Fujitsu AOYA24LACL ABYA24LAT Operating instructions
- Category
- Split-system air conditioners
- Type
- Operating instructions
This manual is also suitable for
AIR CONDITIONER
FLOOR CONSOLE/
UNDER CEILING
DUAL TYPE
P/N9374379132
OPERATING MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE FUNCIONAMIENTO
MANUALE DI ISTRUZIONI
ΕΓΕΙΡΙ∆Ι ΛΕΙΤΥΡΓΙΑΣ
MANUAL DE INSTRUÇÕES
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
KULLANMA K‹TABI
Português EλληvIkά Italiano Español Français Deutsch English
Русский
Türkçe
KEEP THIS MANUAL FOR FUTURE REFERENCE
DIESE ANLEITUNG BITTE SORGFÄLTIG AUFBEWAHREN
CONSERVEZ CE MODE D’EMPLOI AFIN DE POUVOIR VOUS Y RÉFÉRER ULTÉRIEUREMENT
GUARDE ESTE MANUAL PARA PODERLO CONSULTAR EN EL FUTURO
CONSERVARE QUESTO MANUALE PER OGNI EVENTUALE FUTURO RIFERIMENTO
ΚΡΑΤΗΣΤΕ Τ ΕΓΕΙΡΙ∆Ι ΓΙΑ ΜΕΛΛΝΤΙΚΗ ΑΝΑΦΡΑ
GUARDE ESTE MANUAL PARA CONSULTA POSTERIOR
СОХРАНИТЕ НАСТОЯЩЕЕ РУКОВОДСТВО ДЛЯ БУДУЩИХ ССЫЛОК
BU KILAVUZU, DAHA SONRA BAfiVURMAK ÜZERE SAKLAYIN
9374379132_OM_cover1.p65 31/8/07, 15:481
En-1
CONTENTS
SAFETY PRECAUTIONS ....................................... 1
FEATURES AND FUNCTIONS .............................. 2
NAME OF PARTS ................................................... 2
PREPARATION ....................................................... 4
OPERATION ........................................................... 5
TIMER OPERATION ............................................... 7
SLEEP TIMER OPERATION ................................... 8
FILTER LAMP RESET ............................................. 8
MANUAL AUTO OPERATION ............................... 8
ADJUSTING THE DIRECTION OF
AIR CIRCULATION ................................................. 9
SWING OPERATION ............................................ 10
ECONOMY OPERATION...................................... 10
CLEANING AND CARE ........................................ 11
SELECTING THE REMOTE CONTROL UNIT
SIGNAL CODE ..................................................... 12
TROUBLESHOOTING .......................................... 12
OPERATING TIPS................................................. 14
SAFETY PRECAUTIONS
●Before using the appliance, read these “PRECAUTIONS” thoroughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain safe operating conditions.
●“DANGER”, “WARNING” and “CAUTION” have the following meanings in these instructions:
●Do not attempt to install this air conditioner by yourself.
●This unit contains no user-serviceable parts. Always consult authorized service per-
sonnel for repairs.
●When moving, consult authorized service personnel for disconnection and installa-
tion of the unit.
●Do not become over-exposed to cold air by staying in the direct path of the airflow of
the air conditioner for extended periods of time.
●Do not insert fingers or objects into the outlet port or intake grilles.
●Do not start and stop air conditioner operation by disconnecting the power supply
cord and so on.
●Take care not to damage the power supply cord.
●In the event of a malfunction (burning smell, etc.), immediately stop operation, turn
off the electrical breaker, and consult authorized service personnel.
●Provide occasional ventilation during use.
●Do not direct air flow at fireplaces or heating apparatus.
●Do not climb on, or place objects on, the air conditioner.
●Do not hang objects from the indoor unit.
●Do not set flower vases or water containers on top of air conditioners.
●Do not expose the air conditioner directly to water.
●Do not operate the air conditioner with wet hands.
●Do not pull power supply cord.
●Turn off power source when not using the unit for extended periods.
●Always turn off the electrical breaker whenever cleaning the air conditioner or chang-
ing the air filter.
●Connection valves become hot during Heating; handle with care.
●When restarting after a long period of disuse in the winter, turn the power switch on
at least 12 hours before starting the unit.
●Check the condition of the installation stand for damage.
●Do not place animals or plants in the direct path of the air flow.
●Do not drink the water drained from the air conditioner.
●Do not use in applications involving the storage of foods, plants or animals, precision
equipment, or art works.
●Do not apply any heavy pressure to radiator fins.
●Operate only with air filters installed.
●Do not block or cover the intake grille and outlet port.
●Ensure that any electronic equipment is at least one metre away from either the in-
door or outdoor units.
●Avoid installing the air conditioner near a fireplace or other heating apparatus.
●When installing the indoor and outdoor units, take precautions to prevent access by
infants.
●Do not use inflammable gases near the air conditioner.
CAUTION!
WARNING!
CAUTION!
This mark indicates procedures which, if improperly performed, are most likely to
result in the death of or serious injury to the user or service personnel.
This mark indicates procedures which, if improperly performed, might lead to the
death or serious injury of the user.
This mark indicates procedures which, if improperly performed, might possibly result
in personal harm to the user, or damage to property.
DANGER!
DANGER!
9374379132_OM_en.p65 31/8/07, 15:491
En-2
FEATURES AND FUNCTIONS
AUTOMATIC OPERATION
●COOLING MODEL
Merely press the START/STOP button, and the unit will
begin automatic operation in the Cooling or Dry mode as
appropriate, in accordance with the thermostat setting
and the actual temperature of the room.
●HEAT & COOL MODEL (REVERSE CYCLE)
Merely press the START/STOP button, and the unit will
begin automatic operation in either the Heating, Cooling
or Monitor modes as appropriate, in accordance with the
thermostat setting and the actual temperature of the room.
SLEEP TIMER
●COOLING MODEL
When the SLEEP timer button is pressed during Cooling
or Dry mode, the thermostat setting is gradually raised
during the period of operation. When the set time is
reached, the unit automatically turns off.
●HEAT & COOL MODEL (REVERSE CYCLE)
When the SLEEP timer button is pressed during Heating
mode, the air conditioner’s thermostat setting is gradu-
ally lowered during the period of operation; during Cool-
ing or Dry mode, the thermostat setting is gradually raised
during the period of operation. When the set time is
reached, the unit automatically turns off.
WIRELESS REMOTE CONTROL UNIT
The WIRELESS REMOTE CONTROL UNIT allows convenient
control of air conditioner operation.
OMNI-DIRECTIONAL AIR FLOW
(SWING OPERATION)
Three-dimensional control over air direction swing is possi-
ble through dual use of both an UP/DOWN air direction swing
and RIGHT/LEFT air direction swing. Since UP/DOWN air
direction flaps operate automatically according to the ope-
rating mode of the unit, it is possible to set air direction based
on the operating mode.
MILDEW-RESISTANT FILTER
The AIR FILTER has been treated to resist mildew growth,
thus allowing cleaner use and easier care.
NAME OF PARTS
Indoor Unit
1Operating Control Panel
2MANUAL AUTO button
3Remote Control Signal Receiver
4OPERATION Indicator Lamp (red)
5TIMER Indicator Lamp (green)
6FILTER Lamp (orange)
●If the TIMER indicator lamp flashes when
the timer is operating, it indicates that a
fault has occurred with the timer setting
(see page 15 AUTO Restart).
7Intake Grille
8Air Filter
9UP/DOWN Air Direction Flaps
0RIGHT/LEFT Air Direction Louvers
(behind UP/DOWN Air Direction Flaps)
ADrain Hose
4
5
6
2
3
9374379132_OM_en.p65 31/8/07, 15:492
En-3
L
N
O
M
K
H
G
I
J
NAME OF PARTS
Display panel
To facilitate explanation, the accompanying illustration
has been drawn to show all possible indicators; in ac-
tual operation, however, the display will only show those
indicators appropriate to the current operation.
1MODE button
2ECONOMY button
3SET TEMP. button ( / )
4FILTER RESET button
5SLEEP button
6FAN button
7START/STOP button
8SET button (Vertical)
9SET button (Horizontal)
0SWING button
ATIMER MODE button
BTIMER SET ( / ) button
CCLOCK ADJUST button
DRESET button
ETEST RUN button
●This button is used when installing the condi-
tioner, and should not be used under normal
conditions, as it will cause the air condition-
er’s thermostat function to operate incorrectly.
●If this button is pressed during normal opera-
tion, the unit will switch to test operation
mode, and the Indoor Unit’s OPERATION In-
dicator Lamp and TIMER Indicator Lamp will
begin to flash simultaneously.
●To stop the test operation mode, press the
START/STOP button to stop the air condi-
tioner.
FSignal Transmitter
GTemperature SET Display
HECONOMY Display
IOperating Mode Display
JSLEEP Display
KTransmit Indicator
LFan Speed Display
MSWING Display
NTimer Mode Display
OClock Display
Some indoor units may not be equipped with the func-
tions corresponding to all of the buttons on this remote
controller. The indoor unit will beep and the OPERATION,
TIMER and FILTER lamp flash when a remote controller
button is pressed if the function is not available.
Remote controller
F
1
2
7
4
5
6
8
9
0
A
CD
3
B
E
Display
Display
9374379132_OM_en.p65 31/8/07, 15:493
En-4
PREPARATION
CAUTION!
●Take care to prevent infants from acciden-
tally swallowing batteries.
●When not using the Remote Control Unit
for an extended period, remove the
batteries to avoid possible leakage and
damage to the unit.
●If leaking battery fluid comes in contact
with your skin, eyes, or mouth, imme-
diately wash with copious amounts of
water, and consult your physician.
●Dead batteries should be removed imme-
diately and disposed of properly, either in
a battery collection receptacle or to the
appropriate authority.
●Do not attempt to recharge dry batteries.
Never mix new and used batteries, or
batteries of different types.
Batteries should last about one year
under normal use. If the Remote Con-
trol Unit’s operating range becomes ap-
preciably reduced, replace the batteries
and press the RESET button with the tip
of a ballpoint pen or other small object.
Load Batteries (R03/LR03 ××
××
× 2)
1Press and slide the battery compartment lid on the re-
verse side to open it.
Slide in the direction of the arrow while pressing the mark.
2Insert batteries.
Be sure to align the battery polarities ( ) correctly.
3Close the battery compartment lid.
Set the Current time
1Press the CLOCK ADJUST button.
Use the tip of a ball-point pen or other small object to press the button.
2Use the TIMER SET ( / ) buttons to adjust the
clock to the current time.
button: Press to advance the time.
button: Press to reverse the time.
(Each time the buttons are pressed, the time will be advanced/reversed in
one-minute increments; hold the buttons depressed to change the time
quickly in ten-minute increments.)
3Press the CLOCK ADJUST button again.
This completes the time setting and starts the clock.
To Use the Remote Control Unit
●The Remote Control Unit must be pointed at signal receiver to operate correctly.
●Operating Range: About 7 meters.
●When a signal is properly received by the air conditioner, a beeping sound will
be heard.
●If no beep is heard, press the Remote Control Unit button again.
Remote Control Unit Holder
3To remove the Remote
Control Unit (when use at
hand).
1Mount the Holder. 2Set the Remote Control
Unit.
Screws
Insert
Press in
Slide up
Pull out
9374379132_OM_en.p65 31/8/07, 15:494
En-5
To Select Mode Operation
1Press the START/STOP button.
The indoor unit’s OPERATION Indicator Lamp (red) will light.
The air conditioner will start operating.
2Press the MODE button to select the desired mode.
Each time the button is pressed, the mode will change in the following
order.
AUTO COOL DRY
HEAT FAN
About three seconds later, the entire display will reappear.
To Set the Room temperature
Press the SET TEMP. button.
button: Press to raise the thermostat setting.
button: Press to lower the thermostat setting.
● Thermostat setting range:
AUTO .................................. 18-30 °C
Heating ............................... 16-30 °C
Cooling/Dry ........................ 18-30 °C
The thermostat cannot be used to set room temperature during the FAN mode (the
temperature will not appear on the Remote Control Unit’s Display).
About three seconds later, the entire display will reappear.
The thermostat setting should be considered a standard value, and may differ
somewhat from the actual room temperature.
To Set the Fan Speed
Press the FAN button.
Each time the button is pressed, the fan speed changes in the following order:
AUTO HIGH MED LOW QUIET
About three seconds later, the entire display will reappear.
When set to AUTO:
Heating: Fan operates so as to optimally circulate warmed air.
However, the fan will operate at very low speed when the temperature
of the air issued from the indoor unit is low.
Cooling: As the room temperature approaches that of the thermostat setting,
the fan speed becomes slower.
Fan: The fan runs at the low fan speed.
The fan will operate at a very low setting during Monitor operation and at the start
of the Heating mode.
QUIET Operation
When set to Quiet:
QUIET operation begins. The indoor unit’s airflow will be reduced for quieter opera-
tion.
●QUIET operation cannot be used during Dry mode. (The same is true when dry
mode is selected during AUTO mode operation.)
●During Quiet operation, Heating and Cooling performance will be reduced some-
what. If the room does not warm up/cool down when using QUIET Operation,
please adjust the air conditioner’s Fan Speed.
OPERATION
ssss s
sss
tt
Example: When set to COOL.
Example: When set to 26 °C.
Example: When set to AUTO.
9374379132_OM_en.p65 31/8/07, 15:495
En-6
To Stop Operation
Press the START/STOP button.
The OPERATION Indicator Lamp (red) will go out.
About AUTO CHANGEOVER Operation
AUTO: ●When AUTO CHANGEOVER operation first selected, the fan will ope-
rate at very low speed for about one minute, during which time the
unit detects the room conditions and selects the proper operating mode.
If the difference between thermostat setting and actual room tempera-
ture is more than +2 °C
→Cooling or dry operation
(Monitor operation may be selected if the outdoor temperature is
low.)
If the difference between thermostat setting and actual room tempera-
ture is within ±2 °C
→Monitor operation
If the difference between thermostat setting and actual room tempera-
ture is more than –2 °C
→Heating operation
(Monitor operation may be selected if the outdoor temperature is
high.)
●When the air conditioner has adjusted your room’s temperature to near
the thermostat setting, it will begin monitor operation. In the monitor
operation mode, the fan will operate at low speed. If the room tem-
perature subsequently changes, the air conditioner will once again
select the appropriate operation (Heating, Cooling) to adjust the tem-
perature to the value set in the thermostat.
(The monitor operation range is ±2 °C relative to the thermostat set-
ting.)
●If the mode automatically selected by the unit is not what you wish,
select one of the mode operation (HEAT, COOL, DRY, FAN).
About Mode Operation
Heating: ●Use to warm your room.
●When Heating mode is selected, the air conditioner will operate at very
low fan speed for about 3 to 5 minutes, after which it will switch to the
selected fan setting. This period of time is provided to allow the indoor
unit to warm up before beginning full operation.
●When the room temperature is very low, frost may form on the outside
unit, and its performance may be reduced. In order to remove such
frost, the unit will automatically enter the defrost cycle from time to
time. During Automatic Defrosting operation, the OPERATION Indica-
tor Lamp will flash, and the heat operation will be interrupted.
●After the start of heating operation, it takes some time before the room
gets warmer.
Cooling: ●Use to cool your room.
Dry: ●Use for gently cooling while dehumidifying your room.
●You cannot heat the room during Dry mode.
●During Dry mode, the unit will operate at low speed; in order to adjust
room humidity, the indoor unit’s fan may stop from time to time. Also,
the fan may operate at very low speed when adjusting room humidity.
●The fan speed cannot be changed manually when Dry mode has been
selected.
Fan: ●Use to circulate the air throughout your room.
During Heating mode:
Set the thermostat to a temperature set-
ting that is higher than the current room
temperature. The Heating mode will not
operate if the thermostat is set lower than
the actual room temperature.
During Cooling/Dry mode:
Set the thermostat to a temperature set-
ting that is lower than the current room
temperature. The Cooling and Dry modes
will not operate if the thermostat is set
higher than the actual room temperature
(in Cooling mode, the fan alone will oper-
ate).
During Fan mode:
You can not use the unit to heat and cool
your room.
9374379132_OM_en.p65 31/8/07, 15:496
En-7
TIMER OPERATION
sss
t
To Cancel the Timer
Use the TIMER MODE button to select
“CANCEL”.
The air conditioner will return to normal
operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
QUIET mode), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select
“CANCEL”.
The air conditioner will return to normal
operation.
To Change the Timer Settings
1.
Follow the instructions given in the section
“To Use the ON Timer or OFF Timer” to
select the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF ON.
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
QUIET mode), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
To Use the ON timer or OFF timer
1Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) will light.
2Press the TIMER MODE button to select the OFF timer
or ON timer operation.
Each time the button is pressed the timer function changes in the follow-
ing order:
CANCEL OFF ON
PROGRAM (OFF → ON, OFF ← ON)
The indoor unit’s green TIMER Indicator Lamp (green) will light.
3Use the TIMER SET buttons to adjust the desired OFF
time or ON time.
Set the time while the time display is flashing (the flashing will continue
for about five seconds).
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Use the Program timer
1Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (red) will light.
2Set the desired times for OFF timer and ON timer.
See the section “To Use the ON timer or OFF timer” to set the desired
mode and times.
About three seconds later, the entire display will reappear.
The indoor unit’s TIMER Indicator Lamp (green) will light.
3Press the TIMER MODE button to select the PROGRAM
timer operation (OFF ON or OFF ON will display).
The display will alternately show “OFF timer” and “ON timer”, then change
to show the time setting for the operation to occur first.
●The program timer will begin operation. (If the ON timer has been se-
lected to operate first, the unit will stop operating at this point.)
About five seconds later, the entire display will reappear.
About the Program timer
●The program timer allows you to integrate OFF timer and ON timer operations in
a single sequence. The sequence can involve one transition from OFF timer to
ON timer, or from ON timer to OFF timer, within a twenty-four hour period.
●The first timer function to operate will be the one set nearest to the current time.
The order of operation is indicated by the arrow in the Remote Control Unit’s
Display (OFF → ON, or OFF ← ON).
●One example of Program timer use might be to have the air conditioner auto-
matically stop (OFF timer) after you go to sleep, then start (ON timer) automati-
cally in the morning before you arise.
Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P. 4).
If the indoor unit is connected to a wired remote controller, the wireless remote controller cannot be used to set the timer.
9374379132_OM_en.p65 31/8/07, 15:497
En-8
FILTER LAMP RESET
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped.
If the indoor unit is connected to a wired remote controller, the wireless remote controller cannot be used to set the sleep
timer.
To Use the SLEEP Timer
While the air conditioner is operating or stopped, press the
SLEEP button.
The indoor unit’s OPERATION Indicator Lamp (red) lights and the TIMER Indicator
Lamp (green) light.
To Change the Timer Settings
Press the SLEEP button once again and set the time using the
TIMER SET ( / ) buttons.
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Cancel the Timer:
Use the TIMER MODE button to select
“CANCEL”.
The air conditioner will return to normal
operation.
To Stop the Air Conditioner During
Timer Operation:
Press the START/STOP button.
About the SLEEP Timer
To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies the thermostat setting
in accordance with the set time setting. When the set time has elapsed, the air conditioner completely stops.
SLEEP TIMER OPERATION
Some indoor unit models are equipped with a filter lamp in the indoor unit display to indicate when it is time to clean the air
filters.
To Reset Filter Lamp
Press the FILTER RESET button.
The indoor unit’s FILTER LAMP (orange) will go out.
Set time
1 hour
1 °C2 °C
2 °C3 °C4 °C
30
minutes
1 °C
1 hour
1 hour
30 minutes
Set time
During Cooling/Dry operation:
When the SLEEP timer is set, the thermostat setting is auto-
matically raised 1 °C every 1 hour. When the thermostat has
been raised a total of 2 °C, the thermostat setting at that time
is maintained until the set time has elapsed, at which time the
air conditioner automatically turns off.
SLEEP timer setting
During Heating operation:
When the SLEEP timer is set, the thermostat setting is
automatically lowered 1 °C every thirty minutes. When the
thermostat has been lowered a total of 4 °C, the thermostat
setting at that time is maintained until the set time has elapsed,
at which time the air conditioner automatically turns off.
SLEEP timer setting
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the remote control unit is lost or otherwise unavailable.
How To Use the Main Unit Controls
Press the MANUAL AUTO button on the main unit control
panel.
To stop operation, press the MANUAL AUTO button once again.
●When the air conditioner is operated
with the controls on the Main unit, it
will operate under the same mode as
the AUTO mode selected on the re-
mote control unit.
However, about Multi-type Air condi-
tioner, the Heat pump model will fol-
low the operating mode of the other
indoor unit.
●The fan speed selected will be “AUTO”
and the thermostat setting will be
24 °C.
9374379132_OM_en.p65 31/8/07, 15:498
En-9
ADJUSTING THE DIRECTION OF AIR CIRCULATION
DANGER!
Never place fingers or foreign objects inside
the outlet ports, since the internal fan ope-
rates at high speed and could cause personal
injury.
●Attempting to move UP/DOWN air di-
rection flaps or RIGHT/LEFT air direc-
tion louvers manually could result in
improper operation; in this case, stop
operation and restart. The louvers
should begin to operate properly
again.
●During use of the Cooling and Dry
modes, do not set the UP/DOWN air
direction flaps in the Heating range (5
to 7) for long periods of time, since
water vapor may condense near the
outlet louvers and drops of water may
drip from the air conditioner. During
the Cooling and Dry modes, if the Air
Flow Direction Louvers are left in the
heating range for more than 30 mi-
nutes, they will automatically return to
position 4.
●When used in a room with infants, chil-
dren, elderly or sick persons, the air
direction and room temperature
should be considered carefully when
making settings.
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
●Adjust the up, down, left and right AIR directions with the AIR DIRECTION buttons on the Remote Control Unit.
●Use the AIR DIRECTION buttons after the Indoor Unit has started operating and the airflow-direction louvers have stopped
moving.
RIGHT/LEFT air direction louvers
Vertical Air Direction Adjustment
Press the SET button (Vertical).
Each time the button is pressed, the air direction range will change as follows:
1 2 3 4 5 6 7
Types of Air flow Direction Setting:
1, 2, 3, 4: During Cooling/Dry Modes
5, 6, 7: * During Heating mode
The remote control unit’s display does
not change.
●Use the air direction adjustments within the ranges shown above.
●The vertical airflow direction is set automatically as shown, in accordance with
the type of operation selected.
During Cooling/Dry mode : Horizontal flow 1
* During Heating mode : Downward flow 7
●During AUTO mode operation, for the first minute after beginning operation,
airflow will be horizontal 1; the air direction cannot be adjusted during this pe-
riod.
Horizontal Air Direction Adjustment
Press the SET button (Horizontal).
Each time the button is pressed, the air direction range will change as follows:
1 2 3 4 5
The remote control unit’s display does
not change.
●Use the air direction adjustments within the ranges shown above.
9374379132_OM_en.p65 31/8/07, 15:499
En-10
SWING OPERATION
Begin air conditioner operation before performing this procedure.
Up/down swing operation Left/right swing operation
Swing operation stops Up/down/left/right swing operation
To select SWING Operation
Press the SWING button.
Each time the SWING button is pressed, the swing operation will change in the
following order.
To stop SWING Operation
Press the SWING button and select STOP.
Airflow direction will return to the setting before swing was begun.
About Swing Operation
The type of operation
Cooling/Dry
Heating
FAN
Range of swing
1 to 5 (All range)
1 to 5 (All range)
1 to 5 (All range)
●The SWING operation may stop temporarily when the air
conditioner’s fan is not operating, or when operating at
very low speeds.
●To select Left/right swing operation
*1 The position of the louvers before swing is given in
parenthesis.
The type of operation
Cooling/Dry
Heating
FAN (1 ~ 4)*1
FAN (5 ~ 7)*1
Range of swing
1 to 4
3 to 7
1 to 4
3 to 7
●The SWING operation may stop temporarily when the air
conditioner’s fan is not operating, or when operating at
very low speeds.
●To select Up/down swing operation
ECONOMY OPERATION
Begin Air Conditioner operation before performing this procedure.
To Use the ECONOMY Operation
Press the ECONOMY button.
“ECO” appears on the Remote Control Unit display.
Economy operation begins.
To Stop the ECONOMY Operation
Press the ECONOMY button again.
“ECO” disappears from the Remote Control Unit display.
Normal operation begins.
About ECONOMY Operation
At the maximum output, ECONOMY Operation is approximately 70% of normal air conditioner operation for cooling and
heating.
When ECONOMY operation is performed during the cooling mode, dehumidification is improved. This function is especially
convenient when you want to remove the humidity in the room without significantly lowering the room temperature.
During ECONOMY operation, the thermostat setting automatically changes according to the temperature to avoid Unneces-
sary cooling and heating for the most economical operation.
●If the room is not cooled (or heated) well during economy operation, select normal operation.
●Once air conditioner operation is stopped, normal operation begins when the indoor unit is turned on again.
●During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if
ECONOMY operation is selected by pressing the ECONOMY operation button.
9374379132_OM_en.p65 31/8/07, 15:4910
En-11
●Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply cord.
●Be sure the intake grille is installed securely.
●When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-
sonal injury may result.
CLEANING AND CARE
CAUTION!
Cleaning the Air Filter
When the FILTER Lamp is blinking, remove
the filter and clean it.
1. Pull out both sides and the center of the
intake grille.
2. Pull the air filters upward to remove them.
Push the air filter handles away from the intake grille in
direction 1, then pull out the air filters.
3. Clean the air filters.
Remove the dust from the air filters by vacuuming or
washing them. After washing, allow the air filters to dry
thoroughly in an area protected from sunlight.
4. Re-attach the air filters to the intake grille.
1The air filters fit onto the inside of the intake grille.
(Figure 1)
2The bottom edges of the air filters should fit into the
filter brackets. (Figure 1)
3The air filters should be pushed down so that their
top edges fit under the projections at the top of the
intake grille. (Figure 2)
5. Push in both sides and the center of the
intake grille.
●Dust can be cleaned from the air filter either with a vacuum
cleaner, or by washing the filter in a solution of mild de-
tergent and warm water. If you wash the filter, be sure to
allow it to dry thoroughly in a shady place before rein-
stalling.
●If dirt is allowed to accumulate on the air filter, air flow
will be reduced, lowering operating efficiency and increas-
ing noise.
●After turning the power on, press the filter button on the
remote control to turn off the filter lamp.
About 30 mm
Side Panel
Intake Grille
Notch
Arm
Hook
Handle
Intake Grille
Base
Arm
1
Air Filter
Bracket
(Figure 1)
Filter bracket
Air Filter
(Figure 2)
●When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the
unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service
personnel.
●When cleaning the unit’s body, do not use water hotter than 40 °C, harsh abrasive cleansers, or volatile agents like
benzene or thinner.
●Do not expose the unit body to liquid insecticides or hairsprays.
●If the unit will not be operated for a period of one month or more, be sure to allow the inner parts of the unit to dry
thoroughly, in advance, by operating the unit in fan mode for half a day.
9374379132_OM_en.p65 31/8/07, 15:4911
En-12
When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other
than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to
set (four selections possible).
When two or more air conditioners are installed in a room, please contact your retailer to set the individual air conditioner
signal codes.
SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE
Selecting the Remote Control Unit Signal Code
Use the following steps to select the signal code of the remote control unit. (Note
that the air conditioner cannot receive a signal code if the air conditioner has not
been set for the signal code.)
1Press the START/STOP button until only the clock is
displayed on the remote control unit display.
2Press the MODE button for at least five seconds to dis-
play the current signal code (initially set to ).
3Press the / buttons to change the signal code
between . Match the code on the display to
the air conditioner signal code.
4Press the MODE button again to return to the clock
display. The signal code will be changed.
If no buttons are pressed within 30 seconds after the signal code is displayed, the system returns to the original clock
display. In this case, start again from step 1.
The air conditioner signal code is set to A prior to shipment. Contact your retailer to change the signal code.
The remote control unit resets to signal code A when the batteries in the remote control unit are replaced. If you use a
signal code other than signal code A, reset the signal code after replacing the batteries.
If you do not know the air conditioner signal code setting, try each of the signal codes ( ) until you find the
code which operates the air conditioner.
TROUBLESHOOTING
Symptom
Doesn’t operate imme-
diately:
Noise is heard:
Problem
●If the unit is stopped and then immediately started again, the com-
pressor will not operate for about 3 minutes, in order to prevent
fuse blowouts.
●Whenever the power supply plug is disconnected and then recon-
nected to a power outlet, the protection circuit will operate for about
3 minutes, preventing unit operation during that period.
●During operation and immediately after stopping the unit, the
sound of water flowing in the air conditioner’s piping may be
heard. Also, noise may be particularly noticeable for about 2 to 3
minutes after starting operation (sound of coolant flowing).
●During operation, a slight squeaking sound may be heard. This is
the result of minute expansion and contraction of the front cover
due to temperature changes.
*●During Heating operation, a sizzling sound may be heard occa-
sionally. This sound is produced by the Automatic Defrosting
operation.
See page
—
—
14
NORMAL
FUNCTION
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the
power supply plug or turn off the circuit breaker, and consult authorized service personnel.
Merely turning off the unit’s power switch will not completely disconnect the unit from the power
source. Always be sure to disconnect the power supply plug or turn off your circuit breaker to
ensure that power is completely off.
Before requesting service, perform the following checks:
WARNING!
9374379132_OM_en.p65 31/8/07, 15:4912
En-13
TROUBLESHOOTING
Symptom
Smells:
Mist or steam are
emitted:
Airflow is weak or stops:
Water is produced from
the outdoor unit:
The FILTER lamp blinks:
Doesn’t operate at all:
Poor Cooling (or *Heating)
performance:
The unit operates differ-
ently from the remote con-
trol unit’s setting:
Signal is not received after
replacing the batteries for
the remote control unit:
Problem
●Some smell may be emitted from the indoor unit. This smell is
the result of room smells (furniture, tobacco, etc.) which have
been taken into the air conditioner.
●During Cooling or Dry operation, a thin mist may be seen emitted
from the indoor unit. This results from the sudden Cooling of
room air by the air emitted from the air conditioner, resulting in
condensation and misting.
*●During Heating operation, the outdoor unit’s fan may stop, and
steam may be seen rising from the unit. This is due to the Auto-
matic Defrosting operation.
*●When Heating operation is started, fan speed is temporarily very
low, to allow internal parts to warm up.
*●During Heating operation, if the room temperature rises above
the thermostat setting, the outdoor unit will stop, and the indoor
unit will operate at very low fan speed. If you wish to warm the
room further, set the thermostat to a higher setting.
*●During Heating operation, the unit will temporarily stop opera-
tion (between 7 and 15 minutes) as the Automatic Defrosting mode
operates. During the Automatic Defrosting operation, the OPERA-
TION indicator lamp will flash.
●The fan may operate at very low speed during Dry operation or
when the unit is monitoring the room’s temperature.
●During QUIET operation, the fan will operate at very low speed.
●In the monitor AUTO operation, the fan will operate at very low
speed.
*●During Heating operation, water may be produced from the out-
door unit due to the Automatic Defrosting operation.
●Clean the filter. Afterwards, turn the FILTER lamp off.
●Has the circuit breaker been turned off?
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
●Is the timer operating?
●Is the air filter dirty?
●Are the air conditioner’s intake grille or outlet port blocked?
●Did you adjust the room temperature settings (thermostat) cor-
rectly?
●Is there a window or door open?
●In the case of Cooling operation, is a window allowing bright sun-
light to enter? (Close the curtains.)
●In the case of Cooling operation, are there heating apparatus and
computers inside the room, or are there too many people in the
room?
●Is the unit set for QUIET operation?
●Are the remote control unit’s batteries dead?
●Are the remote control unit’s batteries loaded properly?
●Are you using an air conditioner signal code other than signal
code A?
See page
—
—
14
—
14
—
—
—
14
8
—
7 to 8
—
—
4
12
NORMAL
FUNCTION
CHECK ONCE
MORE
If the problem persists after performing these checks, or if you notice burning smells, or the TIMER indicator lamp and opera-
tion indicator lamp flashes, stop operation immediately, disconnect the power supply plug, and consult with authorized
service personnel.
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
9374379132_OM_en.p65 31/8/07, 15:4913
En-14
OPERATING TIPS
*Heating Performance
●This air conditioner operates on the heat-pump principle,
absorbing heat from outdoor air and transferring that heat
indoors. As a result, the operating performance is reduced
as outdoor air temperature drops. If you feel that insuffi-
cient heating performance is being produced, we recom-
mend you use this air conditioner in conjunction with
another kind of heating appliance.
●Heat-pump air conditioners heat your entire room by
recirculating air throughout the room, with the result that
some time may be required after first starting the air con-
ditioner until the room is heated.
*
When Indoor and Outdoor Temperature are High
●When both indoor and outdoor temperatures are high
during use of the heating mode, the outdoor unit’s fan
may stop at times.
*Fan speed: AUTO
Heating: The fan will operate at very low speed when the
temperature of the air issued from the indoor unit
is low.
Cooling: As the room temperature approaches that of the
set temperature, the fan speed becomes slower.
Fan: The fan runs at the low fan speed.
*Microcomputer-controlled Automatic Defrosting
●When using the Heating mode under conditions of low
outdoor temperature and high humidity, frost may form
on the outdoor unit, resulting in reduced operating per-
formance.
In order to prevent this kind of reduced performance, this
unit is equipped with a Microcomputer-controlled Auto-
matic Defrosting function. If frost forms, the air condi-
tioner will temporarily stop, and the defrosting circuit will
operate briefly (for about 4 to 15 minutes).
During Automatic Defrosting operation, the OPERATION
indicator lamp (red) will flash.
*Low Ambient Cooling
●When the outdoor temperature drops, the outdoor unit’s
fans may switch to Low Speed.
*Hot start (for heating)
●The indoor unit prevents cold drafts when heating opera-
tion begins.
The indoor unit fan will not operate or it will operate at a
very low speed until the heat exchanger reaches the set
temperature.
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
HEAT & COOL MODEL (Reverse Cycle)
Auto changeover function
●When AUTO CHANGEOVER is selected, the air conditioner
selects the appropriate operation mode (Cooling or Heat-
ing) according to your room’s present temperature.
●When AUTO CHANGEOVER is first selected, the fan will
operate at a very low speed for about 1 minute while the
unit determines the current conditions of the room and
selects the proper operation mode.
If the difference between thermostat setting and actual
room temperature is more than +2 °C
→Cooling or dry operation
(Monitor operation may be selected if the outdoor tem-
perature is low.)
If the difference between thermostat setting and actual
room temperature is within ±2 °C
→Monitor operation
If the difference between thermostat setting and actual
room temperature is more than –2 °C
→Heating operation
(Monitor operation may be selected if the outdoor tem-
perature is high.)
Mode operation: AUTO
COOLING MODEL
●When the room temperature is 2 °C higher than the set
temperature, the mode will switch between Cooling and
Drying.
●When the room temperature is near the thermostat set-
ting, the air conditioner will begin monitor operation. In
the monitor operation mode, the fan will operate at a very
low speed. If the room temperature subsequently
changes, the air conditioner will once again select the
appropriate operation (Heating or Cooling) to adjust the
temperature to the value set in the thermostat. (The moni-
tor operation range is ±2 °C relative to the thermostat
setting.)
●During the Drying mode operation, the FAN setting should
be switched to LOW for a gently cooling effect during
which the fan may temporarily stop rotating.
9374379132_OM_en.p65 31/8/07, 15:4914
En-15
During Heating mode:
Set the thermostat to a temperature set-
ting that is higher than the current room
temperature. The Heating mode will not
operate if the thermostat is set lower than
the actual room temperature.
During Cooling/Dry mode:
Set the thermostat to a temperature set-
ting that is lower than the current room
temperature. The Cooling and Dry modes
will not operate if the thermostat is set
higher than the actual room temperature
(in Cooling mode, the fan alone will ope-
rate).
During Fan mode:
You can not use the unit to heat and cool
your room.
About Mode Operation
Heating: ●Use to warm your room.
●When Heating mode is selected, the air conditioner will operate at very
low fan speed for about 3 to 5 minutes, after which it will switch to the
selected fan setting. This period of time is provided to allow the indoor
unit to warm up before beginning full operation.
●When the room temperature is very low, frost may form on the outside
unit, and its performance may be reduced. In order to remove such
frost, the unit will automatically enter the defrost cycle from time to
time. During Automatic Defrosting operation, the OPERATION indica-
tor Lamp will flash, and the heat operation will be interrupted.
●After the start of heating operation, it takes sometime before the room
gets warmer.
Cooling: ●Use to cool your room.
Dry: ●Use for gently cooling while dehumidifying your room.
●You cannot heat the room during Dry mode.
●During Dry mode, the unit will operate at low speed; in order to adjust
room humidity, the indoor unit’s fan may stop from time to time. Also,
the fan may operate at very low speed when adjusting room humidity.
●The fan speed cannot be changed manually when Dry mode has been
selected.
Fan: ●Use to circulate the air throughout your room.
●Should the power supply to the air conditioner be inter-
rupted by a power failure, the air conditioner will restart
automatically in the previously selected mode once the
power is restored.
●Should a power failure occur during TIMER operation,
the timer will be reset and the unit will begin (or stop)
operating under the new timer setting. In this event, the
TIMER indicator lamp (green) will flash.
●Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the
air conditioner to malfunction. In this event, temporarily
disconnect the power supply plug, reconnect it, and then
use the remote control unit to resume operation.
AUTO Restart
In Event of Power Interruption
Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
*●During use of the heating mode, the top of the indoor
unit may become warm, but this is due to the fact that
coolant is circulated through the indoor unit even when
it is stopped; it is not a malfunction.
Notice
*●During use of the heating mode, the outdoor unit will
occasionally commence the defrost operation for brief
periods. During the defrosting operation, if the user sets
the indoor unit for heating again, the defrosting mode
will continue, and the heating operation will begin after
completion of defrosting, with the result that some time
may be required before warm air is emitted.
OPERATING TIPS
9374379132_OM_en.p65 31/8/07, 15:4915
9374379132_OM_en.p65 31/8/07, 15:4916
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Fujitsu AOYA24LACL ABYA24LAT Operating instructions
- Category
- Split-system air conditioners
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Fujitsu ASYA07LBCM AOYA18LAC2 Operating instructions
-
-
-
-
-
-
-
-
-
