2. Benchmark Scientific
  3. BV1000-FLAT
BV1000-FLAT

Benchmark Scientific BV1000-FLAT, BV1000-COMBO Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Benchmark Scientific BV1000-FLAT Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I install accessory heads on the BenchMixer Vortexers?
    How do I remove the accessory heads from the BenchMixer Vortexers?
    How do I clean and maintain the BenchMixer Vortexers?
    What are the different accessory heads available for the BenchMixer Vortexers?
    What is the maximum speed of the BenchMixer Vortexers?
Installation of accessory heads Installation of accessory heads
on model BenchMixer Vortexers on model BenchMixer Vortexers
1. Grasp the Benchmixer™ with one hand and 1. Grasp the Benchmixer™ with one hand and
gently rotate the rubber cup head counter gently rotate the rubber cup head counter
clock wise to loosen and remove it. clock wise to loosen and remove it.
2. Observe the bottom of the plastic mount on 2. Observe the bottom of the plastic mount on
the accessory head and align the slot on the the accessory head and align the slot on the
on the bottom with the two flat areas on the on the bottom with the two flat areas on the
mixer’s drive shaft and gently press down. mixer’s drive shaft and gently press down.
The plastic mount should drop down and sit The plastic mount should drop down and sit
firmly on the mixer’s shaft. firmly on the mixer’s shaft.
3. Insert the screw in the center hole and 3. Insert the screw in the center hole and
gently tighten with a Phillips screw driver. gently tighten with a Phillips screw driver.
4. On the 3” round FLAT head, remove 4. On the 3” round FLAT head, remove
the protective paper from each of the tape the protective paper from each of the tape
strips to expose the tacky surface. Then strips to expose the tacky surface. Then
press the smooth side of the round sponge press the smooth side of the round sponge
disc on to the plastic mount so that the disc on to the plastic mount so that the
sponge firmly sticks to the plastic mount. sponge firmly sticks to the plastic mount.
5. Test the newly installed head at slow 5. Test the newly installed head at slow
speed before using it to mix tubes. speed before using it to mix tubes.
Installation of accessory heads Installation of accessory heads
on model BenchMixer Vortexers on model BenchMixer Vortexers
1. Grasp the Benchmixer™ with one hand and 1. Grasp the Benchmixer™ with one hand and
gently rotate the rubber cup head counter gently rotate the rubber cup head counter
clock wise to loosen and remove it. clock wise to loosen and remove it.
2. Observe the bottom of the plastic mount on 2. Observe the bottom of the plastic mount on
the accessory head and align the slot on the the accessory head and align the slot on the
on the bottom with the two flat areas on the on the bottom with the two flat areas on the
mixer’s drive shaft and gently press down. mixer’s drive shaft and gently press down.
The plastic mount should drop down and sit The plastic mount should drop down and sit
firmly on the mixer’s shaft. firmly on the mixer’s shaft.
3. Insert the screw in the center hole and 3. Insert the screw in the center hole and
gently tighten with a Phillips screw driver. gently tighten with a Phillips screw driver.
4. On the 3” round FLAT head, remove 4. On the 3” round FLAT head, remove
the protective paper from each of the tape the protective paper from each of the tape
strips to expose the tacky surface. Then strips to expose the tacky surface. Then
press the smooth side of the round sponge press the smooth side of the round sponge
disc on to the plastic mount so that the disc on to the plastic mount so that the
sponge firmly sticks to the plastic mount. sponge firmly sticks to the plastic mount.
5. Test the newly installed head at slow 5. Test the newly installed head at slow
speed before using it to mix tubes. speed before using it to mix tubes.
/