Signature Kitchen Suite SKSCW181RP User guide
- Category
- Fridges
- Type
- User guide
Eective 6/20 | WCAG
INTEGRATED COLUMN
Page 2 of 19 | Effective 6/20 | WCAG
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
24" (610 mm)
min. depth
84"
(2134 mm)
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
Notes
Refrigerator can be installed ush with 3/4" custom panel
or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
refrigerator ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through oor or back wall.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This refrigerator
is equipped with a 2-position door stop. The factory-set
115° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 14" (356 mm).
TOP VIEW
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
24" (610 mm)
min. depth
84"
(2134 mm)
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
INTEGRATED COLUMN
24-INCH INTEGRATED COLUMN
REFRIGERATOR CUTOUT DIMENSIONS –
FLUSH INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet * exterior is
recommended on all sides and the top of the cutout opening. The shaded area will
be visible after installation.
Notes
Refrigerator can be installed flush with 3/4" custom panel or optional
stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
refrigerator fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Water Line
A cold water supply is required for water dispenser operation.
Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through floor or back wall.
24-INCH INTEGRATED COLUMN
REFRIGERATOR INSTALLATION CLEARANCES –
FLUSH INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This refrigerator is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom
handle used. When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the door handle
clearance with door open 115° is 14" (356 mm).
Page 3 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
30" (762 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P
30-INCH INTEGRATED COLUMN
REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
30" (762 mm)
finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
29 3/4"
(756 mm)
30" (762 mm)
25"
(635 mm)
13 7/8"*
(352 mm)
31 1/2"
(800 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
24" (610 mm)
min. depth
84"
(2134 mm)
Notes
Refrigerator can be installed ush with 3/4" custom panel
or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
refrigerator ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through oor or back wall.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This refrigerator
is equipped with a 2-position door stop. The factory-set
115° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 16" (406 mm).
TOP VIEW
30" (762 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P
30-INCH INTEGRATED COLUMN
REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
30" (762 mm)
finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
29 3/4"
(756 mm)
30" (762 mm)
25"
(635 mm)
13 7/8"*
(352 mm)
31 1/2"
(800 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
24" (610 mm)
min. depth
84"
(2134 mm)
30-INCH INTEGRATED COLUMN
REFRIGERATOR CUTOUT DIMENSIONS –
FLUSH INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet *
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
Notes
Refrigerator can be installed flush with 3/4" custom panel or optional
stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
refrigerator fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through floor or back wall.
30-INCH INTEGRATED COLUMN
REFRIGERATOR INSTALLATION CLEARANCES
– FLUSH INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The
door panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This refrigerator
is equipped with a 2-position door stop. The factory-set
115° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from
adjacent cabinets or walls. This clearance will vary depending on the
custom handle used. When using the Stainless Steel Door Panel Kit
w/Handle or the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 16" (406 mm).
Page 4 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
SKSCF1801P
18" INTEGRATED
COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
18" (457 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"
(35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
17 3/4" (451 mm)
finished width
4"
(102 mm)
finished
return*
24" (610 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
1 3/8"(35 mm)
1/4"
(6 mm)
min.
1/4"
min.
(6 mm)
90°
115°
8 3/4"*
(223 mm)
25"
(635 mm)
19 1/2"
(495 mm)
18"
17 3/4"
(451 mm)
3/4"
(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – FLUSH INSTALLATION WITH TRIM PIECE
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
8 3/4"*
(223 mm)
25"
(635 mm)
19 1/2"
(495 mm)
18"
17 3/4"
(451 mm)
3/4"
(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
8 3/4"*
(223 mm)
17 3/4"
(451 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
3/4"
(19 mm)**
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
Notes
Freezer can be installed ush or proud with 3/4" custom
panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of
the freezer ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and 120
p.s.i.
Tubing should be long enough to extend to the front of
the freezer. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through oor or back wall.
Install a shut-o valve between the icemaker water valve
and cold water supply in the home.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 11" (279 mm).
TOP VIEW
SKSCF1801P
18" INTEGRATED
COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
18" (457 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"(35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
SINGLE COLUMN
17 3/4" (451 mm)
finished width
4"
(102 mm)
finished
return*
24" (610 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to
unfinished cabinet returns.
*
1 3/8"(35 mm)
1/4"
(6 mm)
min.
1/4"
min.
(6 mm)
90°
115°
8 3/4"*
(223 mm)
25"
(635 mm)
19 1/2"
(495 mm)
18"
17 3/4"
(451 mm)
3/4"
(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – FLUSH INSTALLATION WITH TRIM PIECE
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
8 3/4"*
(223 mm)
25"
(635 mm)
19 1/2"
(495 mm)
18"
17 3/4"
(451 mm)
3/4"
(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
8 3/4"*
(223 mm)
17 3/4"
(451 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
3/4"
(19 mm)**
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
18-INCH INTEGRATED COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH
INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet * exterior is
recommended on all sides and the top of the cutout opening. The shaded area will be
visible after installation.
Notes
Freezer can be installed flush or proud with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
freezer fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and 120
p.s.i.
Tubing should be long enough to extend to the front of the freezer.
Allow enough tubing to accommodate a bend leading into the water line
connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold
water supply in the home.
18-INCH INTEGRATED COLUMN FREEZER
INSTALLATION CLEARANCES – FLUSH
INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearance to adjacent cabinets
or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom
handle used. When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the door handle
clearance with door open 115° is 11" (279 mm).
Page 5 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
SKSCF2401P
24" INTEGRATED
COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"
(35 mm)
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
11 3/8"*
(288 mm)
25"
(635 mm)
25 1/2"
(648 mm)
24"
23 3/4"
(603 mm)
3/4"
(19 mm)**
(610 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
Notes
Freezer can be installed ush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of
the freezer ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to the front of
the freezer. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through oor or back wall.
Install a shut-o valve between the icemaker water valve
and cold water supply in the home.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 14" (356 mm).
TOP VIEW
SKSCF2401P
24" INTEGRATED
COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
24" (610 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"(35 mm)
1/8"
(3 mm)
min.
1/8"
min.
(3 mm)
90°
115°
11 3/8"*
(288 mm)
25"
(635 mm)
25 1/2"
(648 mm)
24"
23 3/4"
(603 mm)
3/4"
(19 mm)**
(610 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
24-INCH INTEGRATED COLUMN
FREEZER CUTOUT DIMENSIONS – FLUSH
INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet * exterior is
recommended on all sides and the top of the cutout opening. The shaded area will
be visible after installation.
Notes
Freezer can be installed flush with 3/4" custom panel or optional
stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
freezer fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker operation.
Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the
freezer. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold
water supply in the home.
24-INCH INTEGRATED COLUMN FREEZER
INSTALLATION CLEARANCES – FLUSH
INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom
handle used. When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the door handle
clearance with door open 115° is 14" (356 mm).
Page 6 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
30" (762 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCF3001P
30-INCH INTEGRATED
COLUMN FREEZER
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
29 3/4"
(756 mm)
30" (762 mm)
25"
(635 mm)
13 7/8"*
(352 mm)
31 1/2"
(800 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
Notes
Freezer can be installed ush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of
the freezer ts ush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker
operation. Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to extend to the front of
the freezer. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through oor or back wall.
Install a shut-o valve between the icemaker water valve
and cold water supply in the home.
Notes
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 16" (406 mm).
30" (762 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCF3001P
30-INCH INTEGRATED
COLUMN FREEZER
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
29 3/4"
(756 mm)
30" (762 mm)
25"
(635 mm)
13 7/8"*
(352 mm)
31 1/2"
(800 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
4"
(102 mm)
water location
25" (635 mm)
min. depth
84"
(2134 mm)
TOP VIEW
30-INCH INTEGRATED COLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH
INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet *
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
Freezer can be installed flush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
freezer fits flush with 25" (635 mm) depth adjacent
cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker operation.
Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the
freezer. Allow enough tubing to accommodate a bend
leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold
water supply in the home.
30-INCH INTEGRATED COLUMN
FREEZER INSTALLATION CLEARANCES
– FLUSH INSTALLATION TOP VIEW
Door handle must be * added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This freezer is
equipped with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to adjacent
cabinets or walls is restricted.
be added to the dimension noted to determine the total clearances
required from adjacent cabinets or walls. This clearance will vary
depending on the custom handle used. When using the Stainless Steel
Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional
accessories), the door handle clearance with door open 115° is 16" (406
mm).
Page 7 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
SKSCW181RP
18" INTEGRATED COLUMN
WINE REFRIGERATOR WITHOUT TRIM PIECE
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
18" (457 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"
(35 mm)
3/4"
(19 mm)**
90°
115°
19 1/2"
(495 mm)
17 3/4"
(451 mm)
8 3/4"*
(223 mm)
25"
(635 mm)
1/4"
(6 mm)
min.
1/4"
min.
(6 mm)
18" (457 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
Notes
Wine refrigerator can be installed ush with 3/4" custom
panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of
the wine refrigerator ts ush with 25" (635 mm) depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Notes
Door Swing Clearances – The installation must allow
for clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 11" (279 mm).
TOP VIEW
SKSCW181RP
18" INTEGRATED COLUMN
WINE REFRIGERATOR WITHOUT TRIM PIECE
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
18" (457 mm)
finished width
4"
(102 mm)
finished
return*
25" (635 mm)
min. depth
84"
(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
1 3/8"(35 mm)
3/4"
(19 mm)**
90°
115°
19 1/2"
(495 mm)
17 3/4"
(451 mm)
8 3/4"*
(223 mm)
25"
(635 mm)
1/4"
(6 mm)
min.
1/4"
min.
(6 mm)
18" (457 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
18-INCH INTEGRATED COLUMN WINE
REFRIGERATOR CUTOUT DIMENSIONS –
FLUSH INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet * exterior is
recommended on all sides and the top of the cutout opening. The shaded area will
be visible after installation.
Notes
Wine refrigerator can be installed flush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the wine
refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
18-INCH INTEGRATED COLUMN WINE
REFRIGERATOR INSTALLATION CLEARANCES –
FLUSH INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from adjacent
cabinets or walls. This clearance will vary depending on the custom
handle used. When using the Stainless Steel Door Panel Kit w/Handle or
the Brushed Aluminum Handle (optional accessories), the door handle
clearance with door open 115° is 11" (279 mm).
Page 8 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"
(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
25" (635 mm)
min. depth
84"
(2134 mm)
Notes
Wine refrigerator can be installed ush with 3/4" custom
panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of
the wine refrigerator ts ush with 25" (635 mm) depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Notes
Door Swing Clearances – The installation must allow
for clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must
be added to the dimension noted to determine the total
clearances required from adjacent cabinets or walls. This
clearance will vary depending on the custom handle used.
When using the Stainless Steel Door Panel Kit w/Handle
or the Brushed Aluminum Handle (optional accessories),
the door handle clearance with door open 115° is 14"
(356 mm).
TOP VIEW
24" (610 mm)
finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SINGLE COLUMN
4"
(102 mm)
finished
return*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
**
Varies depending on the
thickness of the custom
cabinet panel. The door
panels in the optional
Signature Kitchen Suite
stainless steel door panel
kit are 3/4" (19 mm) thick.
Door handle must be
added to this dimension.
*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet
exterior is recommended on all sides and the top of the cutout
opening. The shaded area will be visible after installation.
*
3/4"
(19 mm)**
115°
90°
1/8"
(3 mm)
1/8"
min.
min.
(3 mm)
23 3/4"
(603 mm)
24" (610 mm)
25"
(635 mm)
11 3/8"*
(288 mm)
25 1/2"
(648 mm)
1 1/4"*
(32 mm)
5"
(127 mm)
electrical
location
25" (635 mm)
min. depth
84"
(2134 mm)
24-INCH INTEGRATED COLUMN WINE
REFRIGERATOR CUTOUT DIMENSIONS –
FLUSH INSTALLATION SINGLE COLUMN
Notes
Wine refrigerator can be installed flush with 3/4" custom panel or
optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the
wine refrigerator fits flush with 25" (635 mm) depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.
24-INCH INTEGRATED COLUMN WINE
REFRIGERATOR INSTALLATION CLEARANCES –
FLUSH INSTALLATION TOP VIEW
* Door handle must be added to
this dimension.
** Varies depending on the thickness
of the custom cabinet panel. The door
panels in the optional Signature
Kitchen Suite stainless steel door
panel kit are 3/4" (19 mm) thick.
Door Swing Clearances – The installation must allow for
clearances to adjacent walls or cabinets. This wine
refrigerator is equipped with a 2-position door stop. The
factory-set 115° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the
dimension noted to determine the total clearances required from
adjacent cabinets or walls. This clearance will vary depending on the
custom handle used. When using the Stainless Steel Door Panel Kit
w/Handle or the Brushed Aluminum Handle (optional accessories), the
door handle clearance with door open 115° is 14" (356 mm).
Page 9 of 19 | Effective 6/20 | WCAG
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Handle
(Handle size and position must
be considered to avoid interference)
Adjacent Handle
(Handle size and position must
be considered to avoid interference)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Hinge at 115° Opening
Adjacent Cabinet /Appliance Closed Door Panel
Hinge at 90° Opening
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Cabinet /Appliance
Adjacent Cabinet /Appliance with Custom Door Panel
Closed Door Panel
Closed Custom Door Panel
Hinge at 115° Opening
Hinge at 90° Opening
TOP VIEW
DOOR SWING RANGE DIMENSIONS
3/4"
(19 mm)
1 1/2"
(38 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Handle
(Handle size and position must
be considered to avoid interference)
Adjacent Handle
(Handle size and position must
be considered to avoid interference)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Hinge at 115° Opening
Adjacent Cabinet /Appliance Closed Door Panel
Hinge at 90° Opening
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Cabinet /Appliance
Adjacent Cabinet /Appliance with Custom Door Panel
Closed Door Panel
Closed Custom Door Panel
Hinge at 115° Opening
Hinge at 90° Opening
TOP VIEW
DOOR SWING RANGE DIMENSIONS
3/4"
(19 mm)
1 1/2"
(38 mm)
Notes
The installation must allow for proper
clearances to adjacent appliances,
walls or cabinets. There should be no
interference when doors are opened.
The space needed for the hinge and
the distance to the adjacent cabinetry
and its handle is shown with both 3/4"
(19 mm) and 1 1/2" (38 mm) thick door
panels.
If interference is an issue, the following
solutions can be considered:
• Limit the door swing angle to 90° with
a door stop pin inserted into the hinge.
• Install a spacer between the appliance
and the opposing element that
creates the interference.
• If the door panel thickness is larger
than 3/4" (19mm), consider reducing it.
• Rearrange surrounding cabinetry
or appliances to eliminate the
interference.
• Create a protruding cutout for the
appliance (see page 6 for “retrot”
installation).
INTEGRATED COLUMN
PANEL
PANEL
DOOR SWING DIMENSIONS Notes
The installation must allow for proper
clearances to adjacent appliances,
walls or cabinets. There should be no
interference when doors are opened.
The space needed for the hinge and the
distance to the adjacent cabinetry and
its handle is shown with both 3/4" (19
mm) and 1 1/2" (38 mm) thick door
panels.
If interference is an issue, the following
solutions can be considered:
Notes
When installing multiple columns in a ush installation with the same door swing (handle to hinge), considerations must be
made to avoid door swing interference. The examples shown assume a 3/4" panel and the Signature Kitchen Suite handle.
Door panel thickness, handle size / position and door swing range should always be considered when determining the size
of the spacer in any installation. See page 6 for details on door swing dimensions for proper planning.
Page 10 of 19 | Effective 6/20 | WCAG
Integrated columns can be combined in cutout widths of 42", 48", 54" and 60".
- The SKSFJ800P Joining Kit is required between units (kit included with all freezer columns.)
- Reference the cutout dimensions for each column for detailed dimensions.
- A minimum 15 amp (115V, 60Hz) power supply is required for each individual column.
- A cold water supply is required for water dispenser and automatic icemaker operation for each applicable column.
1 3/4" (44 mm) min.
spacer required*
TOP VIEW
DOOR OPEN 115˚ HANDLE TO HINGE
1 3/4" (44 mm) min.
spacer required*
Handle size and position
must be considered to
avoid interference.
TOP VIEW
DOOR OPEN 90˚ HANDLE TO HINGE
3/4" (19 mm) min.
spacer required**
3/4" (19 mm) min.
spacer required**
*When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, a minimum spacer of
1 3/4" (44 mm) between units is required to open each door 115° without interference.
**When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, the door swing can
be limited to 90°, reducing the minimum spacer between units to 5/8" (16 mm).
Handle size and position
must be considered to
avoid interference.
1 3/4" (44 mm) min.
spacer required*
TOP VIEW
DOOR OPEN 115˚ HANDLE TO HINGE
1 3/4" (44 mm) min.
spacer required*
Handle size and position
must be considered to
avoid interference.
TOP VIEW
DOOR OPEN 90˚ HANDLE TO HINGE
*When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, a minimum spacer of
1 3/4" (44 mm) between units is required to open each door 115° without interference.
INTEGRATED COLUMN
INSTALLATION CLEARANCES – MULTIPLE COLUMNS WITH SAME DOOR SWING (HANDLE TO HINGE)
TOP VIEW – DOOR OPEN 115˚ HANDLE TO HINGE
TOP VIEW – DOOR OPEN 90˚ HANDLE TO HINGE
CABINETRY PLANNING
Framed Cabinet
Cabinet door
hinges mount
to the face frame
Frameless (European) Cabinet
Cabinet door
hinges mount
to the cabinet
interior
CABINETRY PLANNING
Flush Inset
Appliance 25" (635 mm)
Cutout Depth
Door Panel
25" (635 mm)
Cutout Depth
Flush Inset
Door Panel
Appliance
Filler required with a
finished return on both
sides of the appliance
Framed Cabinet
Cabinet door
hinges mount
to the face frame
Frameless (European) Cabinet
Cabinet door
hinges mount
to the cabinet
interior
CABINETRY PLANNING
Flush Inset
Appliance 25" (635 mm)
Cutout Depth
Door Panel
25" (635 mm)
Cutout Depth
Flush Inset
Door Panel
Appliance
Filler required with a
finished return on both
sides of the appliance
INTEGRATED COLUMN
Notes
Integrated column appliances
are designed to accommodate
nearly any type of cabinetry door
installation. The required cutout
depth depends on the desired
cabinetry and custom panel
execution, whether North American
styles that feature a face frame or
European styles that are frameless.
Notes
These units are designed to be customized with decorative panels. Field-installed
custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting
panel brackets (provided with unit). Adjustment screws and instructions also provided
with units.
Maximum Total Door Panel Weights:
30-Inch Integrated Column – 64 lbs.
24-Inch Integrated Column – 53 lbs.
18-Inch Integrated Column – 44 lbs
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended
that both sides of each cutout panel be nished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unnished.
Door Handles: Handles are not included with the units. Custom handles are required for
installation. Brushed Aluminum Handles are available as an optional accessory.
Page 11 of 19 | Effective 6/20 | WCAG
CABINETRY PLANNING
FRAMED CABINET
(NORTH AMERICA)
FRAMELESS CABINET
(EUROPEAN)
Integrated column appliances are
designed to accommodate nearly any
type of cabinetry door installation. The
required cutout depth depends on the
desired cabinetry and custom panel
execution, whether North American
styles that feature a face frame or
European styles that are frameless.
CUSTOM PANEL PLANNING
Page 12 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
SKSCF1801P
18" INTEGRATED
COLUMN FREEZER
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm) 4" (102 mm)
4" (102 mm)
Door Panel
(451 mm)
17 3/4"
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
(756 mm)
29 3/4"
Door Panel
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
Door Panel
(451 mm)
17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCF2401P
24-INCH INTEGRATED
COLUMN FREEZER
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
(603 mm)
23 3/4"
Door Panel
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm)4" (102 mm)
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
41 1/2" (1054 mm)
Toekick Width
47 1/2" (1207 mm)
Toekick Width
4" (102 mm) 4" (102 mm) 4" (102 mm)
4" (102 mm)
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4"(1213 mm)
(756 mm)
29 3/4"
DUAL 18" AND 30" COLUMN DUAL 24" AND 30" COLUMN
SKSCF3001P
30-INCH INTEGRATED
COLUMN FREEZER
Door Panel Door Panel 79 7/8"
(2029 mm)
(451 mm)
17 3/4"
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 30" AND 30" COLUMN
59 3/4"(1518 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(756 mm)
29 3/4"
Door Panel
4" (102 mm) 4" (102 mm) 4" (102 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
4"
(102 mm)
Door Panel
(451 mm)
17 3/4"
4" (102 mm)4" (102 mm)
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
SKSCW181RP
18" INTEGRATED
WINE COLUMN
79 7/8"
(2029 mm)
9 3/8"
(238 mm)
7 1/16"
(179.5 mm)
3 3/16"
(81 mm)
3 3/16"
(81 mm)
(451 mm)
17 3/4"
4" (102 mm)
SKSCW181RP
18" INTEGRATED
WINE COLUMN
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
79 7/8"
(2029 mm)
9 3/8"
(238mm)
7 1/16"
(179.5 mm)
(603 mm)
23 3/4"
3 3/16"
(81 mm)
3 3/16"
(81 mm)
4" (102 mm)
CUSTOM PANEL DIMENSIONS
18-INCH INTEGRATED
COLUMN FREEZER
24-INCH INTEGRATED COLUMN
REFRIGERATOR AND FREEZER
30-INCH INTEGRATED COLUMN
REFRIGERATOR AND FREEZER
18-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
Page 13 of 19 | Effective 6/20 | WCAG
Door Panel
(451 mm)
17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
(603 mm)
23 3/4"
Door Panel
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4"
(1060 mm)
41 1/2" (1054 mm)
Toekick Width
47 1/2" (1207 mm)
Toekick Width
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm)
4" (102 mm)
4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
Notes
These units are designed to be customized with decorative
panels. Field-installed custom door panels or an optional
Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to
pre-drill holes for mounting panel brackets (provided with unit).
Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights:
30-Inch Integrated Column – 64 lbs.
24-Inch Integrated Column – 53 lbs.
18-Inch Integrated Column – 44 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture
return. It is recommended that both sides of each cutout panel be
nished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom
of case is unnished.
Door Handles: Handles are not included with the units. Custom
handles are required for installation. Brushed Aluminum Handles
are available as an optional accessory.
Door Panel
(451 mm)
17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
(603 mm)
23 3/4"
Door Panel
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)
Toekick Width
47 1/2" (1207 mm)
Toekick Width
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm)
4" (102 mm)
4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
INTEGRATED COLUMN
Door Panel
(451 mm)
17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
(603 mm)
23 3/4"
Door Panel
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)
Toekick Width
47 1/2" (1207 mm)
Toekick Width
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm)
4" (102 mm)
4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
CUSTOM PANEL DIMENSIONS FOR MULTIPLE COLUMNS
DUAL 18-INCH AND 24-INCH
INTEGRATED COLUMNS
DUAL 24-INCH AND 24-INCH
INTEGRATED COLUMNS
DUAL 24-INCH AND 30-INCH
INTEGRATED COLUMNS These units are designed to be customized with decorative
panels. Field-installed custom door panels or an optional
Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill
holes for mounting panel brackets (provided with unit).
Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights:
30-Inch Integrated Column — 64 |bs.
24-Inch Integrated Column =53 |bs.
18-Inch Integrated Column - 44 Ibs.
4" (102 mm) will be visible on the interior sides of the furniture
return. It is recommended that both sides of each cutout panel be
finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is
unfinished.
Door Handles: Handles are not included with the units. Custom
handles are required for installation. Brushed Aluminum Handles
are available as an optional accessory.
INTEGRATED COLUMN
Units can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and
one handle. This kit is reversible and can be used in both Right Hand and Left Hand door swing installations.
SKSPK185CS –Stainless Steel Panel Kit for 18-inch Integrated Column Freezer
SKSPK245CS – Stainless Steel Panel Kit for 24-inch Integrated Column Refrigerator and Freezer
SKSPK305CS – Stainless Steel Panel Kit for 30-inch Integrated Column Refrigerator and Freezer
This unit can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick
and one handle. Order right or left hinge option, depending on desired installation.
Right Hinge – 1 Horizontal brushed hairlines for right hinge installation, opening from left to right
Left Hinge – 1 Horizontal brushed hairlines for left hinge installation, opening from right to left
SKSWK185RS – 18" Wine Column Stainless Kit, Right Hinge
SKSWK185LS – 18" Wine Column Stainless Kit, Left Hinge
SKSWK245RS – 24" Wine Column Stainless Kit, Right Hinge
SKSWK245LS – 24" Wine Column Stainless Kit, Left Hinge
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
SKSHK480HS – 48" (1219 mm) Long Handle – Brushed Aluminum
SKSFJ800P – This kit is required for installation when a wine column is installed with another wine column,
refrigerator column or French door column. This kit is included with all freezer columns.
Page 14 of 19 | Effective 6/20 | WCAG
SKSCW241RP
24-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
OPTIONAL ACCESSORIES
SKSCW181RP
18-INCH INTEGRATED COLUMN
WINE REFRIGERATOR
OPTIONAL ACCESSORIES
SKSCF3001P
30-INCH INTEGRATED
COLUMN FREEZER
OPTIONAL ACCESSORIES
SKSCF2401P
24-INCH INTEGRATED
COLUMN FREEZER
OPTIONAL ACCESSORIES
SKSCF1801P
18-INCH INTEGRATED
COLUMN FREEZER
OPTIONAL ACCESSORIES
Page 15 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
SKSFD3604P
36-INCH BUILT-IN FRENCH DOOR
REFRIGERATOR
CUSTOM PANEL DIMENSIONS
17 13/16"
(452 mm)
A
B
C
A
17 13/16"
(452 mm)
(1254 mm)
49 3/8"
(233 mm)
9 3/16"
(533 mm)
21"
(908 mm)
35 3/4"
4" (102 mm)
OPTIONAL ACCESSORIES
SKSFD3604P
36" INTEGRATED FRENCH
DOOR REFRIGERATOR
Notes
These units are designed to be customized with decorative panels. Field-
installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes
for mounting panel brackets (provided with unit). Adjustment screws and
instructions also provided with units.
Maximum Panel Weight:
A – Fresh food door panels: 33 lbs.
B – Convertible drawer panel: 22 lbs.
C – Freezer drawer panel: 33 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is
recommended that both sides of each cutout panel be nished to match the
cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is
unnished.
Door Handles: Handles are not included with the refrigerator. Custom handles
are required for installation. Brushed Aluminum Handles are available as an
optional accessory.
This refrigerator can be installed with an optional Stainless Steel Panel Kit. Kit includes two
fresh food door panels, one convertible drawer panel, one freezer drawer panel, one toe kick
and four handles.
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
36-INCH BUILT-IN FRENCH DOOR REFRIGERATOR
CUSTOM PANEL DIMENSIONS
These units are designed to be customized with decorative panels. Field- installed
custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for
mounting panel brackets (provided with unit). Adjustment screws and
instructions also provided with units.
Maximum Panel Weight:
A —-Fresh food door panels: 33 |bs.
B - Convertible drawer panel: 22 Ibs.
C - Freezer drawer panel: 33 Ibs.
4" (102 mm) will be visible on the interior sides of the furniture return. It is
recommended that both sides of each cutout panel be finished to match the
cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the refrigerator. Custom handles
are required for installation. Brushed Aluminum Handles are available as an
optional accessory.
OPTIONAL ACCESSORIES
This refrigerator can be installed with an optional Stainless Steel Panel Kit. Kit includes two
fresh food door panels, one convertible drawer panel, one freezer drawer panel, one toe kick
and four handles.
Page 16 of 19 | Effective 6/20 | WCAG
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER
AND
24" REFRIGERATOR COLUMN
24" (610 mm)
min. depth
84"
(2134 mm)
4"
(102 mm)
finished
return*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is
recommended on all sides and the top of the cutout opening. The shaded
area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished
cabinet returns.
*
41 1/2" (1054 mm)
finished width
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER
AND
30" REFRIGERATOR COLUMN
24" (610 mm)
min. depth
84"
(2134 mm)
4"
(102 mm)
finished
return*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on
all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
47 1/2" (1207 mm)
finished width
1 3/8" (35 mm)
2 3/4"
(70 mm)
2 3/4"
(70 mm)
5"
(127 mm)
electrical
location
4" (102 mm)
water location
4" (102 mm)
water location
5"
(127 mm)
electrical
location
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER
AND
24" REFRIGERATOR COLUMN
24" (610 mm)
min. depth
84"
(2134 mm)
4"
(102 mm)
finished
return*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is
recommended on all sides and the top of the cutout opening. The shaded
area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished
cabinet returns.
*
41 1/2" (1054 mm)
finished width
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER
AND
30" REFRIGERATOR COLUMN
24" (610 mm)
min. depth
84"
(2134 mm)
4"
(102 mm)
finished
return*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on
all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
47 1/2" (1207 mm)
finished width
1 3/8" (35 mm)
2 3/4"
(70 mm)
2 3/4"
(70 mm)
5"
(127 mm)
electrical
location
4" (102 mm)
water location
4" (102 mm)
water location
5"
(127 mm)
electrical
location
COLUMN
COLUMN
Notes
The 18" integrated column freezer
has an actual width of 17 1/2" (445
mm) to accommodate a retrot
installation. This will allow you to
combine the 18" freezer column
with a 24" refrigerator column in a
41 1/2" (1054 mm) cutout or with a
30" refrigerator column in a 47 1/2"
(1207 mm) cutout.
Electrical
A minimum 15 amp (115V, 60Hz)
power supply is required for each
individual column. An individual
properly grounded branch circuit
or circuit breaker is recommended.
Install a properly grounded 3-prong
electrical receptacle recessed into
the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter)
is not recommended.
Water Line
A cold water supply is required for
water dispenser and automatic
icemaker operation for each
individual column. Water pressure
must be between 20 and 120 p.s.i.
Tubing should be long enough to
extend to the front of the unit. Allow
enough tubing to accommodate
a bend leading into the water line
connection.
Water line can enter an opening
through oor or back wall.
Install a shut-o valve between the
icemaker water valve and cold water
supply in the home.
INTEGRATED COLUMN
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
The 18" integrated column freezer
has an actual width of 17 1/2" (445
mm) to accommodate a retrofit
installation. This will allow you to
combine the 18" freezer column
with a 24" refrigerator column in a
41 1/2" (1054 mm) cutout or with a
30" refrigerator column in a 47 1/2"
(1207 mm) cutout.
A minimum 15 amp (115V, 60Hz)
power supply is required for each
individual column. An individual
properly grounded branch circuit or
circuit breaker is recommended.
Install a properly grounded 3-prong
electrical receptacle recessed into
the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
A cold water supply is required for water
dispenser and automatic icemaker
operation for each individual column.
Water pressure must be between 20 and
120 p.s.i.
Tubing should be long enough to
extend to the front of the unit. Allow
enough tubing to accommodate a
bend leading into the water line
connection.
Water line can enter an opening through
floor or back wall.
Install a shut-off valve between the
icemaker water valve and cold water
supply in the home.
Page 17 of 19 | Effective 6/20 | WCAG
INTEGRATED COLUMN
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"
(3 mm)
min.
90°
115°
8 3/4"*
(223 mm)
41 1/2" cutout (1054 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
18-INCH INTEGRATED COLUMN FREEZER
AND
24-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.
(3 mm)
23 3/4"
(603 mm)
11 3/8"*
(288 mm)
24"
(610 mm)
25 1/2"
(648 mm)
**
Varies depending on the thickness of the
custom cabinet panel. The door panels in the
optional Signature Kitchen Suite stainless
steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
TOP VIEW
1/8"
(3 mm)
min.
90°
115°
8 3/4"*
(223 mm)
47 1/2" cutout (1207 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
18-INCH INTEGRATED COLUMN FREEZER
AND
30-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.
(3 mm)
29 3/4"
(756 mm)
13 7/8"*
(352 mm)
24"
(610 mm)
32 1/4"
(819 mm)
**
Varies depending on the thickness of the custom cabinet
panel. The door panels in the optional Signature Kitchen
Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"
(3 mm)
min.
90°
115°
8 3/4"*
(223 mm)
41 1/2" cutout (1054 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
18-INCH INTEGRATED COLUMN FREEZER
AND
24-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.
(3 mm)
23 3/4"
(603 mm)
11 3/8"*
(288 mm)
24"
(610 mm)
25 1/2"
(648 mm)
**
Varies depending on the thickness of the
custom cabinet panel. The door panels in the
optional Signature Kitchen Suite stainless
steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
TOP VIEW
1/8"
(3 mm)
min.
90°
115°
8 3/4"*
(223 mm)
47 1/2" cutout (1207 mm)
24"
(610 mm)
20 1/4"
(514 mm)
17 3/4"
(451 mm)
18-INCH INTEGRATED COLUMN FREEZER
AND
30-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.
(3 mm)
29 3/4"
(756 mm)
13 7/8"*
(352 mm)
24"
(610 mm)
32 1/4"
(819 mm)
**
Varies depending on the thickness of the custom cabinet
panel. The door panels in the optional Signature Kitchen
Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"
(19 mm)**
Optional Frame Kit
SKSFK800CS can
be installed for a
finished look.
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
1 1/4"*
(32 mm)
Notes
In retrot installations where the cutout
is only 24" (610 mm) deep, the front face
of the unit extends approximately 3/4" (19
mm) beyond 24" (610 mm) depth adjacent
cabinets for a proud appearance.
The unit can be installed with 3/4" custom
panel or optional stainless steel panel kit.
An optional Frame Kit is recommended for
a nished look.
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER
AND 24-INCH INTEGRATED COLUMN REFRIGERATOR
*Door handle must be added to this dimension.
** Varies depending on the thickness of the custom cabinet
panel. The door panels in the optional Signature Kitchen Suite
stainless steel door panel kit are 3/4" (19 mm) thick.
TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER
AND 30-INCH INTEGRATED COLUMN REFRIGERATOR
*Door handle must be added to this dimension.
** Varies depending on the thickness of the custom cabinet panel. The door
panels in the optional Signature Kitchen Suite stainless steel door panel kit
are 3/4" (19 mm) thick.
In retrofit installations where the cutout is
only 24" (610 mm) deep, the front face of
the unit extends approximately 3/4" (19
mm) beyond 24" (610 mm) depth adjacent
cabinets for a proud appearance.
The unit can be installed with 3/4" custom
panel or optional stainless steel panel kit.
An optional Frame Kit is recommended for
a finished look.
Page 18 of 19 | Effective 6/20 | WCAG
Door Panel
(451 mm)
17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P
24-INCH INTEGRATED COLUMN
REFRIGERATOR
79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
(603 mm)
23 3/4"
Door Panel
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)
Toekick Width
47 1/2" (1207 mm)
Toekick Width
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
(451 mm)
17 3/4"
4" (102 mm)
4" (102 mm)
4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)
23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)
29 3/4"
Door Panel 79 7/8"
(2029 mm)
(603 mm)
23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"
(2029 mm)
Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)
23 3/4"
79 7/8"
(2029 mm)
Door Panel
(451 mm)
17 3/4"
(756 mm)
29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
Notes
These units are designed to be customized with
decorative panels. Field-installed custom door panels or
an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to
pre-drill holes for mounting panel brackets (provided with
unit). Adjustment screws and instructions also provided
with units.
Maximum Total Door Panel Weights:
30-Inch Integrated Column – 64 lbs.
24-Inch Integrated Column – 53 lbs.
18-Inch Integrated Column – 44 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the
furniture return. It is recommended that both sides of each
cutout panel be nished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The
bottom of case
is unnished.
In retrot installations where the cutout is 24" (610 mm)
deep, the optional Frame Kit is recommended to provide a
nished look.
Door Handles: Handles are not included with the units.
Custom handles are required for installation. Brushed
Aluminum Handles are available as an optional accessory.
INTEGRATED COLUMN
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
DUAL 18-INCH AND 24-INCH
INTEGRATED COLUMNS
DUAL 18-INCH AND 30-INCH
INTEGRATED COLUMNS
Maximum Total Door Panel Weights:
30-Inch Integrated Column – 64 lbs.
24-Inch Integrated Column – 53 lbs.
18-Inch Inteqgrated Column = 44 |bs.
OPTIONAL ACCESSORIES – RETROFIT INSTALLATION
All units can be installed in a 24" (610 mm) deep cutout with an optional frame kit. This kit includes
two 80" (2032 mm) brushed aluminum side trim pieces. Each trim piece is 5" (127 mm) deep with a
1/8" (3 mm) front face.
This kit is required for installation when a wine column is installed with another wine column,
refrigerator column or French door column. This kit is included with all freezer columns.
Design Tips
The Stainless Steel Panel Kit may be used in a retrot 24" (610 mm) cutout depth installation.
For retrot / replacement installations where the existing cutout is 24" (610 mm) deep, the optional
frame kit is recommended.
© 2020 Signature Kitchen Suite. All rights reserved. Design, features and specications are subject to change without notice. Specications are for planning purposes only. Consult
the product’s installation instructions for nal dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your
specic ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access.
1-855-790-6655 | www.signaturekitchensuite.com
Effective 6/20 | WCAG
INTEGRATED COLUMN
OPTIONAL ACCESSORIES – RETROFIT INSTALLATION
All units can be installed in a 24" (610 mm) deep cutout with an optional frame kit. This kit includes
two 80" (2032 mm) brushed aluminum side trim pieces. Each trim piece is 5" (127 mm) deep with a
1/8" (3 mm) front face.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Signature Kitchen Suite SKSCW181RP User guide
- Category
- Fridges
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Sub-Zero 601F Design Manual
-
Gaggenau 395 User manual
-
Sub-Zero 5310891 User guide
-
Wolf I700BR User manual
-
Sub-Zero 5310751 User guide
-
Thermador T30BB810SS Download Design Guide
-
-
Sub-Zero IT-30CIID User guide
-
-