacer
INSTALLATION WITH SPACER ON A
WASH-HAND BASIN (WHB) WITHOUT OVERFLOW
INSTALLATION ON A WASH-HAND BASIN (WHB)
WITH OVERFLOW.
1.
Place the Waste (3) with the white Washer (4) or apply
sealant into the waste hole in the WHB.
2. Drop the Ferrule (2) through the centre of the Waste (3).
3. Assemble the black washer (7) to the flange on the stalk (8),
add the spacer (6) and then the silicon Washer (5).
4.
Position items 5,6,7,8 on the underside of the WHB at the waste
outlet hole, and tighten (**No more than hand tight + 1/4 turn) the
Ferrule (2) clockwise until the waste assembly is fixed to the
WHB.
5. Finally, assemble the spring loaded plug assembly (1) by
pushing the stem of the plug into the centre-pin ferrule (2).
6. Remove Inlet Nut (9) and Blue seal (10) from the trap body and
assemble onto the waste assembly outlet stalk (8).
7. Assemble the Trap Body (10) onto the outlet stalk (8) push the
seal (10) into the trap body then tighten the Inlet Nut (9)
**No more than hand tight + 1/4 turn.
8. Assemble the Outlet Nut (13), Backup Washer (12) and Outlet
seal (11) onto the outlet pipe and push into the outlet of the
Trap Body (10). Push the Outlet Seal (11) and Backup
Washer (12) forward into the trap body outlet, then tighten
outlet nut (13). **No more than hand tight + 1/4 turn.
1.
Place the Waste (3) with the white Washer (4) or apply
sealant into the waste hole in the WHB.
2. Drop the Ferrule (2) through the centre of the Waste (3).
3. Assemble the black washer (7) to the flange on the stalk (8)
4.
Position items 7 and 8 on the underside of the WHB at the waste
outlet hole, and tighten (**No more than hand tight + 1/4 turn) the
Ferrule (2) clockwise until the waste assembly is fixed to the
WHB.
5. Finally, assemble the spring loaded plug assembly (1) by
pushing the stem of the plug into the centre-pin ferrule (2).
9. Important - Run water through completed installation,
Inspect all joints for leaks.
Installation instructions for CWP60-SSP: Spring loaded centre pin basin waste (Sub-assembly)
FIXING INSTRUCTIONS: DRY FIX. NO SEALANT-REQUIRED.
Spacer + Washer
Installation instructions for P-Trap Complete Installation
Maintenance
Remove Plug Assembly (1) from waste, clean debris from waste.
Flush water through trap periodically to clear debris from the
trap body.
6
3
1
2
4
5
7
8
9
10
11 12 13
Spacer + Washer
11
Spacer and Washer for use
in basins with no overflow
If the basin profile is
uneven, McAlpine
recommend using new
Sealant in place
of Item (4)
SEAL
SEAL SEAL
75mm
WATER SEAL
124
60
129
1 1/4"
MULTIFIT
-
1
