WALL MOUNT INSTALLATION INSTRUCTIONS
To adjust the height of light: IMPORTANT: This step must be
completed before trimming the wires and mounting the xture to the
wall.
Loosen wing nut. Carefully pull cord/xture wires up or down to
achieve desired height. Once desired height is achieved, tighten
wing nut to secure cord.
CAUTION: Cord and wires must be trimmed for the wall mount
installation ONLY. DO NOT cut cord and wires if this xture will be
mounted to the ceiling.
1) Cut cord with wires 7 inches past the canopy. With wire
strippers, remove 2 inches from end of each wire jacket.
Then strip 1/2 inch from end of each colored wire from wire
jacket.
2) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the xture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the xture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
3) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
4) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of xture.
5) Grounding instructions: (See Illus. A or B).
A) On xtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On xtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If xture is provided with ground wire. Connect xture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
6) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
7) Push xture to wall, carefully passing mounting screws
through holes in canopy.
8) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure xture to wall.
Date Issued: 11/6/17 IS-43589-US
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CEILING MOUNT INSTALLATION INSTRUCTIONS
To adjust the height of light: IMPORTANT: This step must be
completed before trimming the wires and mounting the xture to the
wall.
Loosen wing nut. Carefully pull cord/xture wires up or down to
achieve desired height. Once desired height is achieved, tighten
wing nut to secure cord.
1) From inside canopy, remove henxut and lockwasher from
threaded pipe.
2) Remove canopy from L-shaped arm. Pull cord/xture wires
through hole in canopy.
3) Unscrew L-shaped arm from coupling on top of bar. Carefully
pull cord/xture wires through arm.
4) Pass xture xture wire from coupling on top of bar through
stem. Thread end of stem into coupling. NOTE: Thread
locking compound must be applied to all stem threads as
noted with symbol (3) to prevent accidental rotation of
xture during cleaning, relamping, etc.
5) Pass xture wire through remaining stems and screw stems
together.
6) Thread one small threaded pipe into end of each small loop.
7) Pass xture wire through rst loop. Thread rst loop onto
end of last stem.
8) Pass xture wire through second loop and through hole in
canopy.
9) Pass threaded pipe at end of second loop through hole in
canopy.
10) Pass xture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
11) Pass xture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
12) Attach chain link to small loop at end of stem and to loop on
canopy.
13) Follow steps 2-8 in Wall Mount Installation Instructions.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
MOUNTING STRAP
ABRAZADERA DE
MONTAJE
CANOPY
ESCUDETE
KNURL KNOB
PERILLA
ESTRADA
SMALL LOOP
ARGOLLA
PEQUEÑA
CHAIN LINK
ESLABÓN DE
CADENA
4
STEM
VASTAGO
WING NUT
TUERCA DE
MARIPOSA
CORD
CORDÓN
4
COUPLING
ACOPLAMIENTO
WALL MOUNT INSTALLATION
INSTALACIÓN DE MONTAJE EN LA PARED
CEILING MOUNT INSTALLATION
INSTALACIÓN DE MONTAJE EN
EL TECHO
L-SHAPED ARM
BRAZO EN FORMA DE ‘L’
Page is loading ...
WALL MOUNT INSTALLATION INSTRUCTIONS
To adjust the height of light: IMPORTANT: This step must be
completed before trimming the wires and mounting the xture to the
wall.
Loosen wing nut. Carefully pull cord/xture wires up or down to
achieve desired height. Once desired height is achieved, tighten
wing nut to secure cord.
CAUTION: Cord and wires must be trimmed for the wall mount
installation ONLY. DO NOT cut cord and wires if this xture will be
mounted to the ceiling.
1) Cut cord with wires 7 inches past the canopy. With wire
strippers, remove 2 inches from end of each wire jacket.
Then strip 1/2 inch from end of each colored wire from wire
jacket.
2) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the xture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the xture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
3) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
4) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of xture.
5) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
6) Push xture to ceiling, carefully passing mounting screws
through holes in canopy.
7) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure xture to ceiling.
CEILING MOUNT INSTALLATION INSTRUCTIONS
To adjust the height of light: IMPORTANT: This step must be
completed before trimming the wires and mounting the xture to the
wall.
Loosen wing nut. Carefully pull cord/xture wires up or down to
achieve desired height. Once desired height is achieved, tighten
wing nut to secure cord.
1) From inside canopy, remove henxut and lockwasher from
threaded pipe.
2) Remove canopy from L-shaped arm. Pull cord/xture wires
through hole in canopy.
3) Unscrew L-shaped arm from coupling on top of bar. Carefully
pull cord/xture wires through arm.
4) Pass xture xture wire from coupling on top of bar through
stem. Thread end of stem into coupling. NOTE: Thread
locking compound must be applied to all stem threads as
noted with symbol (3) to prevent accidental rotation of
xture during cleaning, relamping, etc.
5) Pass xture wire through remaining stems and screw stems
together.
6) Thread one small threaded pipe into end of each small loop.
7) Pass xture wire through rst loop. Thread rst loop onto
end of last stem.
8) Pass xture wire through second loop and through hole in
canopy.
9) Pass threaded pipe at end of second loop through hole in
canopy.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 11/06/17 IS-43589-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
MOUNTING STRAP
PATTE DE FIXATION
CANOPY
CACHE
KNURL KNOB
BOUTON MOLETÉ
SMALL LOOP
PETITE BOUCLE
STEM
TIGE
CHAIN LINK
MAILLON DE LA
CHAÎNE
3
4
COUPLING
ACCOUPLEMENT
SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-
LATIONS.
VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-
DUCTIONS EN FRANÇAIS.
10) Pass xture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
11) Pass xture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
12) Attach chain link to small loop at end of stem and to loop on
canopy.
13) Follow steps 2-7 in Wall Mount Installation Instructions.
WING NUT
ÉCROU À AILETTES
CORD
CORDON
WALL MOUNT INSTALLATION
INSTALLATION MURALE
CEILING MOUNT INSTALLATION
INSTALLATION AU PLAFOND
L-SHAPED ARM
BRAS EN FORME DE L
MOUNTING STRAP
PATTE DE FIXATION
CANOPY
CACHE
WING NUT
ÉCROU À AILETTES
CORD
CORDON
Page is loading ...
/
