Furuno GP-150 User manual

Furuno
Brand
Furuno
Model
GP-150
Category
Navigators
Type
User manual

Furuno GP-150 is a high-performance GPS navigator designed for marine use. It offers various display modes, including plotter, 3D, highway, navigation, and data, allowing you to customize your view based on your needs. You can zoom in and out, shift the cursor and display, and center your own ship's position. The GP-150 enables you to set and cancel destinations, create and register routes, and mark important locations using various shapes and line types. It also features an event mark for MOB (Man Overboard) situations and an arrival alarm to alert you when approaching your destination.

Furuno GP-150 is a high-performance GPS navigator designed for marine use. It offers various display modes, including plotter, 3D, highway, navigation, and data, allowing you to customize your view based on your needs. You can zoom in and out, shift the cursor and display, and center your own ship's position. The GP-150 enables you to set and cancel destinations, create and register routes, and mark important locations using various shapes and line types. It also features an event mark for MOB (Man Overboard) situations and an arrival alarm to alert you when approaching your destination.

GPS NAVIGATOR GP-150/DUAL
Operator’s Guide
The purpose of this Guide is to provide basic operating procedures for this equipment. For more
detailed information, see the Operator's Manual.
Selecting a Display Mode
Press DISPLAY SEL to select desired mode.
Plotter 1/Plotter 2
234°
D3D 100m
SAFE
34° 23.456´ N 135° 45.678´ E
BRG
345°
BRG To +
11.5
RNG To +
nm
123°
COG
001
30
40
20
50
H
16.00
This column does not
appear on Plotter 2 display.
Ship's track and
data
WGS84
Highway
34°
D3D 100m
SAFE
34° 23.456´ N 135° 45.678´ E
BRG
45°
RNG
12.3
SOG
kt
0.35
nm
COG
WGS84
3D view of ship's
track overlaid on
intended course
Navigation
E
3D
N
S
SOG
RNG
TRIP
nm
kt
VTD
kt
nm
BRG
23:45'
17H 45M
TO; 012
0.1nm 0.1nm
15
63°
123°
CSE
ETA TTG
D3D 100m
SAFE
Graphic display
of steering data
WGS84
12.3
10.3
123
789
Data
JUN 12, 2006 23:59'59" U
12° 23.456' N
123° 23.456' E
POSITION
RNG
31.23 nm
SOG
12.3 kt
BRG
223.4°
COG
123.4°
TO : 001
MARINE
POINT1
NEXT
: 002
MARINE
POINT2
D3D 100m
SAFE
Comprehensive
navigation data
display
Enlarging/Shrinking the
Display
Press ZOOM IN to enlarge.
Press ZOOM OUT to shrink.
Shifting the Cursor
1) Press CURSOR ON/OFF to turn on the
cursor.
2) Operate the cursor pad to shift the cursor.
Shifting the Display
1) Press CURSOR ON/OFF to turn off the
cursor.
2) Operate the cursor pad to shift the display.
Press the CENTER key to shift own ship to
the center of the display.
Centering Cursor Position
1) Press CURSOR ON/OFF to turn on the
cursor.
2) Operate the cursor pad to position the cur-
sor where desired.
3) Press CENTER.
Entering/Erasing Marks
1) Press CURSOR ON/OFF to turn on the
cursor.
2) Operate the cursor pad to position the cur-
sor where you wish to enter a mark.
3) Press MARK.
To erase any mark (except MOB), place
the cursor on the mark and press CLEAR.
2
This manual is printed with
soy ink.
Selecting Mark Shape/Line
Type
1) Press MENU ESC and 2.
2) Press ▲ or ▼ to select Mark Shape (or
Mark Line).
3) Press ◄ or ► to select mark shape (or
mark line) desired.
4) Press NU/CU ENT.
5) Press MENU ESC.
Entering Event Mark
Press EVENT MOB momentarily.
Entering MOB Mark
1) Press EVENT MOB (about three seconds)
until “Save MOB position” appears.
2) Press NU/CU ENT.
Starting/Stopping Plotting and
Recording of Track
Press PLOT ON/OFF. “
H
” appears when
recording is disabled. “
H
” disappears when
recording is enabled.
Registering Waypoints
A waypoint can be entered by several ways.
Below is the procedure for entry by the
cursor.
1) Press WPT RTE.
2) Press 1 to select Cursor.
3) Operate the cursor pad to place the cursor
on the position desired for a waypoint.
4) Press NU/CU ENT.
5) Press ▼ to select Mark column.
6) Press ◄ or ► to select mark shape.
7) Press NU/CU ENT.
8) Enter comment (maximum 12 alphanu-
meric characters).
9) Choose “ENTER” and press NU/CU ENT.
10)Press NU/CU ENT.
Registering Routes
1) Press WPT RTE.
2) Press 6 (5 for Dual) to select Route
Planning.
3) Press ▲ or ▼ to select route number.
4) Press ►.
5) Enter waypoint number (three digits).
6) Press ▼.
7) Repeat steps 5 and 6 to enter next
waypoint number.
8) Press MENU ESC twice to quite.
Setting/Cancelling Destination
Destination can be set by four ways. Below
is the method for setting destination by the
cursor.
1) Press GOTO.
2) Press 1 to select Cursor.
3) Place the cursor on the position to set as
destination.
4) Press NU/CU ENT twice.
To cancel destination, press GOTO, 5,
NU/CU ENT.
Setting the Arrival Alarm
1) Press MENU ESC and 4.
2) Press ▲ or ▼ to select Arrival/Anchor.
3) Press ◄ to select “Arr.”
4) Press ▼ to select “Alarm Range.”
5) Enter arrival alarm range.
6) Press NU/CU ENT.
7) Press MENU ESC.
The buzzer may be silenced by pressing
CLEAR.
PUB.NO.OSE-44400-A
(0602,HIMA) GP-150/DUAL
  • Page 1 1
  • Page 2 2

Furuno GP-150 User manual

Furuno
Brand
Furuno
Model
GP-150
Category
Navigators
Type
User manual

Furuno GP-150 is a high-performance GPS navigator designed for marine use. It offers various display modes, including plotter, 3D, highway, navigation, and data, allowing you to customize your view based on your needs. You can zoom in and out, shift the cursor and display, and center your own ship's position. The GP-150 enables you to set and cancel destinations, create and register routes, and mark important locations using various shapes and line types. It also features an event mark for MOB (Man Overboard) situations and an arrival alarm to alert you when approaching your destination.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents