USG DUROCK
®
BRAND CEMENT
BOARD WITH EDGEGUARD
™
Installation Guide
USG
Tile &
Flooring
Solutions
USG DUROCK
®
BRAND
CEMENT BOARD WITH
EDGEGUARD
™
For more than 30 years, USG Durock® Brand Cement
Board has set the standard for proven performance in
the backerboard category. The new USG Durock® Brand
Cement Board with EdgeGuard™ o ers enhanced,
proprietary edge performance and minimizes spin-out
and crumbling. USG Durock® Brand Cement Board with
EdgeGuard™ installs quickly and easily, while maintaining the
brand’s tradition of quality and reliability.
Benefi ts include:
• Enhanced edge performance
• Easy to cut and fasten
• Water durable and mold resistant
• Exceptional tile bond
• Noncombustible
• Warranted for interior and exterior application
Water durable and mold resistant, with better tile bond
than fi ber-cement boards or bare plywood, USG Durock®
Brand Cement Board with EdgeGuard™ cement board is
an outstanding backerboard for a wide variety of reasons.
Choose this high-performance alternative to fi ber-cement
boards or bare plywood surfaces for:
Superior Tile Bond
Prevents tile pops and grout cracks, up to
40% greater tile bond than fi ber-cement board.
The Strength of Portland Cement
Will not swell, soften, rot, warp, delaminate or disintegrate
if exposed to water. Noncombustible. Backed by a 30-year
limited warranty.
Superior Mold Resistance
Receives rating of “0” for no mold growth as tested per
ASTM G21. Scores a 10 out of 10 on ASTM D3273.
3
WHAT YOU’LL NEED
Floors thickness 1/4 in.
(6 mm), 1/2 in. (12.7 mm),
5/8 in. (16 mm)
Subfl oor should be minimum
5/8 in. (16 mm). APA span-
rated plywood or OSB with
an Exposure 1 classifi cation
or better.
Countertops 1/4 in. (6 mm),
1/2 in. (12.7 mm), 5/8 in.
(16 mm) thickness
Minimum 3/4 in. (19 mm).
APA span-rated plywood
or OSB with an Exposure 1
classifi cation or better.
Cover base with USG
Durock™ Brand Tile
Membrane, 15 lb. (6.8 kg)
felt or 4-mil polyethylene
and attach with 1/4 in.
(6 mm) galvanized staples.
Walls and Ceilings 1/2 in.
(12.7 mm) and 5/8 in.
(16 mm) thickness only
Maximum stud spacing:
16 in. (406 mm) o.c. Maximum
allowable defl ection, based
on stud properties only,
L/360. Maximum fastener
spacing: 8 in. (203 mm) o.c.
for wood and steel framing;
6 in. (152 mm) o.c. for
ceiling applications.
Waterproofi ng
If waterproofi ng is desired,
use USG Durock™ Brand
Waterproofi ng Membrane or
USG Durock™ Brand Liquid
Waterproofi ng Membrane.
See USG Durock™ Brand
Waterproofi ng Membrane
submittal sheet (CB595) or
USG Durock™ Brand Liquid
Waterproofi ng Membrane
submittal sheet (CB817)
for product information.
Cutting
USG Durock® Brand Cement
Board with EdgeGuard™
panels should be cut to size
with a knife and straightedge.
A power saw should be used
only if it is equipped with
a dust collection device.
Always wear a NIOSH/MSHA-
approved mask and eye
protection when cutting
USG Durock® Brand panels.
• Utility knife: Using a
straightedge, score panel
face with utility knife and
cut through glass-fi ber
reinforcing mesh, then snap
and cut backside mesh to
break cleanly. Use a rasp to
smooth any rough edges.
• Power saw: Use a low-RPM
portable saw with 3-1/2 in.
(89 mm) carbide-tipped
blade. To make cutouts for
pipes and fi xtures, use utility
knife to cut through mesh
on both sides of panel and
punch out with a hammer
from back side. Or, use
an electric drill with a
hole-saw bit.
WARNING: Dust can contain silica.
Prolonged breathing can cause
lung damage and cancer. See SDS
for more information.
4
Floor Installation
1/4 in. (6 mm), 1/2 in.
(12.7 mm), 5/8 in.
(16 mm)
POSITIONING
Fit ends and edges of
panels closely but not forced
together, maintaining 1/4 in.
(6 mm). space between
panels and perimeter walls.
Stagger joints a minimum
16 in. (406 mm) so four
corners never meet. O set
panel joints a minimum
8 in. (203 mm) from
subfl oor joints.
16 in. 16 in.
1/4 in. gap
cut
edge
factory edges
underlayment
subfloor
LEVELING BED
Apply Type 1 organic
adhesive with 5/32 in.
(5 mm) v-notched trowel,
latex-fortifi ed mortar with
1/4 in. (6 mm). square-notched
trowel. Comb out adhesive
or mortar in straight, parallel
rows (as shown below) and
immediately cover with
panel. Adhere panels to
subfl oor, one panel at a time.
FASTENING
Secure panels while adhesive
is still wet. Space fasteners
8 in. (203 mm) o.c. around
the perimeter and in the
fi eld of the board.
Wood framing and
countertops: fasten with
1-1/2 in. (38 mm) 11-gauge
hot-dipped galvanized
roofi ng nails, or USG Durock™
Brand Tile Backer Screws for
wood framing or 1-1/4 in.
(32 mm) USG Durock™ Brand
Tile Backer Screws for wood
framing or equivalent.
JOINING
Fill joints with latex-fortifi ed
mortar or Type 1 organic
adhesive and immediately
embed alkali-resistant,
fi berglass mesh joint tape.
FINISHING
Tile or almost any fl ooring
material.*
*Not for use with vinyl fl ooring.
5
Countertop
Installation
1/4 in. (6 mm), 1/2 in.
(12.7 mm), 5/8 in.
(16 mm)
Cover plywood base with
USG Durock™ Brand Tile
Membrane, 15 lb. (6.8 kg) felt
or 4-mil polyethylene and
attach with 1/4 in. (6 mm)
galvanized staple.
POSITION
Fit ends and edges of panels
closely but not forced
together. Stagger panel joints
from plywood base joints.
FASTEN
Space fasteners 8 in.
(203 mm) o.c. around the
perimeter and in the fi eld
of the board.
JOINING
Fill joints with latex-fortifi ed
mortar or Type 1 organic
adhesive and immediately
embed alkali-resistant,
fi berglass mesh joint tape.
FINISH
Install tile.
Note: Because cement board
fasteners may protrude through
the plywood base when 1/4 in.
(6 mm) cement board is used,
1/2 in. (12.7 mm) or 5/8 in. (16 mm)
cement board is preferred in this
application.
Wall & Ceiling
Installation
1/2 in. (12.7 mm) &
5/8 in. (16 mm) only
FASTENING
Fasten to studs spaced
16 in. (406 mm) o.c. Space
fasteners 8 in. (203 mm)
o.c. for walls, 6 in. (152 mm)
o.c. for ceilings. Fit ends and
edges of panels closely but
not forced together.
• Wood framing: 1-1/2 in.
(38 mm) hot-dipped
galvanized roofi ng nails
or 1-1/4 in. (32 mm). USG
Durock™ Brand Tile Backer
Screws for wood framing
or equivalent.
• Steel framing: 1-1/4 in.
(32 mm) USG Durock™
Brand Tile Backer Screws
for steel framing or
equivalent.
JOINING
Fill joints with latex-fortifi ed
mortar or Type 1 organic
adhesive and immediately
embed alkali-resistant,
fi berglass mesh joint tape.
SHIM
Place a 1/4 in. (6 mm) spacer
strip or shim around lip of
bathtub or shower pan to
hold bottom edge of panel
o t h e fi x t u r e .
FINISH
Install tile.
See SA932EG for fi nishing
recommendations to nontiled
cement board.
6
Planning Your Tile
Installation
1/4 in. (6 mm), 1/2 in.
(12.7 mm), 5/8 in. (16 mm)
POSITIONING
Where tile will not cover
entire wall surface, such
as above tub and shower
surrounds, determine where
you want the tile to end
and draw a level line at this
height. Be sure to allow
for height of tile cap, if
applicable.
height of tile
cap
cut
cut
cut
floor level
On walls where tile will reach
the fl oor, determine whether
fl oor is level by measuring
distance to desired tile height
on both sides of area to be
tiled. If there is a di erence
(e.g., the fl oor is lower on one
side), lay one vertical row of
tile from highest point down
to fl oor. A x tiles with dabs
of mastic.
Use this fi rst row as a guide
to keep tiles and grout lines
level and ensure alignment
with tiles of adjacent tub
or shower surround. If new
fl ooring will be installed,
leave a su cient gap
between lowest tile and
s u b fl o o r .
level line
level
horizontal starting
line
floor tile
vertical starting line
On bathroom fl oors, start by
placing full tiles in front of
bathtub or shower and along
the adjoining wall to avoid
cut tiles in this highly visible
area.
7
Installing
Ceramic Tile
Apply latex-fortifi ed mortar or
Type 1 organic adhesive with a
notched trowel. Hold trowel at
an angle to maintain uniform
thickness. Refer to setting
material manufacturer for
specifi c information related to
trowel type and size.
Working a small area at a
time, press tile into place
with a slight twisting motion
to seat properly. Prevent
adhesive buildup on tile edge
and in grout space. If adhesive
squeezes from under tile,
remove excess before it dries.
Keep tiles and joints straight
and uniform. Use tile spacers
if desired.
CUSTOMER SERVICE
800 621-9523
TECHNICAL SERVICE
800 USG.4YOU (874-4968)
PRODUCT INFORMATION
See usg.com/edgeguard for the most up-to-date product information.
DANGER
Causes skin irritation. Causes serious eye damage. May cause an
allergic skin reaction. May cause respiratory irritation. May cause
cancer by inhalation of respirable crystalline silica. Do not handle
until all safety precautions have been read and understood. Avoid
breathing dust. Use only in a well-ventilated area, wear a NIOSH/
MSHA-approved respirator. Wear protective gloves/protective
clothing/eye protection. If swallowed, inhaled, or skin irritation
occurs get medical attention. If on skin: Wash with plenty of water.
If in eyes: Rinse cautiously with water for several minutes. Remove
contact lenses and continue rinsing. Contaminated work clothing
should not be allowed out of the workplace. Wash contaminated
clothing before reuse. Dispose of in accordance with local, state,
and federal regulations. For more information call Product Safety:
800 507-8899 or see the SDS at usg.com
KEEP OUT OF REACH OF CHILDREN.
TRADEMARKS
The trademarks USG, DUROCK, EDGEGUARD, IT’S YOUR WORLD.
BUILD IT., the USG logo, the design elements and colors, and related
marks are trademarks of USG Corporation or its a liates.
NOTE
The information in this document is subject to change without
notice. USG Corp. assumes no responsibility for any errors that may
inadvertently appear in this document. Consult your USG Company
sales o ce or representative for information. Products described
here may not be available in all geographic markets.
NOTICE
We shall not be liable for incidental and consequential damages,
directly or indirectly sustained, nor for any loss caused by
application of these goods not in accordance with current printed
instructions or for other than the intended use. Our liability is
expressly limited to replacement of defective goods. Any claim shall
be deemed waived unless made in writing to us within thirty (30)
days from date it was or reasonably should have been discovered.
SAFETY FIRST!
Follow good safety/industrial hygiene practices during installation.
Wear appropriate personal protective equipment. Read SDS and
literature before specifi cation and installation.
CB237EG-USA-ENG/11-17
© 2017 USG Corporation and/or its affiliates.
All rights reserved. Printed in U.S.A.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
DUROCK Brand 170579 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
RSI RSI-IFS-BN-12 Operating instructions
-
DUROCK 170573 Installation guide
-
Premier Copper Products T4DBD_PKG4 Installation guide
-
Clearly Secure 2832SICDV Installation guide
-
Primo Tools TLSS120 Specification
-
Giorbello G6144-SMPL Installation guide
-
Crossco AD160-5 Installation guide
-
ABOLOS HMDMNT3DX-CA User manual
-
Johns Manville 90016810 Installation guide
-
USG Durock Brand 170120 Installation guide
