DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK User manual

Brand
DTS
Model
03.P16.02.01.LED PAR16 LED MR16 BLACK
Type
User manual

This manual is also suitable for

Technical Datasheet
GB
Made in Italy
PAR16 LED
User’s Manual Rel 1.1
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
03.P16.02.02.LED
PAR16 LED MR16 LUX
03.P16.02.01.LED
PAR16 LED MR16 BLACK
Page is loading ...
DESCRIPTION
Protection
Ip20 protection level against the penetration of solids
and liquids
Construction
PAR16 LED is made on aluminium
Standard accessories
MR16 LED lens holder
Weight
0,2 kg
The PAR16 LED is a projector for MR16 LED lamp, with classic shape in 2 sections, square
filterframe, and polished finishing.
The projector is available also with black finishing. (03.P16.02.01.LED)
The projector is provided with a LED lens holder (no MR16 LED lamp unit included).
D.T.S. uses top-quality 99/5 aluminium with a 20/10 thickness for its can bodies, offering greater
strength and incredible resistance to knocks and heat, together with a superior polish.
The edge is not sharp and is therefore safer; it is stronger and conveys extra strength to the
body; it is better finished, making the PAR16 LED more elegant.
The PAR16 LED is fitted with an internal safety cable between rear and front.
The internal plate + clutch system of the PAR16 LED is preferable to other systems that corrode
aluminium or don’t offer a good grip. This ensures safer operation because it permits 0° ÷ 90°
rotation (as requested by international safety standards) and the par can cannot take up
positions that are hazardous for the inflammable surfaces above the par can itself.
Unlike ordinary par cans, the gelatine bearing hooks are spoked to better adhere to the body,
thereby ensuring greater strength and indeformability.
02M00425.01
3
PAR16 LED
IMPORTANT SAFETY INFORMATION
Fire prevention:
Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm
Safety:
The external surface of the unit may exceed 50°C, never handle the unit until at least 5 minutes
have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C and should not be lower than -10°C.
The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the
main fixing point.
4
1) BRACKET
2) FIXING BRACKET
KNOB
3) REAR SIDE
4) FRONT SIDE
5) LED LENS HOLDER
6) REAR SIDE FIXING
KNOB
6
PAR16 LED
MR16 LED LAMP INSERTING PROCEDURE
5
Place a drop of silicone or other synthetic glue in the 3 holes to fix the LED module to the
dedicated D.T.S. lenses. Never touch the LEDs with hands
Silicone or synthetic glue
Place the MR16 LED unit into PAR16 LED by passing from the front side of the unit.
Fix the MR16 LED unit by using the dedicated LED lens holder
PAR16 LED
Page is loading ...
Page is loading ...
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.
MADE IN ITALY
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 [email protected] www.dts-lighting.it
8
ISO 9001:2000
D.T.S quality system
Is certified to the
ISO 9001:2000 standard
D.T.S. Products are designed
And manufactured at the D.T.S
Plants in Italy
The Lighting Company
*0517I129*
0517I129
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK User manual

Brand
DTS
Model
03.P16.02.01.LED PAR16 LED MR16 BLACK
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents