Pepperl+Fuchs FB3205B3 User manual

Brand: Pepperl+Fuchs

Model: FB3205B3

Type: User manual

Instruction Manual

1. Marking

(HART)TransmitterPowerSupply,InputIsolatorFB3205B3

ATEXcertificate:Presafe19ATEX14056U

ATEXmarking:

1II2(1)GExdbebq[iaGa]IICGb

II(1)D[ExiaDa]IIIC

I(M1)[ExiaMa]I

IECExcertificate:IECExPRE19.0011U

IECExmarking:

Exdbebq[iaGa]IICGb

[ExiaDa]IIIC

[ExiaMa]I

Pepperl+FuchsGroup

Lilienthalstraße200,68307Mannheim,Germany

Internet:www.pepperl-fuchs.com

2. Validity

Specificprocessesandinstructionsinthisinstructionmanualrequire

specialprovisionstoguaranteethesafetyoftheoperatingpersonnel.

3. Target Group, Personnel

Responsibilityforplanning,assembly,commissioning,operation,

maintenance,anddismountinglieswiththeplantoperator.

Thepersonnelmustbeappropriatelytrainedandqualifiedinordertocarry

outmounting,installation,commissioning,operation,maintenance,and

dismountingofthedevice.Thetrainedandqualifiedpersonnelmusthave

readandunderstoodtheinstructionmanual.

Priortousingtheproductmakeyourselffamiliarwithit.Readthe

instructionmanualcarefully.

4. Reference to Further Documentation

Observedirectives,standards,andnationallawsapplicable

totheintendeduseandtheoperatinglocation.

ObserveDirective1999/92/ECinrelationtohazardousareas.

Observedirectives,standards,andnationallawsapplicabletothe

intendeduseandtheoperatinglocation.

Thecorrespondingdatasheets,manuals,declarationsofconformity,EU-

typeexaminationcertificates,certificates,andcontroldrawings

ifapplicable(seedatasheet)areanintegralpartofthisdocument.Youcan

findthisinformationunderwww.pepperl-fuchs.com.

Forspecificdeviceinformationsuchastheyearofconstruction,

scantheQRcodeonthedevice.Asanalternative,entertheserialnumber

intheserialnumbersearchatwww.pepperl-fuchs.com.

Duetoconstantrevisions,documentationissubjecttopermanentchange.

Pleasereferonlytothemostup-to-dateversion,whichcanbefoundunder

www.pepperl-fuchs.com.

5. Intended Use

Thedeviceisonlyapprovedforappropriateandintendeduse.

Ignoringtheseinstructionswillvoidanywarrantyandabsolve

themanufacturerfromanyliability.

Usethedeviceonlywithinthespecifiedambienttemperaturerange.

Usethedeviceonlywithinthespecifiedambientandoperatingconditions.

Onlyusethedevicestationary.

ThedeviceisanassociatedapparatusaccordingtoIEC/EN60079-11.

TheI/Omodules,comunits,powersupplies,andbusterminationmodules

oftheremoteI/Osystemmustonlybeusedtogetherwiththeassociated

backplanes.

Thebackplaneconnectionsarenon-intrinsicallysafe.

TheI/OmodulesoftheremoteI/Osystemactasaninterfacebetween

signalsfromthehazardousareaandthenon-hazardousarea.

6. Improper Use

Protectionofthepersonnelandtheplantisnotensuredifthedevice

isnotusedaccordingtoitsintendeduse.

Thedeviceisnotsuitableforisolatingsignalsinpowerinstallationsunless

thisisnotedseparatelyinthecorrespondingdatasheet.

7. Mounting and Installation

Priortomounting,installation,andcommissioningofthedeviceyou

shouldmakeyourselffamiliarwiththedeviceandcarefullyreadthe

instructionmanual.

Observetheinstructionmanualsfortheassociatedbackplanes.

Thedevicemustonlybeoperatedinthespecifiedambienttemperature

rangeandatthespecifiedrelativehumiditywithoutcondensation.

Donotmountthedeviceatlocationswhereanaggressiveatmosphere

maybepresent.

Thedevicemustbeinstalledandoperatedonlyinacontrolled

environmentthatensuresapollutiondegree2(orbetter)accordingto

IEC/EN60664-1.

Thedevicemustbeinstalledandoperatedonlyinanenvironmentof

overvoltagecategoryII(orbetter)accordingtoIEC/EN60664-1.

Thepermittedsupplyshort-circuitcurrentforthecomponentsis50A.

Avoidelectrostaticchargeswhichcouldresultinelectrostaticdischarges

whileinstalling,operating,ormaintainingthedevice.

Ifthedevicehasalreadybeenoperatedingeneralelectricalinstallations,

thedevicemaysubsequentlynolongerbeinstalledinelectrical

installationsusedincombinationwithhazardousareas.

Donotmountadamagedorpolluteddevice.

Onlyuseaccessoriesspecifiedbythemanufacturer.

Pushthemoduleintotheslotuntilallrearcatcheshaveaudiblyengaged

inposition.Themodulemustengagetwice.

Donotpushthemodulesintotheslotswithtoomuchforce.Therear

connectionsofthedevicesmaybedamagedifusingexcessiveforce.In

thiscasetheexplosionprotectioncannolongerbeensured.

Thedevicemustbeinstalledandoperatedonlyinsurroundingenclosures

that

lcomplywiththerequirementsforsurroundingenclosuresaccordingto

IEC/EN60079-0,

lareratedwiththedegreeofprotectionIP54accordingto

IEC/EN60529.

ObservetheinstallationinstructionsaccordingtoIEC/EN60079-14.

ThedevicemayonlybeinstalledandoperatedinZone1ifmountedina

surroundingenclosure,whichcorrespondstoequipmentprotection

levelGb.

Ifintrinsicallysafeandnon-intrinsicallysafecircuitsarebeingoperated

together,theconnectionsofthenon-intrinsicallysafecircuitsmustbe

covered.ThecovermustcomplywithdegreeofprotectionIP30according

toIEC/EN60529.

Afieldcircuitmustnothaveapermanentshortcircuit.Eliminatetheshort

circuit.

Requirements for Cables and Connection Lines

Connectadevicewithwireendsorcabletailonlytoterminalswithtypeof

protectionExe.

Observethepermissiblecorecrosssectionoftheconductor.

Observetheinsulationstrippinglength.

Wheninstallingtheconductorstheinsulationmustreach

uptotheterminal.

Whenusingstrandedconductors,crimpwireendferrules

ontheconductorends.

Neverpullthecable.Awirecouldbecomeloosefromtheterminaland

protectionagainstelectricshockcannolongerbeensured.Alwayspull

theterminal.

Unusedcablesandconnectionlinesmustbeeitherconnectedtoterminals

orsecurelytieddownandisolated.

Requirements for Usage as Associated Apparatus

IfcircuitswithtypeofprotectionExiareoperatedwithnon-intrinsically

safecircuits,theymustnolongerbeusedascircuitswithtypeof

protectionExi.

Intrinsicallysafecircuitsofassociatedapparatus(installedinnon-

hazardousarea)canbeledintohazardousareas.Observethe

complianceoftheseparationdistancestoallnon-intrinsicallysafecircuits

accordingtoIEC/EN60079-14.

Observethecomplianceoftheseparationdistancesbetweentwo

adjacentintrinsicallysafecircuitsaccordingtoIEC/EN60079-14.

Observethemaximumvaluesofthedevice,whenconnectingthedevice

tointrinsicallysafeapparatus.

Observetherespectivepeakvaluesofthefielddeviceandtheassociated

apparatuswithregardtoexplosionprotectionwhenconnectingintrinsically

safefielddeviceswithintrinsicallysafecircuitsofassociatedapparatus

(verificationofintrinsicsafety).AlsoobserveIEC/EN60079-14and

IEC/EN60079-25.

Ifmorechannelsofonedeviceareconnectedinparallel,ensurethe

parallelconnectionismadedirectlyattheterminalsofthedevice.When

verifyingtheintrinsicsafety,observethemaximumvaluesfortheparallel

connection.

IfnoLoandCovaluesarespecifiedforthesimultaneousappearanceof

lumpedinductancesandcapacitances,thefollowingruleapplies.

lThespecifiedvalueforLoandCoisusedifoneofthefollowing

conditionsapplies:

lThecircuithasdistributedinductancesandcapacitancesonly,e.g.,

incablesandconnectionlines.

lThetotalvalueofLi(excludingcable)ofthecircuitis<1%ofthe

specifiedLovalue.

lThetotalvalueofCi(excludingcable)ofthecircuitis<1%ofthe

specifiedCovalue.

DOCT-9129/2024-01 1/2

lAmaximumof50%ofthespecifiedvalueforLoandCoisusedifthe

followingconditionapplies:

ThetotalvalueofLi(excludingcable)ofthecircuitis≥1%ofthe

specifiedLovalue.

ThetotalvalueofCi(excludingcable)ofthecircuitis≥1%ofthe

specifiedCovalue.

lThereducedcapacitanceforgasgroupsI,IIA,andIIBmustnotexceed

thevalueof1µF(includingcable).Thereducedcapacitancefor

gasgroupIICmustnotexceedthevalueof600nF(includingcable).

Requirements for Surrounding Enclosures

Placewarningmarking"Warning–Refertoinstructionmanuals!"visiblyon

thesurroundingenclosure.

Placewarningmarking"Warning–Non-intrinsicallysafecircuitsprotected

byinternalcoverwithadegreeofprotectionIP30!"visiblyonthe

surroundingenclosure.

Placewarningmarking"Warning–Avoidelectrostaticcharge!"visiblyon

thesurroundingenclosure.

Avoidelectrostaticchargeswhichcouldresultinelectrostaticdischarges

whileinstalling,operating,ormaintainingthedevice.

Thesurroundingenclosuremaybeopenedformaintenancewhile

energizedinZone1providedthatthefollowingconditionsaremet:

lTheconnectionsofthenon-intrinsicallysafecircuitsmustbeprotected

byacoverwithadegreeofprotectionIP30.

lAllotherdevicesinthesurroundingenclosuremustpermittheopening

ofthesurroundingenclosurewhileenergizedinZone1.

lAnappropriatemarkingisplacedonthesurroundingenclosure.

8. Operation, Maintenance, Repair

Priortousingtheproductmakeyourselffamiliarwithit.Readthe

instructionmanualcarefully.

Donotuseadamagedorpolluteddevice.

Onlyuseaccessoriesspecifiedbythemanufacturer.

Donotrepair,modify,ormanipulatethedevice.

Substitutionofcomponentsmayimpairintrinsicsafety.

Ifthereisadefect,alwaysreplacethedevicewithanoriginaldevice.

Onlyremovethedevicewiththeintegratedremovalsystem.The

integratedremovalsystemrequiresatwo-stepremovalprocess.

1. Unlockandwait(refertotableforwaittime)

2. Remove

Waittime Device

6s I/OmodulesFB*20*,FB*21*

Pushthemoduleintotheslotuntilallrearcatcheshaveaudiblyengaged

inposition.Themodulemustengagetwice.

Donotpushthemodulesintotheslotswithtoomuchforce.Therear

connectionsofthedevicesmaybedamagedifusingexcessiveforce.In

thiscasetheexplosionprotectioncannolongerbeensured.

ObserveIEC/EN60079-17formaintenanceandinspectionofassociated

apparatus.

Thesurroundingenclosuremaybeopenedformaintenancewhile

energizedinZone1providedthatthefollowingconditionsaremet:

lTheconnectionsofthenon-intrinsicallysafecircuitsmustbeprotected

byacoverwithadegreeofprotectionIP30.

lAllotherdevicesinthesurroundingenclosuremustpermittheopening

ofthesurroundingenclosurewhileenergizedinZone1.

lAnappropriatemarkingisplacedonthesurroundingenclosure.

ExceptforFBmoduleswithfrontsideExeconnections,all

FBI/Omodules,FBpowersupplies,FBbusterminationmodules,and

FBcomunitsmaybeswappedinZone1whileenergized(hotswap).

Protecttheboostercablewithatypeofprotectionaccording

toIEC/EN60079-0,whichcorrespondstotherequiredequipment

protectionlevel.

Afieldcircuitmustnothaveapermanentshortcircuit.Eliminatetheshort

circuit.

Requirements for Cables and Connection Lines

Observethepermissiblecorecrosssectionoftheconductor.

Observetheinsulationstrippinglength.

Wheninstallingtheconductorstheinsulationmustreach

uptotheterminal.

Whenusingstrandedconductors,crimpwireendferrules

ontheconductorends.

Neverpullthecable.Awirecouldbecomeloosefromtheterminaland

protectionagainstelectricshockcannolongerbeensured.Alwayspull

theterminal.

Unusedcablesandconnectionlinesmustbeeitherconnectedtoterminals

orsecurelytieddownandisolated.

9. Delivery, Transport, Disposal

Checkthepackagingandcontentsfordamage.

Checkifyouhavereceivedeveryitemandiftheitemsreceivedarethe

onesyouordered.

Keeptheoriginalpackaging.Alwaysstoreandtransportthedeviceinthe

originalpackaging.

Storethedeviceinacleananddryenvironment.Thepermittedambient

conditionsmustbeconsidered,seedatasheet.

Thedevice,built-incomponents,packaging,andanybatteries

containedwithinmustbedisposedincompliancewiththeapplicablelaws

andguidelinesoftherespectivecountry.

DOCT-9129/2024-01 2/2

Pepperl+Fuchs FB3205B3 User manual

Pepperl+Fuchs FB3205B3 User manual

Pepperl+Fuchs FB3205B3 User manual

Related papers