A
A
A
O
O
O
E
C
End Cap
End Cap
O
O
E
With the Powers Hydropanel II Modular Shrouding System
you can specify standardized shrouding panels to cover all
shower room piping, without the expense of customized
components. By using the Powers specification charts,
you coordinate different sizes of the five panel types,
based on the dimensions of your shower room. The modu-
lar components promote easy installation and fast delivery.
Hydropanel II Modular Shrouding is stainless steel and uti-
lizes vandal resistant fasteners with standardized heads.
TECHNICAL INSTRUCTIONS
HYDROPANEL
TM
II
MODULAR SHROUDING SYSTEM
Form TI 450SH v3
DESCRIPTION
1. The distance between the centerlines of two vertical
sections (vertical piping run or Hydropanel II unit)
should be at least 18
" [460 mm]. Recommended stan-
dard distance is 36
" [915 mm].
2. The distance between the centerline of any vertical sec-
tion (vertical piping run or Hydropanel II unit) and a wall
should be at least 20
" [510 mm].
3. The distance between the top of a Hydropanel II unit
and the ceiling should be at least 9-1/2
" [940 mm].
4. 16
" [405 mm] Horizontal Adapters are used at the end of
a piping run.
5. Each Corner Adapter, 13
", 16", 18", 23", or 28" Overlay,
or Extension Kit includes a stainless steel panel, and (2)
mounting brackets with (2) screws. Each Horizontal
Adapter or 8
" Overlay Kit includes a stainless steel
panel and (4) mounting brackets with (4) screws (wall
mounting screws not provided).
6. The 16
" Horizontal Adapter Kit includes an End Cap Kit.
The End Cap Kit comes complete with (1) chrome plat-
ed end cap and (3) mounting screws.
7. Position the brackets on the wall according to the
dimensions of the individual piece of shrouding (refer to
pages 3 and 4 for drawings). You can also hold the
piece of shrouding to the wall as a template to deter-
mine bracket position.
8. All brackets mount with the 1/4
" hole to the wall, facing
in (refer to Figure 1).
9. The 3/4
" wide oval mounting holes on the shrouding
allow up to 1/2
" error in shroud/bracket mounting.
GUIDELINES
To install Hydropanel II Modular Shrouding, follow the
room layout drawing from Form #PS450SH. The product
specification diagram not only describes the positions of
the different types and sizes of shrouding, but also pro-
vides the following information:
• Room dimensions and showerhead height.
• The number of shower units in the plan.
• The beginning, end and changes in direction of the
supply piping.
• The walls on which to mount the corner shrouding.
On each shrouding component is a letter-number code
that represents panel type and length (as listed below).
Shrouding components install in the following general
order, in thefollowing situations:
1. Horizontal Adapters (A16, A24, A48)
a. Piping bends/ends-of-run.
b. Hydropanel II units.
2. Corner Adapters - going into the corner (C10)
Fit the Corner Adapter onto the appropriate wall.
3. Extensions (E6, E24)
a. Into the cutout on top of the Horizontal Adapters.
b.Vertically onto the top of a Hydropanel II unit.
c. Special cases: on an open end of an Adapter to
extend its reach.
4. Overlays (O8, O13, O18, O23, O28)
a. Between two Horizontal Adapters.
b. Between a Corner Adapter and Horizontal Adapter
on the same wall.
c. Between a Corner Adapter and Horizontal Adapter
on adjacent walls (90° angle).
d. Between the ceiling and an Extension.
e. Special cases: between an Extension and an
Adapter.
5. End Caps
Fit End Caps onto the open ends of Horizontal
Adapters or atop an open Hydropanel II unit.
GETTING READY
5"
1/4" DIA..
10-32 UNF-2B THD.
WALL
Figure 1. Mounting Brackets and Shrouding
TI 450SH v3 Page 2
Use your Specification diagram from Form #PS450SH and
Figure 4 as keys to shrouding component positioning.
1. Mount all Hydropanel II shower units and End Caps
For complete shower installation instructions, refer to
the Technical Instructions for each Hydropanel II show-
er unit (Form #TI450-410, -420, -900, or -M)
2. Draw level lines for the horizontal shrouding.
(Figure 2) Brackets for the horizontal shrouding will
mount on “upper” and “lower” level lines. Draw a hori-
zontal line 8-9/16
" above showerhead height center-
line. Then draw a horizontal line 5
" below this upper
level line. Extend both lines around the shower room
for all horizontal shrouding.
3. Draw plumb lines for the vertical shrouding.
(Figure 3) Brackets for the vertical shrouding will mount
along “left” and “right” plumb lines. Strike a mid-line on
the wall at the shower unit/vertical section centerline
(halfway between the hot and cold supply water pipes).
Draw one vertical line 2-1/2
" to the left and one 2-1/2"
to the right of the mid-line. Extend both plumb lines for
all vertical piping.
4. Mount Horizontal Adapters (A).
Horizontal Adapters fit over piping bends and
Hydropanel II units, and use two upper and two lower
mounting brackets. The horizontal space between the
two sets of mounting brackets depends on component
length. Refer to the dimensional drawing, or hold
Adapter in position to mark bracket positions. Attach
brackets to the wall, mount Adapter and secure to the
brackets with 10-32 screws (included).
5. Mount Corner Adapters (C).
Consult the Specification diagram from Form
#PS450SH to determine on which adjoining wall to
mount the Corner Adapter(s). Proper installation of all
shrouding pieces depends upon correct positioning of
the Corner Adapters. Brackets for corner shrouding
mount 5
" out from the room corner (see dimensional
drawing). Attach brackets to the wall, mount Adapter
and secure to the brackets with 10-32 screws (includ-
ed).
6. Mount Vertical Extensions (E).
(Figure 4, next page) Vertical Extensions fit into the cut-
out on a Horizontal Adapter or onto the top of a
Hydropanel II unit. Use the Extension as a template, or
determine the bracket position (one left and one right)
with the dimensional drawing. Attach brackets to the
wall, then mount Adapter and secure to the brackets
with 10-32 screws (included).
7. Mount Horizontal Extensions (not shown)
Before mounting a Horizontal Extension to extend the
reach of an Adapter, fit and secure an End Cap into the
appropriate Adapter end. The End Cap functions as a
gasket between these two pieces that cannot overlap.
Then use the Horizontal Extension as a template to
mark the positions of the upper and lower brackets (1
each). Attach brackets to the wall, mount Adapter and
secure to the brackets with 10-32 screws (included).
8. Mount all Overlay Shrouding (O).
The Hydropanel II Modular Shrouding system specifies
Overlay shrouding that overlaps Adapters and
Extension about 1
" on each side (but can be more). To
determine the position of the mounting brackets on the
wall, either a) measure the distance between the pieces
it overlaps (Extensions, ceiling, wall, Adapters, etc.) and
divide this distance in half; or b) place the Overlay in
position and mark the locations of the bracket mounting
holes. Attach brackets to the wall, mount Adapter and
secure to the brackets with 10-32 screws (included).
9. Mount end-of-run End Caps.
Each 16
" Horizontal Adapter Kit includes an end cap.
Position End Cap on the open end of the Adapter and
attach with the 3 screws provided (no drilling or mount-
ing brackets necessary).
INSTALLATION
77"
8-9/16"5"
Level Line for upper brackets
Level Line for lower brackets
2-1/2"
Plumb Line for
left brackets
Plumb Line for
right brackets
2-1/2"
Mid Line
Supply piping
(max. 6-5/16")
Figure 2. Horizontal Level Lines
Figure 3. Vertical Plumb Lines
TI 450SH v3 Page 3
DIMENSIONS
A
A
A
O
O
O
E
C
End Cap
End Cap
O
O
E
7.210"
1/4" W X 3/4" L ( 2 EACH SIDE )
.240"
1-1/8"
7.000"
7.000"
2.400"
1/4" W X 3/4" L (ONE EACH SIDE)
2.000"
6.000"
10.000"
5.000"
1-1/8"
2.400"
7.000"
1/4 W X 3/4 L
(ONE EACH SIDE)
1 1/8"
4"
7.096"
2.448"
8"
1-1/8"
3/4"
1/4" W X 3/4" L
(2 EACH SIDE)
Figure 4. Room Layout
Horizontal Adapters
AB Product No.
16” 4.5” 450 4040
24” 6” 450 4041
48” 12” 450 4042
Extensions
AB Product No.
6” .75” 450 4050
24” 10” 450 4051
Corner Adapters
Length Product No.
10” 450 4049
Overlay
Length Product No.
8” Overlay 450 4043
8
7
9
4
8
4
8
5
8
4
9
1
8
7
1
TI 450SH v3 Page 4
7.096"
2.448"
1-1/8"
1/4 W X 3/4 L (ONE EACH SIDE)
3/8"
Overlays
AB Product No.
13” 6.5” 450 4044
16” 8” 450-4045
18” 9” 450 4046
23” 11.5” 450 4047
28” 14” 450-4048
10-32 UNF-2B THD.
1-1/8"
1/2"
1"
1"
1-1/2"
1/4" DIA.
1/2"
.375"
7.080"
6.960"
5/8"
2.370"
Accessories
Item Product No.
Bracket 450 334
Accessories
Item Product No.
End Cap 450 4011
Qty Description Size (Metric) Order #
Horizontal Adapter Kit 16” 405mm 450 4040
Horizontal Adapter Kit 24” 610mm 450 4041
Horizontal Adapter Kit 48” 1220mm 450 4042
Overlay Shroud Kit 8” 205mm 450 4043
Overlay Shroud Kit 13” 330mm 450 4044
Overlay Shroud Kit 16” 405mm 450 4045
Overlay Shroud Kit 18” 455mm 450 4046
Overlay Shroud Kit 23” 585mm 450 4047
Overlay Shroud Kit 28” 710mm 450 4048
Corner Adapter Kit 10” 255mm 450 4049
Qty Description Size (Metric) Order #
Extension Shroud Kit 6” 150mm 450 4050
Extension Shroud Kit 24” 610mm 450 4051
End Cap Kit 450 4011
Bracket Kit 450 334
Each Hydropanel II Modular Shrouding Corner Adapter, 13”, 16”, 18”, 23”, or 28” Overlay, or
Extension Kit comes complete with stainless steel panel, and (2) mounting brackets with (2) screws.
Each Horizontal Adapter or 8” Overlay Kit comes complete with stainless steel panel and (4) mounting
brackets with (4) screws.
The 16” Horizontal Adapter Kit also includes an End Cap kit. The End Cap Kit comes complete with (1)
chrome plated end cap and (3) mounting screws.
ORDERING
CALIFORNIA PROPOSITION 65 WARNING
WARNING: This product contains chemicals
known to the State of California to cause cancer
and birth defects or other reproductive harm.
(California law requires this warning to be given to
customers in the State of California.)
For more information: www.wattsind.com/prop65
© 2006 Powers
USA: Phone: 1.800.669.5430 • Fax 1.847. 229.0526 • www.powerscontrols.com
Canada: Phone: 1.888.208.8927 • Fax 1. 888. 882 .1979 • www.powerscontrols.ca
Form TI 450SH v3 0333 EDP# 6508995 Printed in U.S.A.
-
1
-
2
-
3
-
4
Powers HydroPanel II 450 Infrared Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Powers HydroPanel II 450 Meter Installation guide
-
Powers HydroPanel II 450-e420 Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Enviro 1200 User manual
-
ABB ACS880-37LC User manual
-
-
-
Hearth and Home Technologies Indoor Fireplace 4055-187 User manual
-
Lincoln Electric IM645-A User manual
-
NYMAS M83945 Operating instructions
-
Quadra-Fire CB1200MI-MBK User manual
-
-
Quadrafire 1200-I Pellet Insert Install Manual
