Bray Series 940 Unidirectional Knife Gate Valve Owner's manual

Brand: Bray

Model: Series 940 Unidirectional Knife Gate Valve

Type: Owner's manual

SERIES 940

UNIDIRECTIONAL KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

BRAY.COM THE HIGH PERFORMANCE COMPANY

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

0.0 Deﬁnition of Terms 3

1.0 Introduction 4

2.0 Parts Identiﬁcation 5

3.0 Valve Identiﬁcation 6

4.0 Hazard-Free Use 7

5.0 Qualiﬁed Personnel 8

6.0 Handling Requirements 9

7.0 Lifting 10

8.0 Storage 12

9.0 Installation & Commissioning 14

10.0 Actuation and Travel Stop Setting 17

11.0 Lockout 18

12.0 Standard Maintenance 19

13.0 Packing Replacement - Manual Operated Valves 21

14.0 Packing Replacement - Cylinder Operated Valves 22

15.0 Seat Replacement 24

16.0 Retro Fitting Cylinder Actuator 25

17.0 Troubleshooting Guide 26

18.0 Return Merchandise Authorization 27

TABLE OF CONTENTS

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

0.0 DEFINITION OF TERMS

All information within this manual is relevant to the safe operation

and proper care of your Bray valve. Please understand the

following examples of information used throughout this manual.

0.0 IDENTIFIES CHAPTER HEADING

0.00 Identiﬁes and explains sequential procedure to be performed.

NOTE: Provides important information related to a procedure.

SAFETY STATEMENTS: To prevent unwanted consequences.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

NOTICE

Used without the safety alert symbol, indicates a potential

situation which, if not avoided, may result in an undesirable

result or state, including property damage.

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY.

SAVE THIS MANUAL FOR FUTURE USE.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

1.0 INTRODUCTION

1.1 The Bray Knife Gate Series 940’s one-piece, cast body design

oers rugged performance in applications ranging from general

purpose to severe media handling. Available with integral metal or

replaceable soft seat, the Bray Knife Gate Series 940 gate valve is

easily automated for on/o applications.

1.2 Additional product information (such as application data,

engineering speciﬁcations, actuator selection, etc.) is available

from your local Bray distributor or sales representative, or online

at BRAY.COM

1.3 For complete details on the latest product certiﬁcations,

visit BRAY.COM/Certiﬁcations.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

Figure 1: Series 940 Parts

Item Description

1 Body

2Gate

3 Packing Set

4 Gland

5 Gland Bolt

6 Gland Washer

7 Gland Nut

8Yoke

9 Mounting Bolt (Top)

10 Mounting Nut (Top)

11 Mounting Nut (Bottom)

12 Spring Washer

13 Clevis

14 Stem

15 Clevis Bolt

16 Clevis Nut

17 Collar

18 Yoke Sleeve

19 Grease Nipple

20 Thrust Washer

21 Hand Wheel

22 Socket Screw

23 Seat1

2.0 PARTS IDENTIFICATION

NOTE

1 Optional replaceable resilient seat.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

3.0 VALVE IDENTIFICATION

3.1 All valves, actuators, or control products are provided with an

identiﬁcation tag that is unique to each device. The following

table is a representation of information that may be included.

Data Label Description

Serial Number SERIAL NUMBER Unique serial number of valve

Valve Size SIZE Valve size eg  in mm

Model MODEL Series number of the Valve

Flange Drill FLG DRILL Flange Drill eg ASME B

CL

Temperature Limits MAX TEMP Maximum temperature in

FC

Maximum Permissible

Pressure CWP Maximum permissible pressure

in psibar(g)

Body Material BODY Material grade of body eg

CF () etc

Gate Material GATE Material grade of gate eg 

Stainless Steel

Packing Material PACKING Material of packing eg PTFE

wEPDM Quad Seal

Seat Material SEAT Material of seat eg Buna-N

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

4.0 HAZARD-FREE USE

NOTICE

Failure to follow these procedures could aect product warranty.

4.1 This device left the factory in proper condition to be safely

installed and operated in a hazard-free manner. The notes and

warnings in this document must be observed by the user if this

safe condition is to be maintained and hazard-free operation of

the device assured.

4.2 Take all necessary precautions to prevent damage to the valve

due to rough handling, impact, or improper storage. Do not use

abrasive compounds to clean the valve, or scrape metal surfaces

with any objects.

4.3 The control systems in which the valve is installed must have

proper safeguards — to prevent injury to personnel, or damage to

equipment — should failure of system components occur.

4.4 The upper limits of permitted pressure and temperature

(depending on the housing and liner materials) must be

observed. These limits are shown on the valve identiﬁcation tag.

4.5 The valve must not be operated until the following documents

have been observed:

> Declaration on EU Directives

> IOM Manual (supplied with the product).

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

5.0 QUALIFIED PERSONNEL

NOTICE

Failure to follow these procedures could aect product warranty.

5.1 A qualiﬁed person (in terms of this document) is one who is

familiar with the installation, commissioning, and operation of the

device, and who has appropriate qualiﬁcations, such as:

> Is trained in the operation and maintenance of electrical

equipment and systems in accordance with established safety

practices.

> Is trained or authorized to energize, de-energize, ground, tag,

and lock electrical circuits and equipment in accordance with

established safety practices.

> Is trained in the proper use and care of personal protective

equipment (PPE) in accordance with established safety

practices.

> Is trained in the commissioning, operation, and maintenance of

equipment in hazardous locations — in cases where the device

is installed in a potentially explosive (hazardous) location.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

6.0 HANDLING REQUIREMENTS

6.1 Packed Valves

Crates: Lifting and handling of the packed valves in crates will be

carried out by a fork lift truck, by means of the appropriate fork

hitches.

Cases: The lifting of packed valves in cases will be carried out in

the lifting points and in the center of gravity position which has

been marked. The transportation of all packed material must be

carried out safely and following the local safety regulations.

6.2 Unpacked Valves

Lifting and handling of valves should be carried out by using

appropriate means and observing the carrying limits. Handling

must be carried out on pallets, protecting all machined surfaces

to avoid any damage.

With large bore valves, rigging the load must be carried out by

using the appropriate tools to prevent the valve from falling or

moving during the lifting and handling.

CAUTION

For handling and/or lifting, the lifting equipment (fasteners,

hooks, etc.) must be sized and selected while taking into account

the product weight indicated in our packing list and/or delivery

note. Lifting and handling must be performed only by qualiﬁed

personnel.

Fasteners must be protected by plastic covers in sharp corner

areas.

Caution must be taken during handling to avoid this equipment

passing over workers, or over any other place where a possible

fall could cause injury or damage. In all cases, local safety

regulations must be respected.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

7.0 LIFTING THE VALVE

WARNING

A potential hazard exists with handling valves. Failure to handle

valves properly may cause a valve to shift, slip or fall causing

serious injury or death and/or equipment damage.

7.1 The points below are for reference purposes only, use safe and

proper lifting and support techniques. DO NOT lift valves with

any adjoining pipe or other equipment attached. Lift with

properly rated lifting equipment. Follow jurisdictional safety

requirements.

7.2 Suggested lifting points are as shown below to lift valve

assemblies that are in a horizontal orientation. Eye bolts in ﬂange

through holes can be used to lift the valve body or, for 2” through

12” valves, a sling can be strapped around the top of the valve

body.

7.3 KNIFE GATE VALVE WITH BEVEL GEAR ACTUATOR:

For valves with bevel gear actuators, a sling or chain can be

wrapped around the bevel gear actuator body, between the

mounting plate and the input shaft housing. This would be in

conjunction with lifting from the valve body as well. See Figure 2.

Figure 2: Knife Gate Valve with Bevel Gear Actuator,

Horizontal Lifting

7.4 KNIFE GATE VALVE WITH PNEUMATIC CYLINDER ACTUATOR:

For valves with pneumatic cylinder actuators, a sling can be

wrapped around the cylinder, near the cylinder head (piston rod

end). This would be in conjunction with lifting from the valve

body. See Figure 3.

7.5 Utilize caution to not bump, dent or damage the cylinder tube.

7.6 DO NOT utilize the cylinder tie-rod ends to lift.

Figure 3: Knife Gate Valve with Pneumatic Cylinder Actuator,

Horizontal Lifting

(continued)

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

7.7 KNIFE GATE VALVE WITH HANDWHEEL ACTUATOR:

For valves with handwheel actuators, a sling or chain can be

wrapped through the rim of the handwheel. For chain wheel

actuators, a sling can be wrapped in the area between the yoke/

legs and the chain-wheel/guide assembly. This would be in

conjunction with lifting from the valve body as well. See Figure 4.

Figure 4: Knife Gate Valve with Handwheel, Horizontal Lifting

7.8 Suggested lifting options are as shown below to lift valve

assemblies that are in a vertical orientation. For valves with bevel

gear actuators, wrap slings or chains around the top of each leg.

NOTE: Use caution not to put any side load on the bevel gear

input shaft or on the valves threaded stem. See Figure 5.

7.9 For valves with pneumatic cylinder actuators, wrap slings around

the top of each leg. Use caution to not bump, dent or damage the

cylinder tube and avoid any side load on the cylinder piston rod.

NOTE: DO NOT utilize the cylinder tie-rod ends to lift. See Figure 6.

7.10 For valves with handwheel or chain-wheel actuators, wrap slings

or chains around the top of the each leg or yoke side.

NOTE: Use caution to not put any side load on the valves

threaded stem. See Figure 7.

Figure 7: Knife Gate Valve with

Handwheel, Vertical Lifting

Figure 6: Knife Gate Valve with

Pneumatic Cylinder Actuator,

Vertical Lifting

Figure 5: Knife Gate Valve w/Bevel

Gear Actuator, Vertical Lifting

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

8.0 STORAGE

NOTICE

The packaging is designed to protect the valve only during

shipping. If you are not installing the valve immediately after

delivery, then you must store it according to these requirements.

Failure to follow these procedures could aect product warranty.

8.1 Short-term storage is deﬁned as storage of valves to allow for

project construction and will be installed within a relatively short

amount of time (typically one to three months). During short-term

storage, the following is required:

8.2 The preferred storage location is a clean, dry, protected

warehouse. Do not expose the valve to temperature extremes.

8.3 End protectors shall remain on the valve ends to prevent the

entrance of dirt, debris, or insects/wildlife.

8.4 Remain in the original shipping container with the original

packaging materials. This packaging method will not protect

valves that will be stored outside, uncovered, and unprotected.

8.5 Storage of valves in an open, uncovered area is permissible, but

requires provisions for inclement weather. The product must

elevated from the ground on a pallet, a shelf, or other suitable

surface, and must be covered with a secure, waterproof tarp.

8.6 Do not stack the valves on top of each other.

8.7 Manually actuated valves may be stored in the vertical or

horizontal position. For air or hydraulic actuated valves, the

preferred orientation is with the valve and cylinder in the vertical

position. Access ports should be secured to prevent unauthorized

entry and prevent contamination.

(continued)

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

8.8 Long-term storage is deﬁned as storage of valves longer than

three months. During long-term storage, the following is required:

8.9 The storage location shall be a clean, dry, protected warehouse.

Do not expose the valve to temperature extremes.

8.10 End protectors shall remain on the valve ends to prevent the

entrance of dirt, debris, or insects/wildlife.

8.11 Product shall remain in the original shipping container with the

original packaging materials.

8.12 Do not stack the valves on top of each other.

8.13 Manually actuated valves may be stored in the vertical or

horizontal position. For air or hydraulic actuated valves, the

preferred orientation is with the valve and cylinder in the vertical

position. Access ports should be secured to prevent unauthorized

entry and prevent contamination.

Valves and equipment containing elastomers, including O-rings,

must be stored in a climate-controlled warehouse according to

SAE-ARP5316D requiring:

> The ambient relative humidity to be less than 75%.

> No exposure from direct ultraviolet or sunlight.

> Protection from ozone generating equipment or combustible

gases and vapors.

> Storage at temperatures below 100°F (38°C), away from direct

sources of heat.

> No exposure to ionizing radiation.

Storage inspection — visual inspection shall be performed on a

semi-annual basis and results recorded. Inspection, as a minimum,

shall include reviewing the following:

> Packaging.

> Flange covers.

> Dryness.

> Cleanliness.

8.14 Actuators to be stored with all cable/pneumatic entries plugged

to prevent entry of foreign material.

8.15 Leave protective caps and covers on the product.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

9.0 INSTALLATION AND COMMISSIONING

WARNING

Verify line is depressurized before installing, removing, or

repairing a valve or operator.

Do not pressurize the line without an operator on the valve.

The device generates a large mechanical force during normal

operation.

Observe all applicable safety regulations for valves installed in

potentially explosive (hazardous) locations.

9.1 The valve is unidirectional. It should be installed with pressure

exerted against the seat. To enable correct orientation the word

“SEAT” is marked on the valve body to indicate the position of

the valve seat.

9.2 It is good practice to provide additional support for all

pneumatically, hydraulic and electric actuated valves installed in

the horizontal stem position. This includes ALL valve sizes due

to the fact that many of these installations are located in high

vibration areas. Failure to provide additional support will result in

premature valve failure.

9.3 It is recommended to provide support around areas indicated in

Figures 8 and 9 with an adjustable sling.

9.4 Support from the top as shown or with suitable arrangement

from bottom (such as from an access platform) depending on

location constraints.

9.5 After the support is given, please operate the valve a few times

to check free movement and adjust the level (using the sling

adjuster or similar device) if required.

9.6 Ensure jerk free movement with the supports in place.

(continued)

Figure 8: Installation support for

a Valve installed in Horizontal

orientation (Stem horizontal and

Bore horizontal)

Figure 9: Installation support for

a Valve installed in Horizontal

orientation (Stem horizontal and

Bore vertical)

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

9.7 Align the mating pipeline ﬂanges. Select the length of the ﬂange

bolts as seen in Table 1 and Table 2 below. Install the valve

between ﬂanges using fasteners & gaskets.

9.8 Tighten ﬂange bolts in a star pattern. See Figure 14.

9.9 Refer to GA Drawing/ Technical Bulletin for quantity and size of

blind tapped holes on valve chest area.

Figure 12: L7 Lug Stud

Figure 13: L8 Chest Stud

Figure 10: L5 Lug Bolt

Figure 11: L6 Chest Bolt

Table 1: RECOMMENDED FASTENERS - ASME B16.5 Class 150 Flanges

L5 (Figure 10) L6 (Figure 11)

Valve Size Bolt & Nut

Size Lug Bolt

Length Lug Bolt

Qty Chest Bolt

Length Chest Bolt

Qty Washer*

Quantity

NPS DN NPS

2 50 -     

3 80 -     

4 100 -     

5 125 -     

6 150 -     

8 200 -     

10 250 -     

12 300 -     

14 350 -     

16 400 -     

18 450  -     

20 500  -     

24 600  -     

* Washer Type B Wide

Table 2: RECOMMENDED FASTENERS - ASME B16.5 Class 150 Flanges

L7 (Figure 12) L8 (Figure 13)

Valve Size Bolt & Nut

Size Lug Bolt

Length Lug Bolt

Qty Chest Bolt

Length Chest Bolt

Qty Nut

Qty Washer*

Qty

NPS DN NPS NPS

2 50 5/8-11 2.5 4 2.25 4 8 8

3 80 5/8-11 2.5 4 2.5 4 8 8

4 100 5/8-11 2.5 12 2.5 4 16 16

5 125 3/4-10 2.8 12 2.5 4 16 16

6 150 3/4-10 3.0 12 2.5 4 16 16

8 200 3/4-10 3.0 12 2.75 4 16 16

10 250 7/8-9 3.5 16 2.75 824 24

12 300 7/8-9 3.5 16 3.0 824 24

14 350 1-8 4.0 16 3.5 8 24 24

16 400 1-8 4.0 20 3.5 12 32 32

18 450 1 1/8-7 4.5 20 4.0 12 32 32

20 500 1 1/8-7 4.5 24 4.5 16 40 40

24 600 1 1/4-7 5.0 24 4.5 16 40 40

* Washer Type B Wide

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

9.10 Gland packing is tightened to hold the speciﬁed pressure and

tested for no leakage in the factory. Gland packing is then

loosened before dispatch to prevent compression during transit

and storage.

9.11 Tighten packing gland in a crisscross pattern until the packing

ring at the top is slightly compressed.

9.12 Pressurize the valve gradually and stop when packing leak is

visible or design pressure is reached.

9.13 Re-tighten packing gland bolts just enough to stop the leakage.

If maximum design pressure is not reached, continue to

pressurize the valve and repeat steps 9.11 and 9.12.

Figure 16: Flange Bolting

NOTE: To determine bolt length for the blind

holes in the upper chest area of the valve,

add thread depth+ gasket + ﬂange thickness

+ any washers (plus deﬂection cone and

gasket when used)

Figure 15: Bolt holes in the chest or

upper ﬂange area are blind tapped

CAUTION

Support should be used for all valve sizes when installed in

vertical pipe. Failure to do so can result in improper valve

orientation and/or valve failure. Please consult factory for details.

CAUTION

Care must be taken when installing the studs or bolts in the

tapped holes of the ﬂange in the chest area to prevent damage,

see Figure 15 and Figure 16.

CAUTION

If the gland nuts are pulled too hard, the force needed to operate

the valve will increase, the valve function will be aected and the

box packing lifetime will be shortened.

CAUTION

Incorrect electrical supply to accessories will damage the

equipment.

CAUTION

Do not over tighten the gland nuts as this may cause excessive

friction and premature damage to packing.

Figure 14: Bolt Tightening

Sequence

2 5

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

10.0 ACTUATION AND TRAVEL STOPS

WARNING

Verify line is depressurized before installing, removing, or

repairing a valve or operator.

Do not pressurize the line without an operator on the valve.

10.1 PNEUMATIC CYLINDER OPERATED VALVES

10.2 In Figure 17, connect instrument quality air, preferably through an

air ﬁlter/regulator of adequate size.

10.3 The recommended air pressure is 50-100 psi (3.5-7 bar). Refer

to the appropriate bulletin/drawing for port and cylinder size

details.

10.4 Make sure the supply air is free from moisture, dirt, and other

foreign particles.

10.5 Drain the ﬁlter regulator before operating the actuator so that

pipe rust and dirt if any in the air line will be removed before

actuation.

10.6 If valves are supplied with electrical accessories like limit switch

and solenoid valve, ensure wiring is done as per local electrical

safety codes and regulations.

10.7 Ensure correct electrical supply is given to electrical accessories

for proper functioning and safety of the equipment.

10.8 Open the valve by energizing the solenoid valve/giving air supply

to cylinder and operate the valve 2-3 times.

10.9 MANUAL VALVES

10.10 For Figure 18, Stroke the valve through the full open and closed

position to make sure it is functioning properly.

Figure 17: Cylinder Actuator

Figure 18: Manual Valve Stem

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

11.0 LOCKOUT

11.1 Lockouts, Figure 19 and 20, are designed to prevent

unauthorized operation of the valve. The instructions below are

intended for personnel who are responsible for the installation,

operation and maintenance of the lockout device for Bray knife

gate valves.

11.2 Any actuated valve (Pneumatic or Hydraulic or Electric) must

be placed in a “De-energized state” by isolating all potential

energy sources including electricity, operator supply air or

hydraulic ﬂuids.

11.3 Valves supplied with spring to close or open contain mechanical

springs in the cylinder and hence cannot be placed in a de-

energized state. Take extreme care when inserting and removing

the lockout pin to avoid any injury to operating personnel.

11.4 For mechanical lockout or full force lockout, where the lockouts

are meant to hold the full actuator force, please contact factory

for assistance and more information.

CAUTION

Once the lockout pins are in place in the lockout brackets, any

Bray actuated valve MUST be placed in a “De-energized state”

by isolating the supply air / hydraulic ﬂuid / electricity.

CAUTION

The lockout device could get damaged when actuator thrust is

applied with the Lockout pin engaging the Gate.

Figure 19: Lockout pin through

yoke and handwheel.

Figure 20: Lockout pin through

C Bracket.

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

12.0 STANDARD MAINTENANCE

WARNING

Verify line is depressurized before installing, removing, or

repairing a valve or operator.

Do not pressurize the line without an operator on the valve.

WARNING

After completing any alterations or maintenance procedures, the

product must be tested to conﬁrm performance requirements.

WARNING

When the process ﬂuid is hazardous, thermal (hot or cold), or

corrosive, take extra precautions.

WARNING

Always wear protective clothing and equipment to safeguard

the eyes, face, hands, skin, and lungs from the particular ﬂuid in

the line.

NOTICE

Any modiﬁcation or use of unauthorized parts voids any and all

warranty considerations.

NOTICE

Note assembly positions before removal.

CAUTION

Disconnect electrical, pneumatic, and hydraulic power before

servicing actuator or automation components.

12.1 The stem and nut of the knife gate valve are lubricated at the

factory before shipment.

12.2 The manual valve stem should be lubricated at regular intervals for

smooth operation of the valve. A lubrication nipple is provided on

the collar. See Lubrication requirements in Table 3.

12.3 Cylinder operated valves do not require routine lubrication.

(continued)

Table 3: Recommended Lubrication

Lubricant Type

Industrial Grease - Medium

C5 - A Compound

XL 47 - F2 - 75

Molytex Grease #2

SERIES 940 UNIDIRECTIONAL KNIFE GATE VALVE

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

NOTICE

If the cylinder actuator is disassembled for repair, the cylinder

wall and seals need to be lubricated with a lithium-based grease

prior to reassembly.

12.4 Parts recommended as spares as shown in Table 4, may be

stocked. Provide the valve serial number and work order number

from the nameplate for proper parts.

12.5 We recommend that all 940 knife gate valves be inspected at

least every 60 days. The following points should be examined and

corrected as required:

1. Exterior overview: As piping system components are subject to

varying levels of erosion and corrosion, periodic inspections should

be made as valves/components may wear over time. Regular

inspection of the valve body and gate should be performed, check

for general signs of corrosion, component wear and/or damage

caused by process media and atmospheric conditions.

2. Packing gland: Check for leaks or worn packing. If leakage is

occurring around the packing gland, tighten the packing gland

bolts, being careful not to over stress the bolting.

3. If possible stroke the valve through the full open and closed

position to make sure it is functioning properly.

Table 4: Recommended Spare Parts

Part Qty

Gland Packing Set of 3 Rows

Spare Seat 1

Cylinder Repair Kit 1

Gate 1

Page is loading ...

Bray Series 940 Unidirectional Knife Gate Valve Owner's manual

Bray Series 940 Unidirectional Knife Gate Valve Owner's manual

Bray Series 940 Unidirectional Knife Gate Valve Owner's manual

Related papers

Other documents