Benchmark Scientific BV1000-COMBO Installation guide

BV1000-COMBO
Benchmark Scientific
Brand
Benchmark Scientific
Model
BV1000-COMBO
Type
Installation guide

This manual is also suitable for

Benchmark Scientific BV1000-COMBO is a versatile laboratory vortex mixer suitable for various mixing applications, featuring variable speed control, interchangeable heads, and a compact design. With its adjustable speed ranging from 200 to 3200 RPM, it offers precise control over mixing intensity. The unit comes with three interchangeable heads: a rubber cup head for general mixing, a 3" round flat head with a sponge disc for larger tubes, and a 1.5 ml microtube head for microcentrifuge tubes. The compact design allows for easy placement on the laboratory bench, saving valuable workspace.

Benchmark Scientific BV1000-COMBO is a versatile laboratory vortex mixer suitable for various mixing applications, featuring variable speed control, interchangeable heads, and a compact design. With its adjustable speed ranging from 200 to 3200 RPM, it offers precise control over mixing intensity. The unit comes with three interchangeable heads: a rubber cup head for general mixing, a 3" round flat head with a sponge disc for larger tubes, and a 1.5 ml microtube head for microcentrifuge tubes. The compact design allows for easy placement on the laboratory bench, saving valuable workspace.

Installation of accessory heads Installation of accessory heads
on model BenchMixer Vortexers on model BenchMixer Vortexers
1. Grasp the Benchmixer™ with one hand and 1. Grasp the Benchmixer™ with one hand and
gently rotate the rubber cup head counter gently rotate the rubber cup head counter
clock wise to loosen and remove it. clock wise to loosen and remove it.
2. Observe the bottom of the plastic mount on 2. Observe the bottom of the plastic mount on
the accessory head and align the slot on the the accessory head and align the slot on the
on the bottom with the two flat areas on the on the bottom with the two flat areas on the
mixer’s drive shaft and gently press down. mixer’s drive shaft and gently press down.
The plastic mount should drop down and sit The plastic mount should drop down and sit
firmly on the mixer’s shaft. firmly on the mixer’s shaft.
3. Insert the screw in the center hole and 3. Insert the screw in the center hole and
gently tighten with a Phillips screw driver. gently tighten with a Phillips screw driver.
4. On the 3” round FLAT head, remove 4. On the 3” round FLAT head, remove
the protective paper from each of the tape the protective paper from each of the tape
strips to expose the tacky surface. Then strips to expose the tacky surface. Then
press the smooth side of the round sponge press the smooth side of the round sponge
disc on to the plastic mount so that the disc on to the plastic mount so that the
sponge firmly sticks to the plastic mount. sponge firmly sticks to the plastic mount.
5. Test the newly installed head at slow 5. Test the newly installed head at slow
speed before using it to mix tubes. speed before using it to mix tubes.
Installation of accessory heads Installation of accessory heads
on model BenchMixer Vortexers on model BenchMixer Vortexers
1. Grasp the Benchmixer™ with one hand and 1. Grasp the Benchmixer™ with one hand and
gently rotate the rubber cup head counter gently rotate the rubber cup head counter
clock wise to loosen and remove it. clock wise to loosen and remove it.
2. Observe the bottom of the plastic mount on 2. Observe the bottom of the plastic mount on
the accessory head and align the slot on the the accessory head and align the slot on the
on the bottom with the two flat areas on the on the bottom with the two flat areas on the
mixer’s drive shaft and gently press down. mixer’s drive shaft and gently press down.
The plastic mount should drop down and sit The plastic mount should drop down and sit
firmly on the mixer’s shaft. firmly on the mixer’s shaft.
3. Insert the screw in the center hole and 3. Insert the screw in the center hole and
gently tighten with a Phillips screw driver. gently tighten with a Phillips screw driver.
4. On the 3” round FLAT head, remove 4. On the 3” round FLAT head, remove
the protective paper from each of the tape the protective paper from each of the tape
strips to expose the tacky surface. Then strips to expose the tacky surface. Then
press the smooth side of the round sponge press the smooth side of the round sponge
disc on to the plastic mount so that the disc on to the plastic mount so that the
sponge firmly sticks to the plastic mount. sponge firmly sticks to the plastic mount.
5. Test the newly installed head at slow 5. Test the newly installed head at slow
speed before using it to mix tubes. speed before using it to mix tubes.
  • Page 1 1

Benchmark Scientific BV1000-COMBO Installation guide

BV1000-COMBO
Benchmark Scientific
Brand
Benchmark Scientific
Model
BV1000-COMBO
Type
Installation guide
This manual is also suitable for

Benchmark Scientific BV1000-COMBO is a versatile laboratory vortex mixer suitable for various mixing applications, featuring variable speed control, interchangeable heads, and a compact design. With its adjustable speed ranging from 200 to 3200 RPM, it offers precise control over mixing intensity. The unit comes with three interchangeable heads: a rubber cup head for general mixing, a 3" round flat head with a sponge disc for larger tubes, and a 1.5 ml microtube head for microcentrifuge tubes. The compact design allows for easy placement on the laboratory bench, saving valuable workspace.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents