Hadco S8 Low Voltage Mounting Stake Operating instructions

Hadco
Brand
Hadco
Model
S8 Low Voltage Mounting Stake
Type
Operating instructions

This manual is also suitable for

Hadco S8 Low Voltage Mounting Stake is designed for mounting low voltage fixtures outdoors, in accordance with the National Electrical Code and local code specifications. It is suitable for use in soft or hard soil, and can be installed without excavating the soil in soft soil conditions. The stake has a wire-way slot in the cap for easy fixture wire routing, and the fixture locknut secures the fixture to the top of the cap. The stake is for use with low voltage fixtures only.

Here are some of the key features and benefits of the Hadco S8 Low Voltage Mounting Stake:

  • Easy installation in soft or hard soil

Hadco S8 Low Voltage Mounting Stake is designed for mounting low voltage fixtures outdoors, in accordance with the National Electrical Code and local code specifications. It is suitable for use in soft or hard soil, and can be installed without excavating the soil in soft soil conditions. The stake has a wire-way slot in the cap for easy fixture wire routing, and the fixture locknut secures the fixture to the top of the cap. The stake is for use with low voltage fixtures only.

Here are some of the key features and benefits of the Hadco S8 Low Voltage Mounting Stake:

  • Easy installation in soft or hard soil
CAP
SCREW IN CAP
WIREWAY SLOT
STAKE
LOW VOLTAGE FIXTURE
FIXTURE LOCKNUT
FIXTURE WIRE
LOW VOLTAGE
CABLE CONNECTOR
BLOCK OF WOOD
32000613, revision G
100 Craftway, P.O. Box 128
Littlestown, Pennsylvania 17340-0128
Phone: 800-331-4185 Fax: 717-359-9672
INSTALLATION INSTRUCTIONS:
S7 OR S8 LOW VOLTAGE
MOUNTING STAKE
page 1 of 2
SAFETY WARNING:
ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE
PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING!
This fixture can become very HOT! The fixture housing and lens, especially if it is glass, can become hot enough
to blister hands. Attention should be paid to where the fixture is mounted, particularly if it can be touched by
children or pets. To help prevent premature failure, decreased performance, overheating and risk of fire, keep
fixture and lens clean and free of leaves, mulch, debris and mineral deposits from water. The fixture and lens
can be cleaned using a soft cloth and a solution of mild liquid soap and warm water. Wipe clean and dry with a
soft, lint-free dry cloth. Avoid polishing fixture or lens.
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS!
WARNING - Lamp gets HOT quickly! To reduce the risk of FIRE OR INJURY TO PERSONS:
Do not operate fixture with a missing or damaged lens/lens assembly.
Contact only switch or plug when turning fixture on or off. Do NOT touch hot lens or housing.
Turn off or unplug fixture and allow to cool before relamping. Keep lamp away from combustibles.
Do NOT touch lamp with bare hands at any time, use a soft cloth as oil from skin may damage lamp.
7. Warning: This stake is for use with low voltage fixtures only.
6. Connect fixture wire to low voltage cable per the installation instructions for the fixture.
until it is in the correct position. Tighten the screw on the side of the cap.
5. Install the fixture and cap onto the top of the stake. Fixture wire exits through wire-way slot in cap. Turn the fixture
4. Screw the cap onto the fixture and tighten the fixture's locknut against the top of the cap.
stake above ground level. Hold the stake straight while backfilling and compacting the soil.
3. For installations in hard or rocky soil: Dig a hole for the stake. Place stake in hole with the top cylinder of the
striking the wood with a hammer.
from flaring out when striking, place a block of wood on top of the stake and drive the stake into the ground by
2. For installations in soft soil: The stake can be installed without excavating the soil. To prevent the top of the stake
1. Loosen screw on side of cap and remove cap from stake.
INSTALLATION INSTRUCTIONS
covered, please contact your distributor for assistance.
void the warranty. These instructions cover most installation applications. For any special applications not
Failure to adhere to these codes and instructions may result in serious injury and/or damage to the stake, and will
This stake is intended for installation in accordance with the National Electrical Code and local code specifications.
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING THIS STAKE.
page 2 of 2
32000613, revision G
  • Page 1 1
  • Page 2 2

Hadco S8 Low Voltage Mounting Stake Operating instructions

Hadco
Brand
Hadco
Model
S8 Low Voltage Mounting Stake
Type
Operating instructions
This manual is also suitable for

Hadco S8 Low Voltage Mounting Stake is designed for mounting low voltage fixtures outdoors, in accordance with the National Electrical Code and local code specifications. It is suitable for use in soft or hard soil, and can be installed without excavating the soil in soft soil conditions. The stake has a wire-way slot in the cap for easy fixture wire routing, and the fixture locknut secures the fixture to the top of the cap. The stake is for use with low voltage fixtures only.

Here are some of the key features and benefits of the Hadco S8 Low Voltage Mounting Stake:

  • Easy installation in soft or hard soil
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents