1、充电盒需要长期贮存时，请将充电盒断电包装好，放置于干燥通风处，
每半年检查一次。
2、充电盒应贮存在清洁、干燥、通风处，应避免与腐蚀性物质接触，远离火源
及热源。
3、贮存温度:-5℃~+35°℃。贮存相对湿度:≤75%RH。
4、充电盒应包装成箱进行运输，在运输过程中应防止剧烈振动、冲击或挤压
防止日晒雨淋，可使用汽车、火车、船舶、飞机等交通工具进行运输。
1、产品的保修期为一年
不按照使用说明和使用注意事项操作，所导致的产品损坏将不在保修范围内。
2、保修期的确定
保修期确定:产品保修期自您购买本产品之日起计算，产品保修卡为有效保修
凭证。
3、保修限制条款
对于下列原因导致的产品故障，本公司不提供承诺中的标准服务：
非本公司产品及部件。
超过保修期。
使用非本公司提供的转接线与移动电源连接产生的故障。
不可抗拒因素，如:地震、火灾等自然灾害或意外事故等不可抗拒因素引起。
不能工作或部件损坏。
自行拆卸、修理或跌落造成的产品故障。
因为电压选择不对，导致用电器损坏。
人为使用不当，导致的电池损坏。
维修记录卡
本保修卡遗失后不再发行，请妥善保管
本产品在出厂前已经过了严格的检验。如遇问题，请与公司售后服务部或经销
商联系。严禁自行拆卸。
深圳市正光影像器材有限公司
深圳市龙华新区大浪下早工业区一栋5楼
网址:www.zgcine.com
日期 维修内容 备注
-20°C~+55℃
135mm*73mm*66mm
3.7V 3400mah
产品名称
电池容量
类别 充电盒
最大充电
满电时间
USB-C输入
USB-A输出
USB-C输出
尺寸
重量
材质
230g
约2小时
ABS
工作温度
适用设备
电量指示灯
开关按键
USB-A 输出
USB-C PD输入
加入了热敏电阻和温控处理
机制,确保锂电池在安全的温
度范围内工作。
温度保护
加入保险丝器件,在异常短路
时自动保护,防止主板和电池
的毁损。
短路保护
通过OVP电路的处理,防止输
入电压过高,以避免对后端电
路造成损坏。
过压保护
智能实施检测输出电流,当输
出电流超出上限时,主动关闭
输出,保护待充电设备。
输出过流保护
内设安全集成电路,拥有强大的多重保护功能强悍兼容原装及品牌电池
当产品充电时,出现异常会自
动中断工作,保护充电设备。
输出防反保护
智能适时检测输出电压,当输
出电压超出上限时,主动关闭
输出,保护待充电设备。
输出过压保护
加入锂电池保护器件,有效避
免电池的过充过放,防止损伤
电池。
电池过充保护
快速简易使用充电设备
即插即用
1：体积小巧，可轻松随身携带；
2：智能控制充电全程、抗电压等多中测试充电器电池内自带保护、防止过充、
过压、过温、过流、快速稳定、安全可靠；
3:精准卡位轻松安装,卡位更加精准取放充电产品轻松自如轻晃也不易掉落；
4:指示灯显示轻松查看电池容量,轻松掌握充电状态；
5:充电器设有三个充电槽,可随意充一到三个产品,快速充电,防止电池过充,为您
节省充电时间;
6:支持多个设备同时使用，支持边充边放功能,大容量，持久续航；
7:采用防火阻燃材料制造无惧户外复杂多变充电环境；
8: 可同时给 3个Rode Wireless GO 麦克风进行充电3次。
RODE罗德wireless go/wireless go II无线麦克风系列产品
25 50 75 100
充电盒x1 说明书x1 USB-C充电线x1 USB-A充电线x1 手提袋x1
-20°C~+55℃
135mm*73mm*66mm
3.7V 3400mah
Model
Battery
Capacity
Type Charging Case for
Rode Wireless Go Series
Fully
Recharge Time
USB-C Input
USB-A Output
USB-C Output
Dimension
Weight
Body Material
230g
About 2 hours
ABS
Operate
Temperature
Applicable
equipment
Battery Indicator light
Power Button
USB-A Output
USB-C PD Input
Built-in safety integrated circuit, with strong multiple protection
function, compatible with the original and brand batteries
1：Compact design makes it easy to carry around.
2：Intelligent control of the charging process, to prevent over-charge,
over-voltage, over-temperature, over-current, fast and stable, safe and reliable;
3:accurate slot makes the charging products are easy to install, and would
not fall off when shaking lightly.
4:You can observe the battery capacity through the indicator light, easy to
grasp the charging state;
5:Equipped with three charging slots, you can charge 1~3 products at will,
fast charging to save your time and prevent the battery over-charge.
6:Support the use of multiple devices at the same time, support charging
and discharging at the same time, large capacity, long-lasting battery life;
7:Fire retardant materials adapt to the complex outdoor charging environment.
Rode Wireless Go Series Microphone
25 50 75 100
charging case x1 user manual x1 Carrier bagx1
USB-C Cable x1 USB-A Cable x1
Ready to use immediately when you
connect it to the charging device.
Plug and Play
产品使用说明书
Rode wireless Go充电盒
产品简述 产品参数
产品特点
产品介绍
产品功能特点
产品操作说明
产品贮存及运输
维修及售后服务
包装清单
ZG-R30是用于RODE罗德wireless go专用充电盒，这款
充电盒采用磁吸开合盖设计;具有过流保护、过压保护、过
温保护以及异常检测功能，可防止设备电池过充损坏;充电
盒采用阻燃材料，确保设备安全充电。 TYPE-C*3 500ma(MAX) 5V 2.4A
5V 2.4A 9V 2A 12V 1.5A(MAX)
5V 2.4A 9V 2A 12V 1.5A(MAX)
ZG-R30
User Manual
ZG-R30
Description Product Technical Parameters
Feature
Introduction
Function
Operation Guide
Battery Status:Press the button to check the remaining battery. Each
white light blinks represents 25% percent of remaining battery.
Working Status:Solid white light always display when the device is working.
Standby Mode: If no operation within 30 seconds,the light will turn off
automatically .
Quick standby Mode:Double click the button,the light will be turn off .
ZG-R30 is a charging Case which is designed for
the RODE Wireless Go microphone, which has a
soft contours and neat exterior design with
over-current protection, over-voltage protection,
over-temperature protection and abnormal
detection functions, can prevent the battery
damage due to over-charge; Charging Case adopts
flame retardant material to ensure safe charging
of equipment.
TYPE-C*3 500ma(MAX) 5V 2.4A
ZG-R30
Packing list
1、If the charging case is not used for a long time, please charge it to half-full state,
place it in a dry and ventilated place, and check per six months.
2、Charging case should be stored in a clean, dry and ventilated environment, avoid
contact with corrosive substances, also be away from fire and heat sources.
3、Store temperature: -5℃~+35°℃ Relative humidity≤75%RH
4、The charging case should be packed into cartons for transportation.
During transportation, it should prevent violent vibration, impact or extrusion,
and prevent sun and rain. It can be transported by vehicles, trains, ships, planes
and other means of transportation
Storage and Transportation
电量显示：按下按键，电量指示灯亮白色。
待机显示：电量指示灯显示30秒内，无操作指示灯熄灭。
输出显示：电量指示灯常亮。
强制待机：连续按下2次按键，电量指示灯熄灭。
3、Warranty Limitation
For the following cases of product failure, the company will not provide
the warranty service as promised:
Products and components do not belong to our company.
Out of warranty.
Fault caused by the transfer wiring or mobile power which are not
provided by our company.
Force majeure factors, such as earthquake, fire and other natural
disasters or accidents.
Aging or damage of components.
Product failure caused by self-disassembly, repair or drop.
Damage caused by incorrect voltage selection.
Damage due to improper using.
Maintenance record card
This warranty card will not be reissued after loss, please keep it properly.
This product has passed strict inspection, In case of any problem, please
contact the company's after-sales service department or the dealer.
Prohibit self-disassembly.
Date Repaired parts Remark
1、One year warranty
2、Warranty period
Warranty period: the warranty period of the product is calculated from the
date you purchase the product. The warranty card is the valid warranty
certificate.
The damage due to failure to operate in accordance with the instructions
and precautions will not be covered by the warranty.
Shenzhen Zhengguang imaging Equipment Co.,Ltd.
Add：5th Floor,1st Building,Xiazao Industrial Park, Shenzhen, Guangdong, China
Web:www.zgcine.com
Email:[email protected]om
Maintenance and after-sales service
thermistor and temperature control
processing mechanism are added to
ensure the lithium battery works in a
safe temperature range.
Temperature protection
add fuse device, trigger automatic
protection in case of abnormal short
circuit, to avoid the damage of
motherboard and battery.
Short circuit protection
the OVP circuit design makes sure to
prevent the over high input voltage,
to avoid damage to the back end circuit.
Overvoltage protection
intelligent detection of output current,
when the output current exceeds the
limit, the output circuit would be shut
down automatically to protect the
charging device.
Output overcurrent protection
if the installation is wrong, it will
automatically interrupt the work to
protect the charging equipment.
Output anti-reverse protection
intelligent real-time detection of
output voltage, when the output
voltage exceeds the upper limit, it will
automatically close the output circuit
to protect the charging device.
Output overvoltage protection
add lithium battery protection device,
effectively avoid the battery overcharge and
over-discharge, prevent damage to the battery.
Battery overcharge protection
/
