Casio XJ-42 User manual

DATA PROJECTOR

XJ-A141/XJ-A146*

XJ-A241/XJ-A246*

XJ-A251/XJ-A256*

User’s Guide

zBe sure to read the precautions in the separate Setup Guide.

zBe sure to keep all user documentation handy for future

reference.

E

* USB Port Models

2

zDLP is a registered trademark of Texas Instruments of the United States.

zMicrosoft, Windows, and Windows Vista are registered trademarks or trademarks of Microsoft

Corporation in the United States and other countries.

zHDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing, LLC.

zXGA is a registered trademark of IBM Corporation of the United States.

zOther company and product names may be registered product names or trademarks of their

respective owners.

zPortions of this product are based in part on the work of the Independent JPEG Group.

zThe contents of this User’s Guide are subject to change without notice.

zCopying of this manual, either in part or its entirety is forbidden. You are allowed to use this

manual for your own personal use. Any other use is forbidden without the permission of CASIO

COMPUTER CO., LTD.

zCASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or claims from third

parties arising out of the use of this product or this manual.

zCASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to loss of

data due to malfunction or maintenance of this product, or any other reason.

zThe sample screens shown in this manual are for illustrative purposes only, and may not be

exactly the same as the screens actually produced by the product.

3

Contents

About this manual... ...............................................................................5

Projector Overview ......................................................... 6

Projector Features and Main Functions .................................................6

Remote Controller and Projector Keys...................................................8

Back Terminals.......................................................................................9

Loading Remote Controller Batteries.....................................................9

Setting Up the Projector.......................................................................10

Setup Precautions ................................................................................10

Connecting to an Image Output Device...................... 11

Connecting the Analog RGB Output of a

Computer to the Projector....................................................................11

Connecting the HDMI Output of a Video Device or

Computer to the Projector....................................................................12

Connecting to a Video Device..............................................................13

Connection to a composite video output .................................................................. 13

Connection to a component video output................................................................. 13

Operation During Projection ........................................ 14

Selecting the Input Source ...................................................................14

To select a different input source .............................................................................. 14

Resolution .................................................................................................................. 14

Image Operations During Projection ....................................................15

Adjusting Image Brightness....................................................................................... 15

To use manual keystone correction........................................................................... 15

Selecting the Color Mode .......................................................................................... 16

Zooming an Image..................................................................................................... 16

Momentarily Blanking the Image and Muting the Audio............................................ 17

Freezing an Image...................................................................................................... 17

Displaying a Pointer in the Projected Image.............................................................. 18

Changing the Aspect Ratio of the Projected Image .................................................. 19

Adjusting the Volume Level..................................................................20

To adjust the volume level ......................................................................................... 20

To mute the audio...................................................................................................... 20

B

4

Presentation Timer ...............................................................................21

Eco Mode (Power Saving, Low Noise) .................................................23

To select the Eco Mode............................................................................................. 23

Using the [FUNC] Key ..........................................................................24

Configuring Advanced Projector Settings .................. 25

Basic Setup Menu Operations .............................................................25

Displaying the Setup Menu........................................................................................ 25

Configuring Setup Menu Settings.............................................................................. 25

Basic Setup Menu Example....................................................................................... 26

Direct Power On......................................................................................................... 27

Password Protecting the Projector ......................................................28

Inputting a Password................................................................................................. 28

Using the Password Feature...................................................................................... 28

Entering the Password when Turning On the Projector ............................................ 30

Restoring Projector Settings to Their Initial Factory Defaults ..............31

Setup Menu Contents ..........................................................................33

Image Adjustment 1 Main Menu................................................................................ 33

Image Adjustment 2 Main Menu................................................................................ 35

Volume Adjustment Main Menu................................................................................. 35

Screen Settings Main Menu....................................................................................... 36

Input Settings Main Menu.......................................................................................... 38

Option Settings 1 Main Menu .................................................................................... 39

Option Settings 2 Main Menu .................................................................................... 40

USB Settings Main Menu (USB Port Models Only) ................................................... 42

Wireless Main Menu (USB Port Models Only) ........................................................... 42

Operational Info Main Menu ...................................................................................... 42

Restore All Defaults Main Menu................................................................................. 42

Cleaning the Projector.................................................. 43

Cleaning the Projector Exterior ............................................................43

Cleaning the Lens.................................................................................43

Cleaning Intake and Exhaust Vents......................................................43

Troubleshooting ............................................................ 44

Indicators..............................................................................................44

Error Indicators and Warning Messages ..............................................44

5

Projector Troubleshooting....................................................................47

Appendix ........................................................................ 49

Remote Controller Signal Range..........................................................49

Projection Distance and Screen Size ...................................................50

Aspect Ratio Setting and Projection Image .........................................51

Supported Signals................................................................................53

Specifications.......................................................................................55

All of the operations in this manual are explained using the remote controller that comes with the

projector.

About this manual...

6

Projector Overview

This section describes the features of the projector, and explains the functions of the projector and

remote controller keys.

XJ-A141/XJ-A146/XJ-A241/XJ-A246/XJ-A251/XJ-A256

zMercury-free Hybrid Light Source:

A CASIO-original laser and LED hybrid light source delivers high luminance from 2,500 to

3,000 lumens. This projector does not use a mercury lamp, making it environmentally friendly.

zSlim and compact:

A4 file size and approximately 43 mm slim. Compact enough to install or use just about anywhere.

zHDMI video/audio input:

HDMI (High Definition Multimedia Interface) input support enables direct connectivity with today’s

HDMI enabled notebook PCs, high-definition video devices (BD, HD DVD, DVD players, etc.), and

games. The projector supports image projection and audio output from these devices.

zWide projection range:

A wide angle 2X zoom allows projection even when projector-to-screen distance is severely limited.

When using a projection size of 60 inches, projection can be performed from a distance of

1.4 meters (XJ-A241/XJ-A246/XJ-A251/XJ-A256) or 1.7 meters (XJ-A141/XJ-A146).

zA wide selection of input sources:

Analog RGB, composite video, component video (Y·Cb·Cr, Y·Pb·Pr), and HDMI input sources are

supported.

zIntelligent Brightness Control function (Eco Mode):

The projector senses surrounding light levels and adjusts projection brightness automatically as

required for efficient low-power operation. (Requires “Eco Mode” setting to be set to “On (Auto)”.)

zPointer:

The remote controller can be used to select one of a variety of different pointers for use during

projection.

zDirect Power On:

The projector can be configured to turn on automatically and start projecting as soon as it is

plugged into a power outlet.

Projector Features and Main Functions

7

XJ-A241/XJ-A246/XJ-A251/XJ-A256

zWXGA Resolution:

The XJ-A241/XJ-A246/XJ-A251/XJ-A256 models support WXGA (1280 × 800) resolution for optimal

viewing of content formatted for today’s widescreen displays. This makes it perfect for projecting

images from widescreen notebook PCs and HD video input sources.

XJ-A146/XJ-A246/XJ-A256

zProjection of Data from USB Memory or a Memory Card without a Computer:

USB memory or a memory card (using a commercially available USB card reader) can be connected

directly to the projector’s USB port. The projector comes with special software for converting

PowerPoint presentation data to a format that can be stored to USB memory or a memory card and

projected without using a computer. Images and movies also can be projected directly from USB

memory or a memory card.

zMulti Projection Camera (YC-400, YC-430) Connection:

A CASIO Multi Projection Camera can be connected directly to the projector’s USB port for fine

resolution projection of documents and other images. Document camera capabilities allow

projection of data without going through a computer.

zGraphic Scientific Function Calculator Connection:

Certain CASIO graphic scientific calculator models can be connected directly to the projector’s

USB port for projection of the calculator screen contents.

zProjection of Computer Screen Contents via Wireless LAN:

The projector comes with a wireless LAN adapter. After a wireless LAN connection is established,

the contents of the computer screen can be sent to the projector for projection.

zSupport for Wireless projection from MobiShow:

You can install AWIND’s MobiShow (client software for wireless connection to a projector) on a

smartphone or mobile terminal, and then use the projector to project photographs and presentation

files stored in the smartphone or terminal memory.

*Note that the type of terminal and the MobiShow version can limit certain functions or can even

make projection impossible.

8

Operations in this manual are presented based on the remote controller that comes with the projector.

Major operation keys are also provided on the projector unit, so the most of the same procedures can

also be performed directly on the projector.

Remote Controller Keys

The remote controller does not come with batteries loaded. You need to load the two supplied

batteries before use.

Important!

To avoid running down the batteries, store the remote control unit so its keys are not pressed

inadvertently.

Projector Keys and Indicators

Remote Controller and Projector Keys

Remote control signal emitter

CLASS 1 LED PRODUCT

Cursor keys (S/T/W/X)

[ENTER] key ([STYLE] key)

[D-ZOOM +] [D-ZOOM –] keys

[KEYSTONE +] [KEYSTONE –] keys

[POINTER] key

[FUNC] key

[AUTO] key

[BLANK] key

[FREEZE] key

[COLOR MODE] key

[VOLUME] key

[BRIGHT] key ([O] key)

[ECO] key ([f] key)

[ASPECT] key ([Z] key)

[INPUT] key

[MENU] key

[ZOOM +] [ZOOM –] keys

[FOCUS S] [FOCUS T] keys

[P] (Power) key

[TIMER] key

[ESC] key

TEMP indicator [FOCUS] key

LIGHT indicator [ENTER] key

POWER/STANDBY indicator [MENU] key

[P] (Power) key

[ESC] key

[INPUT] key

Cursor keys (q/w/U/I)

[AUTO] key

[ZOOM] key

9

Depending on your projector, the orientation of the ports and terminals may be opposite from those

shown in the illustration below. Functions and use of the ports and terminals are the same as

described in this manual, regardless of their orientation.

*This serial port is for connecting a separately available special cable (YK-5) to control the projector

from a computer.

Important!

Be sure to use alkaline batteries only.

Replacing Remote Controller Batteries

Open the battery cover on the back of the remote controller, replace the old batteries with new ones,

and then close the battery cover.

Back Terminals

Loading Remote Controller Batteries

*Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

1.

Open the battery cover on the back

of the remote controller.

2.

Load two new batteries into the

case, making sure that their positive

(+) and negative (–) ends are facing

correctly.

3.

Close the battery cover on the back of the remote controller.

Serial port*

COMPUTER terminal

USB port

(XJ-A146/XJ-A246/XJ-A256 only)

Power connector

Anti-theft lock hole

Intake vents

AV terminal

HDMI port

Speaker

Remote control signal receiver

C

10

Locate the projector on a desk, table, or stand that is firm and level. Make sure that you allow

sufficient space around the sides and back of the projector for proper ventilation. The following

illustrations show how the projector should be oriented for optimum projection relative to the screen.

zThe projector can be configured for projection from the back of a screen. For details, see

“Projection Mode” (page 37) under “Screen Settings Main Menu”.

zUse a conveniently located power outlet that you can reach easily when you need to unplug the

projector.

zDo not allow any objects to be within the area indicated by the dashed line below, which is an area

within 30cm (11.8 inches) of the projector. Keep all obstacles and other objects at least 30cm away

from the projector’s vents.

zAirflow from air conditioning equipment can blow the heat being exhausted from the area around

the projector’s lens in a way that causes heat ripples to appear in the projected image. If this

happens, adjust the airflow of the air conditioning equipment or move the projector.

Setting Up the Projector

XJ-A141/XJ-A146 XJ-A241/XJ-A246/XJ-A251/XJ-A256

Make sure the projector is at a right angle to the screen. Position the projector so the lens side is at the edge of the table,

etc.

Setup Precautions

Screen Screen

Intake vents

Exhaust vents

30cm

(11.8 inches)

Intake vents

11

Connecting to an Image Output Device

Connect the projector’s COMPUTER terminal to the RGB terminal of a computer as shown in the

illustration below.

Important!

zAlways turn off the projector and the computer before connecting them.

zTake care so the volume level of the computer is not set too high.

Connecting the Analog RGB Output of a Computer to

the Projector

Bundled mini D-Sub cable

Audio cable (commercially available)

AV terminal

To monitor terminal

(analog RGB output terminal)

COMPUTER terminal

To line output terminal

Projector Computer

12

The projector supports projection and output of HDMI video and audio output from a computer or

video device.

Important!

Turn off the projector and the computer or video device before connecting them.

zYou will need to obtain a commercially available HDMI cable with a connector that matches the

terminal of the output device on one end and a connector that matches the projector’s HDMI port

(HDMI Type A Socket) on the other end.

zFor information about HDMI video signal supported by the projector, see page 54.

zThe projector supports L-PCM 32kHz, 44.1kHz, and 48kHz HDMI audio signals.

Connecting the HDMI Output of a Video Device or

Computer to the Projector

Projector

HDMI port

To HDMI output terminal

Computer or video device

HDMI cable (commercially available)

13

The projector is able to project images from the composite video output or component video output of

a connected video device.

Important!

Always turn off the projector and the video device before connecting them.

Connection to a composite video output

zYou can use the bundled special AV cable to connect to a pin jack (RCA) type video output terminal.

When connecting a video camera or other video device with a special video output terminal, use the

special cable that comes with the video device. For details, see the documentation that comes with

the video device.

Connection to a component video output

zComponent video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match

the colors of the plugs on a component video cable with the colors of the terminals (Green: Y;

Blue: Cb/Pb; Red: Cr/Pr).

zNote that connection only to an analog component video output terminal is supported.

Connection to a digital output terminal is not supported.

Connecting to a Video Device

Video device

Bundled special AV cable

Projector

Yellow Red

To video output

terminal

To audio output

terminals

White

AV terminal

Projector

COMPUTER terminal

AV terminal

Bundled special AV cable

Component video cable (commercially available)

To component video

output terminals

To audio output

terminals

Video device

Yellow

(Not connected)

Red

White

14

Operation During Projection

Turning on the projector initially causes the same input source that was selected the last time it was

turned off to be selected.

To select a different input source

1.

Press the [INPUT] key.

zThis displays the input source selection screen.

2.

Use the [T] and [S] keys to select the name of the input source you want to

select and then press the [ENTER] key.

zThe name of the input source you select appears in the upper right corner of the projection

screen for a few seconds.

zThe message “No signal input.” will appear if no input signal can be selected.

Resolution

Depending on the projector model, its video resolution will be fixed at XGA (1024 × 768 pixels) or

WXGA (1280 × 800 pixels). Images may appear coarse, text and other figures may be difficult to read

or a moire pattern may appear when the input signal from a computer does not match the projector’s

video resolution. If this happens, try doing the following.

zChange the computer’s output resolution setting so it matches the projector’s video resolution.

For information about the video resolution of your projector, see the “DLP chip” item of the

“Specifications” (page 55). See the user documentation that comes with your computer for details

about changing its settings.

zChange the “Aspect Ratio” setting to “True” (Applies only to models that support WXGA video

resolution).

With the “True” setting, the projector projects the input signal at its actual size (1 input source dot

equal to one projector output pixel dot).

For information about configuring the Aspect Ratio setting, see “Changing the Aspect Ratio of the

Projected Image” (page 19).

Selecting the Input Source

15

You can perform the following operations while projecting an image.

zImage brightness adjustment

zManual keystone correction

zColor mode selection

zImage zooming

zMomentarily blanking the image and muting the audio

zImage freeze

zPointer display in the projected image

zAspect ratio switching

Adjusting Image Brightness

Note

(for USB port model users)

Use the setup menu (page 25) to adjust image brightness when the input source is an external

device connected to the USB port or via the wireless adapter.

1.

Press the [BRIGHT] key.

zThis displays the brightness adjustment window.

2.

Use the [W] and [X] keys to adjust image brightness.

3.

To hide the window, press the [ESC] key.

To use manual keystone correction

The projector has a keystone correction feature that prevents

distortion of the projected image when projecting from an

angle. The projector detects when it is at a vertical angle to the

screen and performs keystone correction automatically.

You can use the [KEYSTONE +] and [KEYSTONE –] keys to

adjust keystone correction manually.

Image Operations During Projection

B

16

Selecting the Color Mode

You can select from among various different color mode settings in accordance with image contents

and projection conditions.

Important!

The color mode cannot be selected in the following cases.

zWhen “Off” is selected for the Eco Mode setting (page 23)

To change the color mode

1.

Press the [COLOR MODE] key.

zThis displays the color mode selection window. The currently selected color mode is the one

whose button is selected (filled in).

2.

Use the [T] and [S] keys to move the highlighting to the color mode you want to

select, and then press the [ENTER] key.

zThis will select the button next to the highlighted color mode name.

zFor details on what each color mode does, see “Color Mode” (page 34) under “Image

Adjustment 1 Main Menu”.

3.

To hide the window, press the [ESC] key.

Zooming an Image

1.

Press the [D-ZOOM +] key.

zThis will enlarge the center of the projected image one step.

2.

To zoom in on the center of the projected image more, press the [D-ZOOM +]

key again. To zoom out, press the [D-ZOOM –] key.

zEach press of [D-ZOOM +] zooms in (increases the zoom factor), while [D-ZOOM –] zooms

out. Holding down either key continuously scrolls the zoom factor.

3.

While an image is zoomed, use the [S], [T], [W], and [X] keys to scroll the view

to other parts of the image.

4.

To exit the zoom operation, press the [ESC] key.

17

Momentarily Blanking the Image and Muting the Audio

1.

Press the [BLANK] key.

zThis temporarily blanks the image (projecting a black screen) and mutes the audio.

2.

To resume normal image and sound, press the [BLANK] key (or [ESC] key).

Note

You can specify projection of a black screen or blue screen, or a logo. For details, see “Blank

Screen” (page 37) under “Screen Settings Main Menu”.

Freezing an Image

Pressing the [FREEZE] key freezes the projected image.

To freeze the projected image

1.

While an image is being projected from an input source, press the [FREEZE] key.

zThis will capture the image that is on the screen at the moment you press [FREEZE] and stores

it in projector memory. That image remains projected on the screen.

2.

To restore projection of the image from an input source, press the [ESC] key.

B

18

Displaying a Pointer in the Projected Image

You can select from among different pointer styles, including various arrow styles, for display in the

projected image. Pointers can be used during a presentation to indicate or highlight a specific part of

the image.

Note

Depending on the pointer style you are using, the pointer may not display properly when you are

using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to

change the keystone correction value to zero.

To display a pointer in the image

1.

Press the [POINTER] key.

zThis will cause a pointer to appear in the image.

zYou also can use the setup menu to specify the pointer type that appears first when you press

the [POINTER] key. For details, see “Pointer” (page 40) under “Option Settings 2 Main Menu”.

2.

Use the cursor keys to move the pointer to the location you want.

zHolding down a cursor key moves the cursor at high speed.

3.

To modify the pointer as described below, press the [STYLE] key.

To select the pointer type

1.

Press the [POINTER] key to display the pointer.

2.

Keep pressing the [POINTER] key until the pointer you want is displayed.

zEach press of the [POINTER] key cycles through the available pointer types.

To clear the pointer from the image

Press the [ESC] key.

For this pointer type: Pressing [STYLE] will change it like this:

J J J

Toggle between flashing and not flashing

19

Changing the Aspect Ratio of the Projected Image

Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.

Available settings depend on your projector model as shown below. For details about the meaning of

each setting, see “Aspect Ratio” (page 36) under “Screen Settings Main Menu”.

XJ-A241/XJ-A246/XJ-A251/XJ-A256

Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as

shown below.

XJ-A141/XJ-A146

Pressing the [ASPECT] key will toggle between settings in accordance with the current input source as

shown below.

Note

zFor details about how the aspect ratio setting affects the projected image, see “Aspect Ratio

Setting and Projection Image” (page 51).

zYou also can change the aspect ratio setting using the setup menu. For details, see “Aspect

Ratio” (page 36) under “Screen Settings Main Menu”.

Important!

Note that enlarging or reducing the size of an image using the [ASPECT] key for commercial

purposes or public presentation may infringe on the legally protected copyright of the copyright

holder of the original material.

Input Source Pressing [ASPECT] will cycle through these settings:

Video, Component, HDMI (DTV) Normal J 16:9 J 4:3 J Letter Box

RGB, HDMI (PC) Normal J Full J 4:3 J True

Input Source Pressing [ASPECT] will toggle between these settings:

Video, Component, HDMI (DTV) Normal



16:9

RGB, HDMI (PC) Normal



Full

B

20

You can use the remote controller keys to adjust the volume level of the audio that is output from the

projector’s speaker or the AV terminal.

To adjust the volume level

1.

Press the [VOLUME] key.

zThis causes the [Volume] screen to appear on the projected image.

2.

Press the [X] key to increase the volume, or the [W] key to lower the volume.

3.

After the setting is the way you want, press the [ESC] key.

zThis causes the [Volume] screen to disappear.

Note

You also can use the setup menu to adjust the volume level. For details, see “Volume

Adjustment Main Menu” on page 35.

To mute the audio

1.

Press the [VOLUME] key.

2.

Press the [ENTER] key.

zThis stops output from the speaker.

3.

To restore the audio, press the [VOLUME] key again.

Adjusting the Volume Level

B

Page is loading ...

Casio XJ-42 User manual

Related papers

Other documents