Nucraft Forena™ Installation guide

Type
Installation guide

Nucraft Forena™ is a refrigeration appliance designed to be installed within existing cabinetry. It features adjustable drawer fronts, trim pieces to cover gaps between the fridge and cabinetry side panels, and a power cord with cord clips for easy installation. The installation process requires basic tools such as a drill driver, Phillips bit, and optionally a Vix bit for predrilling trim bracket holes. The provided hardware includes installation brackets, trim brackets, pan head screws, installation trims, a power cord, an outlet duct, and drawer panel attachment hooks.

Nucraft Forena™ is a refrigeration appliance designed to be installed within existing cabinetry. It features adjustable drawer fronts, trim pieces to cover gaps between the fridge and cabinetry side panels, and a power cord with cord clips for easy installation. The installation process requires basic tools such as a drill driver, Phillips bit, and optionally a Vix bit for predrilling trim bracket holes. The provided hardware includes installation brackets, trim brackets, pan head screws, installation trims, a power cord, an outlet duct, and drawer panel attachment hooks.

Forena Fridge Installation Instructions
ID:099
**NOTE: Installers are to use Nucraft supplied Installation Instructions,
NOT manufacturers instructions.**
Before Beginning Installation
Read through the entire instruction thoroughly
A minimum of 1 person is required for this assembly
These instructions reflect typical assemblies. They may not match your specific configuration.
Required Tools
Drill Driver
Phillips Bit
Optional: Vix bit to predrill trim bracket holes
Provided Hardware
Installation Brackets (left and right hand sides)(1 Pair)
Phillips 16mm wood screw (12)
Trim Brackets (4)
Pan Head 16mm screw (14)
Installation Trims (2)
Power Cord (1)
Outlet Duct (1)
Drawer panel attachment hooks (3)
Step 1: Install Brackets
Mount installation brackets to lower
corners of open module. Be sure to
locate the front of the bracket 25mm’s
behind panel fronts.
Use (3) Philips 16mm wood screws per
bracket.
Ensure screw heads are flush with
bracket.
Step 2: Trim Brackets
Evenly space trim brackets on
the side of the Fisher&Paykel
fridge. Attach using 16mm pan
head screws in the two holes
located on the backside of the
bracket.
NOTE:
Do not attach the bracket
to the drawer of the
Fisher and Paykel fridge.
Orientation of the bracket
in the figure below.
Do not screw in trim
brackets to the case at this
time.
Step 3: Power Cord
Attach power cord to Fisher&Paykel
fridge unit utilizing provided cord
clips.
Run (Plug) end of power cord
through the cutout on the lower
backside of the partition, then down
through the cutout in the bottom
panel to the power supply.
(DO NOT PLUG IN UNTIL FINSHED)
Place Fisher&Paykel fridge into
open module
Step 4: Fridge Vent
Ensure fridge vent opening aligns with
cutouts in the bottom panel of the open
module.
Cut outlet duct to fit any gap between
bottom panel and fridge vent.
(IF NEEDED)
Secure using 16mm pan head screws
Ensure air will be properly ventilated out
of the cavity as shown.
Step 5: Attachment Hooks
Attach drawer panel attachment hooks to the
backside of drawer fronts using 16mm pan
head screw in predrilled location holes
Step 6: Drawer Fronts
Attach drawer fronts by placing the
drawer front attachment hooks into the
front channel.
Close drawer to check alignment and
clearances.
Adjust top attachment, using set screw
in the hook, to align fronts.
Open drawer to secure panel in place by
tightening bottom attachment hook.
Step 7: Trim Pieces
Open Fisher&Paykel fridge door.
Attach screw trim brackets into case
using (1) 16mm pan head screw per
bracket.
Attach trim pieces to both side
panels.
Note: Trim pieces will sit at an angle
to cover the gap between the fridge
and the cabinetry side panels.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Nucraft Forena™ Installation guide

Type
Installation guide

Nucraft Forena™ is a refrigeration appliance designed to be installed within existing cabinetry. It features adjustable drawer fronts, trim pieces to cover gaps between the fridge and cabinetry side panels, and a power cord with cord clips for easy installation. The installation process requires basic tools such as a drill driver, Phillips bit, and optionally a Vix bit for predrilling trim bracket holes. The provided hardware includes installation brackets, trim brackets, pan head screws, installation trims, a power cord, an outlet duct, and drawer panel attachment hooks.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI