Western Isolation Module Adapter Kit #26641-1 Installation guide

Western
Brand
Western
Model
Isolation Module Adapter Kit #26641-1
Type
Installation guide

Western Isolation Module Adapter Kit #26641-1 allows for easy installation of a snowplow on your vehicle. It includes a plug-in harness and adapter that connects to the headlamp connectors on the driver and passenger sides of the vehicle. The kit also includes dielectric grease to help protect the connections from corrosion. With this adapter kit, you can quickly and easily install a snowplow on your vehicle without having to worry about cutting or splicing any wires.

Western Isolation Module Adapter Kit #26641-1 allows for easy installation of a snowplow on your vehicle. It includes a plug-in harness and adapter that connects to the headlamp connectors on the driver and passenger sides of the vehicle. The kit also includes dielectric grease to help protect the connections from corrosion. With this adapter kit, you can quickly and easily install a snowplow on your vehicle without having to worry about cutting or splicing any wires.

Lit. No. 29209, Rev. 02 1 April 1, 2009
A DIVISION OR SUBSIDIARY OF DOUGLAS DYNAMICS, L.L.C.
26641-1 Adapter Kit
Installation Instructions
PLUG-IN HARNESS INSTALLATION
Follow the Isolation Module installation instructions
included with the harness kit until directed to use
these adapter kit instructions.
NOTE: For vehicles using the 8436 4-Port Harness
Kit, the short plug-in harness should be on the
same side of the vehicle as the Isolation Module
and both of the plug-in harnesses must be
confi gured for HB-5 headlamps (9007).
HB-5
9007
Plug-In
Harness
Connector
(HB-5 side up)
Adapter
Headlamp
Connector
PLUG-IN ADAPTER INSTALLATION
1. Remove the headlamp connectors on the driver
side of the vehicle.
2. On the two-pin connector removed from the
innermost headlamp, fi ll the terminals with
dielectric grease and cover connector with tape or
heatshrink tubing. This connector will not be used.
3. Apply dielectric grease to the terminals on the
three-pin plug removed from the headlamp. Plug
the molded three-pin male adapter plug into this
plug and cover both connectors with tape or
heatshrink tubing.
4. Plug the blue three-pin adapter connector into the
molded plug on the plug-in harness.
For vehicles using the 29050/B29050 harness,
connect the adapter as shown below:
5. Connect the adapter three-pin molded connector
to the blue three-pin connector on the plug-in
harness.
6. Repeat Steps 1–5 on the passenger side of the
vehicle.
26641-1
Lit. No. 29209, Rev. 02 2 April 1, 2009
The company reserves the right under its product improvement policy to change construction or design details and furnish equipment when
so altered without reference to illustrations or specifi cations used. This equipment manufacturer or the vehicle manufacturer may require or
recommend optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. The company offers a limited warranty for
all snowplows and accessories. See separately printed page for this important information.
Printed in U.S.A.
  • Page 1 1
  • Page 2 2

Western Isolation Module Adapter Kit #26641-1 Installation guide

Western
Brand
Western
Model
Isolation Module Adapter Kit #26641-1
Type
Installation guide

Western Isolation Module Adapter Kit #26641-1 allows for easy installation of a snowplow on your vehicle. It includes a plug-in harness and adapter that connects to the headlamp connectors on the driver and passenger sides of the vehicle. The kit also includes dielectric grease to help protect the connections from corrosion. With this adapter kit, you can quickly and easily install a snowplow on your vehicle without having to worry about cutting or splicing any wires.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents