2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Western
  6. Replacement Motor

Western Replacement Motor Installation guide

  • Hello! I've reviewed the provided document, which is an instruction manual for motor installation. It includes details on proper cable connections, torque specifications, and washer placements during motor replacement, and specifies that the ground cable must be connected correctly for the motor to operate. I'm ready to assist you with any questions you have about this document or the process described within it.
  • Where should the ground cable be connected?
    What should be done with the drain plug?
    What torque should be used for 7/16" x 1-1/4" cap screws?
7/16" x 1-1/4"
Cap Screws
180−240 in-lb
Boot Bracket
(if required)
Ground
Cable
(Black Cable)
50−60 in-lb
Black/Orange Wire
(if required) Ground cable MUST be connected
here for motor to operate.
50−60 in-lb
Positive Battery Cable
from Motor Relay
(Black w/Red Stripe or
Red Cable)
Remove plug from drain
hole used by original motor.
+
l
REPLACEMENT MOTOR INSTALLATION
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
7/16" x 1-1/4"
Cap Screws
180−240 in-lb
Boot Bracket
(if required)
Ground
Cable
(Black Cable)
50−60 in-lb
Black/Orange Wire
(if required) Ground cable MUST be connected
here for motor to operate.
50−60 in-lb
Positive Battery Cable
from Motor Relay
(Black w/Red Stripe or
Red Cable)
Remove plug from drain
hole used by original motor.
+
l
REPLACEMENT MOTOR INSTALLATION
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
7/16" x 1-1/4"
Cap Screws
180−240 in-lb
Boot Bracket
(if required)
Ground
Cable
(Black Cable)
50−60 in-lb
Black/Orange Wire
(if required) Ground cable MUST be connected
here for motor to operate.
50−60 in-lb
Positive Battery Cable
from Motor Relay
(Black w/Red Stripe or
Red Cable)
Remove plug from drain
hole used by original motor.
+
l
REPLACEMENT MOTOR INSTALLATION
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
7/16" x 1-1/4"
Cap Screws
180−240 in-lb
Boot Bracket
(if required)
Ground
Cable
(Black Cable)
50−60 in-lb
Black/Orange Wire
(if required) Ground cable MUST be connected
here for motor to operate.
50−60 in-lb
Positive Battery Cable
from Motor Relay
(Black w/Red Stripe or
Red Cable)
Remove plug from drain
hole used by original motor.
+
l
REPLACEMENT MOTOR INSTALLATION
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
1/4" x 6-1/4"
Cap Screws
35−45 in-lb
Thin fiber washers
(light color, quantity
varies) to end cap
Metal washer next
to commutator
One thick fiber washer
(dark color) to
pump shaft end
If armature is disassembled out of the motor frame, proper
washer placement is critical during reassembly.
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
1/4" x 6-1/4"
Cap Screws
35−45 in-lb
Thin fiber washers
(light color, quantity
varies) to end cap
Metal washer next
to commutator
One thick fiber washer
(dark color) to
pump shaft end
If armature is disassembled out of the motor frame, proper
washer placement is critical during reassembly.
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
1/4" x 6-1/4"
Cap Screws
35−45 in-lb
Thin fiber washers
(light color, quantity
varies) to end cap
Metal washer next
to commutator
One thick fiber washer
(dark color) to
pump shaft end
If armature is disassembled out of the motor frame, proper
washer placement is critical during reassembly.
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
1/4" x 6-1/4"
Cap Screws
35−45 in-lb
Thin fiber washers
(light color, quantity
varies) to end cap
Metal washer next
to commutator
One thick fiber washer
(dark color) to
pump shaft end
If armature is disassembled out of the motor frame, proper
washer placement is critical during reassembly.
Lit. No. 13645, Rev. 03 Printed in U.S.A. November 15, 2007
/