KidKraft Timber Trail Wooden Outdoor Playhouse Assembly Instruction

INSTALLATION AND OPERATING INSTRUCTIONS

TIMBER TRAIL PLAYHOUSE FSC - P280099

Rev 08/31/2020

Table of Contents

Warnings and Safe Play Instructions ........pg. 2

Instructions for Proper Maintenance ........pg. 2

Keys to Assembly Success ...................pg. 3

About Our Wood – Limited Warranty ......pg. 4-5

Battery Instruction and Warranty ...........pg. 6

Part ID .....................................pg. 7

Step-By-Step Instructions ................. pg. 15

Installation of ID/Warning Plaque ......... pg. 69

To reduce the risk of serious injury or death,

you must read and follow these instrucons.

Keep and refer to these instrucons oen and

give them to any future owner of this play set.

Manufacturer contact informaon provided below.

OBSTACLE FREE SAFETY ZONE - 19’ 9” x 17’ 9” (6.02 x 5.41m)

CAPACITY - 4 Users Maximum, Ages 2 to 10. Weight Limit 110 lbs. (49.9 kg) per bench.

RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches,

nurseries, day cares or parks.

WARNING. Only for domesc use.

WARNING

2-4 Hrs

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

10 - 12 Hrs

FOR FORT & SWING

1.5 - 2 Hrs

FOR OUTDOOR FAMILY

DOMESTIC USE ONLY

9400099

Cedar Summit by KidKraft

4630 Olin Road

Dallas, TX 75244, United States

[email protected]

Online Parts Replacement: parts.kidkraft.com

To warranty your product: kidkraft.com/warranty/

Customer Service: 1(800) 933-0771 or (972) 385-0100

KidKraft Netherlands BV

Olympisch Stadion 8

1076 DE Amsterdam, The Netherlands

Europe Customer Service: +31 (0)20 305 8620

europecustomerservice@kidkraft.com

EU Online Parts Replacement: parts.kidkraft.eu

5.41m

17’ 9”

1.41m

4’ 7.6”

2.02m

6’ 7.5”

6.02m

19’ 9”

2

Warnings and Safe Play Instructions

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have

occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards.

Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children

using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they

understand and follow them. Remember on-site adult supervision is required for children of all ages.

Dress children with well fitting and full foot enclosing

footwear.

Check for splintered, broken or cracked wood; missing,

loose, or sharp edged hardware. Replace, tighten and or

sand smooth as required prior to playing.

Replace defective parts in accordance with manufacturer’s

instructions.

Do not allow children to wear open toe or heel footwear

like sandals, flip–flops or clogs.

Do not permit climbing on equipment when it is wet.

Do not permit rough play or use of equipment in a manner

for which it was not intended. Standing or climbing on or

jumping from the roof.

WARNING – Safe Play Instructions

CHOKING HAZARD/SHARP EDGES & POINTS

Adult assembly required. This product contains small

parts and parts with sharp edges and points. Keep parts

away from children until fully assembled.

STRANGULATION HAZARD

• NEVER allow children to play with ropes,

clotheslines, pet leashes, cables, chains or cord-like

items when using this playhouse or to attach these

items to the playhouse.

• NEVER allow children to wear loose fitting clothing,

ponchos, hoods, scarves, capes, necklaces, items with

draw-strings, cords or ties when using this playhouse.

• NEVER allow children to wear bike or sport helmets

when using this playhouse.

Failure to prohibit these items, even helmets with chin

straps, increases the risk of serious injury and death to

children from entanglement and strangulation.

TIP OVER HAZARD

Choose a level location for the equipment. This can

r

educe the likelihood of the playhouse tipping over

and loose-fill surfacing materials washing away during

heavy rains.

DO NOT allow children to play on the playhouse until

the assembly is complete.

PLACEMENT

Place the toy on a level surface at least 2m from any

structure or obstruction such as fences, garages, house,

overhanging branches, laundry or electrical wires.

WARNING

HARDWARE:

Check metal parts for rust. If found,

sand and repaint using a non-lead paint

complying with 16 CFR 1303.

Inspect and tighten all hardware. On

wood assemblies DO NOT OVER-

TIGHTEN as to cause crushing and

splintering of wood.

Check for sharp edges or protruding screw threads, add

washers if required.

WOOD PARTS:

Check all wood members for deterioration, structural

damage and splintering. Sand down splinters and replace

deteriorated wood members. As with all wood, some

checking and small cracks in grain is normal.

Applying a water repellent or stain (water-based) on a yearly

basis is important maintenance to maintain maximum life

and performance of the product.

Instructions for Proper Maintenance

Your Play System is designed and constructed of quality materials with your child’s safety in mind. As with

all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your

Playhouse, it is important that you, the owner, properly maintain it.

Check the following at the beginning of the play season:

Check twice a month during play season:

HARDWARE:

Inspect for tightness. Must be firmly against, but not crushing the wood.

DO NOT OVER-TIGHTEN. This will cause splintering of wood.

Check for sharp edges or protruding

screw threads. Add washers if required.

If you dispose of your playhouse: Please disassemble and dispose of your unit so that it does not create any unreasonable

hazards at the time it is discarded. Be sure to follow your local waste ordinances.

3

Part Identification Key

On each page, you will find the parts

and quantities required to complete the

assembly step illustrated on that page.

Here is a sample.

Key Number: The first two digits

represent the step number. The third

digit represents the piece. Note that

if the part is used in multiple steps

then the number only reflects the

first step it is used in.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

Proper Hardware Assembly

Lag screws require drilling pilot holes to

avoid splitting wood. Only a flat washer

is required. For ease of installation

liquid soap can be used

on all lag-type screws.

For bolts, tap T-Nut into hole with

hammer. Insert the hex bolt through

lock washer first then flat washer then

hole. Because the assemblies need to

be squared do not completely tighten

until instructed. Pay close attention to

diameter of the bolts. 5/16” is slightly

larger than 1/4

”.

Note: Wafer head bolts with blue lock

tight or a bolt with a Ny-Lok nut do

NOT require a lock washer.

Once the assembly is tightened, watch for exposed

threads. If a thread protrudes from the T-Nut, remove

the bolt and add washers to eliminate this condition.

Extra washers have been provided for this purpose.

This identifies information that requires special

attention. Improper assembly could lead to an

unsafe or dangerous condition.

Where this is shown, 2 or 3

people are required to safely

complete the step. To avoid

injury or damage to the

assembly make sure to get

help!

Check that assembly is square

before tightening bolts.

Use a measuring tape to assure

proper location.

Check that set or assembly is properly level

before proceeding.

Pre-drill a pilot hole

before fastening screw

or lag to prevent

splitting of wood.

This indicates time to tighten bolts, but

not too tight! Do not crush the wood.

This may create splinters and cause

structural damage.

Use

Help

Use

Help

Measure

Distance

Square

Assembly

Use

Level

Pre-drill 1/8” & 3/16” Bit

Tighten

Bolts

CAUTION – Protrusion Hazard

Keys to Assembly Success

Tools Required

Quantity Key Number

Part Description,

Part Size

2X 012 Post 2 x 4 x 83”

No Yes

Lag Assembly

Bolt Assembly

Flat Washer

Lag Screw

Hex Bolt

Lock

Washer

Flat

Washer

Before mounting Lag

Screw, use factory drilled

holes as guides to drill 1/8”

pilot holes

T-Nut

(Hammer into place)

Do not crush wood!

If Bolt protrudes

beyond T-Nut

Use an extra

flat washer

4

About Our Wood

KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your

children’s use. Although we take great care in selecting the best quality lumber available, wood is still a

product of nature and susceptible to weathering which can change the appearance of your set.

What causes weathering? Does it affect the strength of my Play System?

One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood

at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out

of the wood, causing tension which can result in checking and or warping. You can expect the following

due to weathering. These changes will not affect the strength of the product:

1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking

than a board (1” x 4”) because the surface and interior moisture content will vary more widely than in

thinner wood.

2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often

happens from rapid wetting and drying of the wood.

3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey

over time.

How can I reduce the amount of weathering to my Play System?

At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount

of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down

the coating, so we recommend applying a water repellent or stain on a yearly basis (see your local stain

and paint supplier for a recommended product).

Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your

child. However if you are concerned that a part has experienced a severe weathering problem please call

our consumer relations department for further assistance.

Complete and mail registration card to receive important product notifications and assure prompt

warranty service.

5

KidKraft Limited Warranty

MISSING OR DAMAGED PARTS:

KidKraft will replace any parts within 90 days from date of purchase found to be missing from or

damaged in the original packaging. See Fig.1

Fig. 1 Product Age (All Parts) Consumer Pays

0-90 Days from date of purchase $0 for Part + Free Shipping

DEFECTS IN MATERIAL AND WORKMANSHIP:

KidKraft warrants that this product is free from defects in materials and workmanship for a period of one

(1) year from the original date of purchase (dated sales receipt and/or product registration is required).

This one (1) year warranty covers all parts including wood, hardware, and all accessories (Such as

swings, rides, and slides). See Fig. 2

Fig. 2 Product Age (All Part

s) Consumer Pays

91 Days to 1 Year $0 for Part + Free Shipping

WOOD ROT, DECAY, AND INSECT DAMAGE:

All wood carries a five (5) year warranty against rot, decay, and insect damage (dated sales receipt

and/or product registration is required). Refer to the schedule below for charges associated with

replacement of wood parts under this Limited Warranty. See Fig. 3

Fig. 3 Product Age (Wood Parts) Consumer Pays

0 Days to 1 Year $0 for Part + Free Shipping

After 1 Year to 5 Year $0 for Part + Shipping & Handling

Over 5 Years 100% for Part (if available) + Shipping & Handling

This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance

is required to ensure the integrity of this product. Failure by the owner to maintain the product according

to the maintenance requirements may void this warranty.

This Limited Warra

nty does NOT cover:

• Any inspection cost

• Labor and/or costs for replacement of any defective item(s), including but not limited to,

professional installer costs

• Incidental or consequential damages, including but not limited to, as a result of set relocation,

move and/or reinstall

• Cosmetic defects which do not affect performance or integrity of a part or the entire product

• Vandalism, improper use or installation, or acts of nature, including but not limited to, high win

ds,

fire, and flood

• Minor twisting, warping, checking, or any natural occurring properties of wood that do not affect

performance or integrity.

• Any KidKraft product purchased, including but not limited to, a non-approved retailer, auction

houses, second-hand, and as-is clearance items.

KidKraft products have been designed for safety and quality. Modifications made to the original product

may damage the structural integrity of the unit leading to failure and possible

injury. KidKraft cannot

assume any responsibility for the modified products. Furthermore, modifications void all warranties.

This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKraft

product be used in public settings such as schools, churches, playgrounds, parks, home and

professional day cares and the like. Such use may lead to product failure and potential injury. Public use

will void this warranty. KidKraft disclaims all other re

presentations and warranties of any kind, express or

implied.

6

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio /TV technician for help.

Note: Changes or modications not expressly approved by the manufacturer responsible for compliance

could void the user’s authority to operate the equipment.

Please retain the information on this pack for future reference.

- Batteries should always be installed and changed under adult supervision.

- Non-Rechargeable batteries are not to be recharged.

- Rechargeable batteries are only to be charged under adult supervision.

- Only batteries of the same equivalent type as recommended are to be used.

- Batteries are to be inserted with the correct polarity.

- Exhausted batteries are to be removed from the toy and disposed of properly.

- The supply terminals are not to be short circuited.

- Different types of batteries or new and used batteries are not to be mixed.

- DO NOT mix alkaline, standard (carbon-zinc) or rechargeable batteries.

- Be sure to insert new batteries with positive (+) side up.

- Rechargeable batteries are to be removed from the toy before being charged.

- EU Regulations require exhausted batteries to be separately collected so that they can be treated using

the best available recovery and recycling techniques. This will minimize the impact on the environment and

human health from soil and water contamination by any hazardous substances, decrease the resources

required to make new products and avoid using up landll space.

- Batteries or battery packs must be recycled or disposed of properly. When the batteries in this product

have reached the end of their useful life, they should not be disposed of with other household waste.

- Please do your part by keeping waste batteries out of the municipal waste stream!

Battery Instruction and Warranty

7

3pc.

-

241

-

31.8 x 50.8 x 108.8mm - Small Post FSC - Box 1 - 48088077

1 1/4" x 2" x 4-5/16"

1" x 1 3/4” x 28 9/16"

2pc.

-

181

-

25.4 x 44.4 x 725 mm - Low Window Support FSC - Box 1 - 48086437

1" x 2" x 12 1/2"

2pc.

-

133

-

25.4 x 50.8 x 317.1 mm - BBQ Support FSC - Box 1 - 48086937

1" x 2" x 9 15/16"

3pc.

-

132

-

25.4 x 50.8 x 252.6 mm - BBQ Upright FSC - Box 1 - 48087137

1" x 2" x 22 11/16"

2pc.

-

131

-

25.4 x 50.8 x 575.9 mm - BBQ Bottom FSC - Box 1 -

48087037

3pc.

-

134

-

15.9 x 101.6 x 575.9 mm - BBQ Top FSC - Box 1 - 48087237

5/8" x 4" x 22 11/16"

1pc.

-

171

-

25.4 x 50.8 x 575.9 mm - Door stop Bottom FSC - Box 1 - 48086537

1" x 2" x 22 11/16"

2pc.

-

122

-

19.1 x 63.5 x 553.4mm - Bay Window Wide FSC - Box 1 - 48087605

2pc.

-

121

-

19.1 x 50.8 x 548mm - Bay Window Narrow FSC - Box 1 - 48087505

11pc.

-

081

-

15.9 x 63.5 x 462.7 mm - Low Post FSC - Box 1 - 48087305

5/8" x 2 1/2" x 18 3/16"

3/4" x 2 1/2" x 21 13/16"

3/4" x 2 " x 21 9/16"

3pc.

-

123

-

25.4 x 50.8 x 272.1mm - Bay window Support FSC - Box 1 - 48087837

1" x 2" x 10 11/16"

2pc.

-

071

-

25.4 x 50.8 x 359.4 mm - Open Panel Beam FSC - Box 1 - 48085837

1" x 2" x 14 1/8"

1" x 2" x 10 3/4"

2pc.

-

072

-

25.4 x 50.8 x 272.7 mm - Roof support FSC - Box 1 - 48086137

10pc.

-

112

-

15.9 x 114.3 x 334 mm - Chair Top FSC - Box 1 - 48086837

5/8" x 4 1/2" x 13 1/8"

1pc.

-

102

-

25.4 x 50.8 x 334 mm - Chair Support FSC - Box 1 - 48086637

1" x 2" x 13 1/8"

2pc.

-

076

-

25.4 x 50.8 x 603.3 mm - Terrace top short FSC - Box 1 - 48085937

1" x 2" x 23 3/4"

8pc.

-

091

-

15.9 x 63.5 x 349.3 mm - Chair Post FSC - Box 1 - 48087905

5/8" x 2 1/2" x 13 3/4"

1pc.

-

051

-

23.8 x 63.5 x 127mm - Door Stop FSC - Box 1 - 48087437

15/16 x 2-1/2 x 5"

Part Identification (Reduced Part Size)

8

4pc.

-

141

-

25.4 x 69.9 x 727.4 mm - Windows support FSC - Box 1 - 48086337

1" x 2 3/4" x 28 5/8"

1pc.

-

075

-

25.4 x 50.8 x 1153.7 mm - Terrace top Long FSC - Box 1 - 48086037

1" x 2" x 45 7/16"

1pc.

-

073

-

25.4 x 50.8 x 1257.3 mm - Counter Beam FSC - Box 1 - 48085637

1" x 2" x 49 1/2"

2pc.

-

074

-

25.4 x 50.8 x 1166.4 mm - Main Beam FSC - Box 1 - 48085737

1" x 2" x 45 15/16"

2pc.

-

142

-

25.4 x 69.9 x 1168.4 mm - window bottom FSC - Box 1 - 48086237

1" x 2 3/4” x 46"

4pc.

-

272

-

15.9x76.2x1069.8 mm - Box Side Panel FSC - Box 1 - 48088237

5/8" x 3" x 42 1/8"

3pc.

-

271

-

15.9x76.2x1085.8 mm - Box Bottom FSC - Box 1 - 48088137

5/8" x 3" x 42 3/4"

2pc.

-

111

-

25.4 x 50.8 x 1166.4 mm - Chair Bottom FSC - Box 1 - 48086737

1" x 2" x 45 15/16"

2pc.

-

101

-

25.4 x 50.8 x 1204.5 mm - Counter Post Bottom FSC - Box 1 - 48087737

1" x 2" x 47 7/16"

2pc.

-

022

-

25.4 x 50.8 x 1204.5 mm - Side Tie FSC - Box 1 - 48085537

Part Identification (Reduced Part Size)

9

Part Identification (Reduced Part Size)

2pc.

-

191

Roof FSC

Box 1 - 478082477

28.6 x 654.1 x 900.4mm

1 1/8" x 25 3/4" x 35 29/64"

1pc.

-

193

Roof Panel RM FSC

Box 1 - 478082677

28.6 x 654.1 x 871.1mm

1 1/8" x 25 3/4" x 34 5/16"

28.6 x 766.7 x 1042.3mm

1 1/8" x 30 5/16" x41 1/16"

1pc.

-

202

- Roof Panel RF FSC

Box 1 - 478082877

28.6 x 766.7 x 1042.3mm

1 1/8" x 30 5/16" x 41 1/16"

1pc.

-

201

- Roof Panel LF FSC

Box 1 - 478082777

1pc.

-

192

Roof Panel LM FSC

Box 1 - 478082577

28.6 x 654.1 x 871.1mm

1 1/8" x 25 3/4" x 34 5/16"

10

1pc.

-

242

- Small Roof FSC

Box 1 - 478083177

43.7 x 172.4 x 1033.6mm

1 3/4"x 6 13/16" x 40 11/16"

Part Identification (Reduced Part Size)

1pc.

-

162

- Right Small Door FSC

Box 1 - 478083005

25.4 x 214.3 x 421.4mm

1" X 8 7/16" X 16 19/32"

1pc.

-

161

- Left Small Door FSC

Box 1 - 478082905

25.4 x 214.3 x 421.4mm

1" X 8 7/16" X 16 19/32"

25.6 x 376.6 x 961mm

1" x 14 13/16" x 37 13/16"

1pc.

-

041

- Door FSC

Box 1 - 478082027

11

Part Identification (Reduced Part Size)

1pc.

-

021

- Folded Panel

Assembly FSC

Box 1 - 478085537

478081437

478081637

478081537

478081737

478081837

478081937

1pc.

-

031

- Folded Terrace Panel

Assembly FSC

Box 1 - 478085637

478082137

478082337

478082237

If you need to order parts,

please order below part #

478081937 - Open Wall Right FSC - 1pc.

478081837 - Open Wall Left FSC - 1pc.

478081737 - After Wall FSC - 1pc.

478081637 - Bay Window Wall FSC - Right - 1pc.

478081537 - Bay Window Wall FSC - Left - 1pc.

478081437 - Door Wall FSC - Left - 1pc.

9321887 - Wall Hinge - 1pc.

S39 - 52013903 - Wood Screw #5 x 3/4" - 1pc.

If you need to order parts,

please order below part #

478082137 - Terrace Front Wall FSC - 1pc.

478082337 - Terrace Wall Left FSC - 1pc.

478082237 - Terrace Wall Right FSC - 1pc.

9321887 - Wall Hinge - 1pc.

S39 - 52013903 - Wood Screw #5 x 3/4" - 1pc.

S39 - 52013903

9321887

S39 - 52013903

9321887

12

2pc.

S5

- Pan Screw

#8 x 1/2"

- (52433502)

TN2

- 5/16" T- Nut

-

(54503300)

FW2

- 5/16" Flat Washer - (51103300)

2pc.

52pc.

S37

- Pan Screw

#7 x 5/8"

-

(52433009)

8pc.

S38

- Pan Screw

#7 x 1-1/8"

-

(52433014)

Hardware Identification

(Actual Size)

165pc.

S0

- Truss Screw

#8 x 7/8"

- (52933505)

116pc.

S20

- Wood Screw

#8 x 1-3/8"

- (52042516)

37pc.

S15

- Wood Screw

#8 x 1-3/4"

- (52043513)

14pc.

S11

- Wood Screw

#8 x 2"

- (52043520)

23pc.

S4

- Wood Screw

#8 x 3"

- (52043530)

67pc.

S3

- Wood Screw

#8 x 2-1/2"

- (52043522)

8pc.

S24

- Wood Screw

#10 x 4"

- (52043940)

2pc.

WB1

- Wafer Bolt

5/16 x 1"

- (53613310)

18pc.

S1

- Wood Screw

#8 x 1-1/8"

- (52043514)

1pc.

D4

- #2 x 2 Robertson Driver Bit - (9200014)

28pc.

FW3

- #8 Flat Washer -

(51003500)

28pc. S13 - Pan Screw #6 x 5/8" (16mm) - (52413908)

Note: Hardware bag includes extra hardware

13

(Reduced Part Size)

2x

-

Clock Chalk Sign

(3320704)

1x

- Steel Hinge (6pk)

(3207712)

1x

- Magnetic Catch Kit (3200716)

1x

- Magnetic Door Catch (3pk)

(3207713)

1x

- Door Handle (4pk)

(3207711)

1x

- Outdoor Sink Bottom Sections

(9330531)

1x -

Bay Window Assembly Top Set

(3320097)

1x

- Two Handle Hot & Cold Faucet (3320098)

2x

- Clip-In Stove Base

(9337839)

2x

- Larger Gas Burner

(9330735)

2x

- Knob

(9337836)

2x

- Clicker

(9337838)

5x

- Clip

(9337837)

1x

- Narrow Angle Bracket (8pk)

(3207832)

1x

- Pan, Pot (9320889GG)

1x

- Spatula

(9320889RD)

1x

- Jamb Mount (4pk)

(3207802)

Part Identification

1x

- Side Frame Triangle Window

(9330541)

1x

- Timber Trail Bracket (3200099)

1x

- Bay Window Assembly Bottom Set

(3320099)

1x

- Playhouse Plaque

(9320371)

14

3x

- MOD 8 Side Lite White

(9330519)

2x

- Big Triangle Window

(9330518)

2x

- Flower Pot (9330333)

1x

- Roof Water Sink

(2pk)

(3337851)

1x

- New MOD4 Side Lite (2pk)

(3330522)

- Mail Slot (9330509)

1x

- Doorbell II,

Door Trim Set (White)

(3320544)

2x

- Toybox End (9330334)

(Reduced Part Size)

Part Identification

1x

- BBQ

Lid

9327812

1x

- Tong

1x

- BBQ

Base

3331611

1x

- BBQ Assembly (3330011)

15

B. If there are any missing or damaged pieces or you need assistance with

assembly please contact the consumer relations department directly. Call us

before going back to the store.

Step 1: Inventory Parts - Read This Before Starting Assembly

• Please refer to Page 3 for proper hardware assembly.

• Each step indicates which bolts and/or screws you will need for assembly, as well as

any at washers, lock washers, t-nuts or lock nuts.

A. This is the time for you to inventory all your hardware, wood and accessories,

referencing the parts identication sheets. This will assist you with your assembly.

• The wood pieces will have the key number stamped on the ends of the boards.

Organize the wood pieces by step, as per the key numbering system below.

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)

MODEL NUMBER: P280099

Quantity Key Number

Part Description,

Part Size

1X 131 Cafe Top FSC 15.9 x 127 x 1225.6 mm

Key Number: The rst two digits represent the step

number. The third digit represents the piece. Note

that if the part is used in multiple steps then the

number only reects the rst step it is used in.

C. Read the assembly manual completely, paying special attention to ANSI warnings;

notes; and safety/maintenance information.

D. Before you discard your cartons ll out the form below.

• The carton I.D. stamp is located on the end of each carton.

• Please retain this information for future reference. You will need this information if you

contact the Consumer Relations Department.

Europe Customer Service: +31 (0)20 305 8620

[email protected]

EU Online Parts Replacement: parts.kidkraft.eu

[email protected]

Online Parts Replacement: parts.kidkraft.com

To warranty your product: kidkraft.com/warranty/

Customer Service:

1(800) 933-0771 or (972) 385-0100

16

1 x Panel Assembly

021

Wood Parts Hardware

Step 2: Frame Assembly

Part 1

12 x #8 x 2-1/2” Wood Screw

S3

021

S3

x 6 per

side

Front Wall

Back Wall

x 6 per

side

A: Place (021) Panel Assembly in the upright position and unfold all panels, making sure that the window openings

are at the top.

B: Check to make sure that the assembly is square then install 6 (S3) #8 x 2-1/2” Wood Screws in the Front Wall

and Back Wall panels. (g.2.1, 2.2)

Fig. 2.1

Fig. 2.2

17

Step 2: Frame Assembly

Part 2

Hardware

8 x #8 x 1-3/4” Wood Screw

S15

2 x Side Tie 1” x 2” x 47-7/16”

022

Wood Parts

S15

Flush to the bottom

Top View

Inside View

022

021

x 4 per

side

022

S15

C: Place 1 (022) Side Tie along the bottom of each Side Wall so they are level and ush to the bottom of the (021)

Panel Assembly. Attach using 4 (S15) #8 x 1-3/4” Wood Screws per board. (g. 2.3, 2.4, 2.5)

Fig. 2.3

Fig. 2.4

Fig. 2.5

18

Step 3: Terrace Frame Assembly

Part 1

Hardware

6 x #8 x 2-1/2” Wood Screw

S3

031

S3

1 x Terrace Panel Assembly

031

Wood Parts

A: Stand (031) Terrace Panel Assembly so that it’s in the upright position. Unfold the panels, making sure that the

larger openings are at the top, check to make sure that the assembly is square. Install 3 (S3) #8 x 2-1/2” Wood

Screws into each corner of the assembly as shown in gure 3.1 and 3.2.

Fig. 3.1

Fig. 3.2

031

19

Hardware

6 x #8 x 2-1/2” Wood Screw

S3

x 3 per

side

x 3 per

side

Top View

031

021

Step 3: Terrace Frame Assembly

Part 2

B: Position (031) Terrace Panel Assembly against the open Side Wall so that it lines up with the inside of the Front

and Back Wall Panels as shown in gure 3.4.

C: Attach from the inside of (021) Panel Assembly using 3 (S3) #8 x 2-1/2” Wood Screws per side. (g. 3.3, 3.4,

3.5, 3.6)

Fig. 3.3

Fig. 3.4

Fig. 3.5

Fig. 3.6

20

Other Parts

1 x Door Handle

2 x Door Hinge

1 x Mail Slot

Hardware

8 x #7 x 5/8” Pan Screw

S37

S0

S37

Step 4: Attach Door Panel Accessories

Part 1

1 x Door 1” x 14 13/16x 37 13/16”

Wood Parts

041

S37

Door

Hinge

x 3 per

hinge

21-3/4”

(553mm)

Door

Hinge

1”

(25.4mm)

1”

(25.4mm)

Door

Handle

Mail Slot

S0

041

A: On the left panel of (041) Door, measure 1” from the top and bottom then place 1 Door Hinge on each end.

Attach using 3 (S37) #7 x 5/8” Pan Screws per hinge. (g. 4.1, 4.2)

B: On the right panel of (041) Door, measure 21-3/4” up from the bottom and center 1 Door Handle. Attach using 2

(S37) #7 x 5/8” Pan Screws. (g. 4.3, 4.4)

C: Center the Mail Slot as shown in gure 4.5 and attach using 2 (S0) #8 x 7/8” Truss Screws (g. 4.5)

Fig. 4.1

Fig. 4.2

Fig. 4.5

Fig. 4.3

Fig. 4.4

2 x #8 x 7/8” Truss Screw

Page is loading ...

KidKraft Timber Trail Wooden Outdoor Playhouse Assembly Instruction

KidKraft Timber Trail Wooden Outdoor Playhouse Assembly Instruction

Related papers

Other documents