MD 13735
free phone
costs 7p/min from a BT landline,
mobile costs may be higher
0871 37 61 020
1-800-992 508
Wireless Digital Door
Chime
User's Guide
After Sales Support
Now you have purchased a Home Protector product you
can rest assured in the knowledge that as well as your
3 years part and labour warranty you have the added peace
of mind of dedicated helplines and web support.
Congratulations! You have made an excellent choice with the purchase of this quality
product. Our commitment to quality also includes our service. Should you, contrary to
expectations, experience defects due to manufacturing faults during private use within 36
months of the date of purchase we shall be liable for warranty in accordance with statutory
warranty regulations provided that:
- The device was not put to use other than the intended
- was not overloaded
- was not used with the wrong accessories
- repairs were not carried out by any other than the intended workshop
The warranty certificate is only valid in connection with an acceptable proof of purchase.
Please keep both in a safe place. This warranty does not affect your statutory rights.
This purchase is guaranteed for a period of three years beginning on the day of purchase.
Keep your purchase receipt safe as proof of date of purchase. The guarantee can only be
extended for the duration of any repair required.
During the warranty period defective devices can be returned to the service address stated
on the back cover of this document by first calling the service hotline number provided to
arrange collection by an approved freight agent at no cost to you. We will at our discretion,
either repair or exchange the device in accordance with warranty legislation.
Please enclose the following when sending your product in for repair:
1. Proof of purchase (receipt).
2. This warranty certificate with the fault report from overleaf complete with your name,
contact details and fault descrition.
If an acceptable proof of purchase is not enclosed the repair will be
charged in all cases. After the warranty has expired defective devices
can still be sent to the address stated below. Any repairs outside of the
warranty period will be charged and can only be undertaken once
payment has been received.
Ensure that the product is sent well packed as no responsability can be
accepted for items lost or damaged in transit.
This warranty does not affect your statutory right.
WARRANTY CARD
08/2012
Wireless Digital Door
Chime
In order to deal with your enquiry as quickly and efficiently as possible, we ask you to
contact our service hotline on the number detailed below.
UK IRELAND HELPLINE NO 0871 37 61 020
REP. IRELAND HELPLINE NO 1-800-992 508
Alternatively you can contact us via email by completing the Email product support
form which can be found on www.medion.co.uk
Medion Electronics Ltd.
120 Faraday Park, Faraday Road, Dorcan
Swindon SN3 5JF, Wiltshire
United Kingdom
Hotline: 0871 37 61 020
(calls are charged at 7p per min from a standard landline,
calls from mobiles could be higher)
Fax: 01793 71 57 16
www.medion.co.uk
Name
Adress
EMail
Daytime Tel No
Model Number
Fail Description
FAULT REPORT CARD
Transmitter
Overview of the device
Receiver
1) LED display
2) Volume control
3) Signal selector
4) Channel button
5) Ringer tone button
6) Speaker
7) Stand
8) Support eyelets
9) Battery compartment
10) Battery compartment cover
11) Locking plate
1) Bell push
2) Battery compartment
3) Snap joints for the wall mount
4) Wall mount eyelets
5) wall mount
6) Battery compartment cover
7) Wall mount brackets
8) Reset button
9) LED
10) Name plate
Wireless Digital
Door Chime
In order to deal with your enquiry as quickly and efficiently as possible, we ask you to
contact our service hotline on the number detailed below.
UK IRELAND HELPLINE NO 0871 37 61 020
REP. IRELAND HELPLINE NO 1-800-992 508
Alternatively you can contact us via email by completing the Email product support
form which can be found on www.medion.co.uk
Medion Electronics Ltd.
120 Faraday Park, Faraday Road, Dorcan
Swindon SN3 5JF, Wiltshire
United Kingdom
Hotline: 0871 37 61 020
(calls are charged at 7p per min from a standard landline,
calls from mobiles could be higher)
Fax: 01793 71 57 16
www.medion.co.uk
Name
Adress
EMail
Daytime Tel No
Model Number
Fail Description
FAULT REPORT CARD
Transmitter
Overview of the device
Receiver
1) LED display
2) Volume control
3) Signal selector
4) Channel button
5) Ringer tone button
6) Speaker
7) Stand
8) Support eyelets
9) Battery compartment
10) Battery compartment cover
11) Locking plate
1) Bell push
2) Battery compartment
3) Snap joints for the wall mount
4) Wall mount eyelets
5) wall mount
6) Battery compartment cover
7) Wall mount brackets
8) Reset button
9) LED
10) Name plate
Wireless Digital
Door Chime
1
Contents
2 Introduction
2
General information
4
Safety instructions
8
Assembly and part list
9
Overview of the device
11
Getting started
13
Free-standing set-up / wall mounting
17
Cleaning
17
Disposal
18
Technical data
19
Declaration of conformity
13735 UK ALDI Content Final rv1.indd 113735 UK ALDI Content Final rv1.indd 1 24.05.2012 14:34:2124.05.2012 14:34:21
2
1 Introduction
Congratulations!
You have made an excellent choice with the purchase of this
quality Home Protector® brand product. By doing so you
now have the assurance and peace of mind which comes
from purchasing a product that has been manufactured to
the highest standards of performance and safety, supported
by the high quality standards of Aldi.
We want you to be completely satisfied with your
purchase so this Home Protector® product is backed by
a comprehensive manufacturer’s 3 year warranty and an
outstanding after sales service through our dedicated
Helpline. We hope you will enjoy using your purchase for
many years to come.
2 General information
Please read these instructions carefully before
using the system and note the warnings in the
operating instructions.
This device should only be used as designated
and described in these instructions.
Always keep the operating instructions close
to hand. If you sell the appliance or give it
away, please ensure that you also pass on these
instructions.
13735 UK ALDI Content Final rv1.indd 213735 UK ALDI Content Final rv1.indd 2 24.05.2012 14:34:2624.05.2012 14:34:26
3
Symbols and key words used in
these instructions
DANGER!
Warning: immediate mortal danger!
WARNING!
Warning: possible mortal danger and/or
serious irreversible injuries!
CAUTION!
Please follow the guidelines to avoid
injuries and/or property damage!
ATTENTION!
Please follow the guidelines to avoid
property damage!
PLEASE NOTE!
Additional information on
using the device
PLEASE NOTE!
Please follow the guidelines in the
operating
instructions!
WARNING!
Warning: danger of
electric shock
•
Bullet point/information on operating
steps and results
Tasks to be performed
Proper use
Your wireless door chime is intended to send an acoustic
and/or optical signal to the receiver when the doorbell
button is activated. Do not attempt to modify the device
and do not useit for other purposes.
13735 UK ALDI Content Final rv1.indd 313735 UK ALDI Content Final rv1.indd 3 24.05.2012 14:34:2624.05.2012 14:34:26
4
3 Safety instructions
Dangers for children and people
with reduced ability to operate
devices
•
This device may be used by children over the age of
8 and by persons with reduced physical, sensory or
mental abilities or by those without experience and/
or knowledge, if they are supervised or have been
instructed in the safe use of the device and have
understood the dangers that result from it.
• Children must not play with the device. Cleaning and
user maintenance must not be carried out by children,
unless they are aged 8 or over and are supervised.
• Children younger than 8 should be kept away from the
device.
• Keep the device and its accessories out of reach of
children.
DANGER!
Keep the plastic wrapping out of the reach
of children. There is a risk of suffocation.
13735 UK ALDI Content Final rv1.indd 413735 UK ALDI Content Final rv1.indd 4 24.05.2012 14:34:2624.05.2012 14:34:26
5
Battery information
You will need batteries to operate the wireless doorbell.
Batteries may contain combustible materials. If not handled
properly, batteries may leak, heat up excessively, ignite or
even explode, which could result in damage to the device
and your health.
Warning!
Risk of explosion if batteries are replaced
incorrectly.
Dispose of used batteries according to
instructions.
Please note the following advice:
• Keep batteries away from children.
• Contact your doctor immediately if a battery is
swallowed.
• Never charge non-rechargeable batteries.
Risk of explosion!
• Never create a short-circuit between the batteries and
the connection terminals of the device.
• Never expose the batteries to excessive heat such as
sunlight, fire or similar.
• Do not dismantle or deform the batteries.
You could injure your hands or fingers or battery
fluid could come into contact with your eyes or skin.
If this happens, rinse the affected areas immediately
with plenty of clean water and contact your doctor
immediately.
• Avoid heavy impacts and vibrations.
• If necessary, clean the battery and device contacts
before insertion.
• Always observe the correct polarity.
• Make sure that the plus (+) and minus (-) poles are
correctly inserted to avoid short circuits.
• Do not mix up new and old batteries or different types
of batteries. This could cause your device to malfunction.
In addition, the weaker batteries would discharge too
much.
13735 UK ALDI Content Final rv1.indd 513735 UK ALDI Content Final rv1.indd 5 24.05.2012 14:34:2724.05.2012 14:34:27
6
Remove used batteries from the device immediately.
Remove the batteries from the device if you do not
intend to use it for a long period of time.
Replace all of the old batteries in a device with new
batteries of the same type.
Cover the contacts of the batteries with sticky tape if you
want to store or dispose of them.
13735 UK ALDI Content Final rv1.indd 613735 UK ALDI Content Final rv1.indd 6 24.05.2012 14:34:2724.05.2012 14:34:27
7
Environmental requirements
Transmitter
• The transmitter has a splash-proof housing.
• In optimum conditions, the transmitter has a range of
100 m. This can be reduced by structural conditions.
• Sources of interference for the transmitter can include:
mounting on metallic objects, reinforced concrete, high-
frequency interference of any kind, devices operating on
neighbouring frequencies, poorly screened computers.
Receiver
• Protect the wireless door chime’s receiver from moisture
and heat.
• Avoid placing or mounting the receiver in poorly
ventilated areas (such as between shelves or where
curtains or furniture can block the vents).
• Do not allow foreign bodies or liquids to get into the
device. Do not expose it to dripping water or spray. Do
not place objects that are filled with water, such as vases,
on the device.
• Naked flames, such as lit candles, must not be placed on
the device.
Never carry out repairs yourself
PLEASE NOTE!
If there is a fault, contact the MEDION Service
Centre or other suitable specialist workshop.
13735 UK ALDI Content Final rv1.indd 713735 UK ALDI Content Final rv1.indd 7 24.05.2012 14:34:2724.05.2012 14:34:27
8
4 Assembly and part
list
When unpacking, ensure that the following parts have been
supplied:
• Transmitter
• 1 x 3 V battery CR2032 for the transmitter
• Receiver
• 2 x AA batteries for the receiver
• Assembly material (4 screws, 4 wall plugs, 5 name plates)
• These operating instructions and guarantee documents.
Please contact us within 14 days if anything is missing from
the package contents.
13735 UK ALDI Content Final rv1.indd 813735 UK ALDI Content Final rv1.indd 8 24.05.2012 14:34:2724.05.2012 14:34:27
9
5 Overview of the
device
Receiver
1) LED display 7) Stand
2) Volume control 8) Support eyelets
3) Signal selector 9) Battery compartment
4) Channel button 10) Battery compartment
cover
5) Ring tone selection button 11) Locking plate
6) Speakers
13735 UK ALDI Content Final rv1.indd 913735 UK ALDI Content Final rv1.indd 9 24.05.2012 14:34:2724.05.2012 14:34:27
10
Transmitter
1) Bell push 6) Battery compartment
cover
2) Battery compartment 7) Wall mount brackets
3) Snap joints for the
wall mount
8) Reset button
4) Wall mount eyelets 9) LED
5) Wall mount 10) Name plate
13735 UK ALDI Content Final rv1.indd 1013735 UK ALDI Content Final rv1.indd 10 24.05.2012 14:34:2724.05.2012 14:34:27
11
6 Getting started
Inserting batteries
Transmitter
The transmitter requires one 3 V battery, size CR2032.
Loosen the retaining tabs to remove the front cover.
Un crew the screw of the battery compartment cover.
The transmitter is splash-proof and the cover fits
securely onto the battery compartment. Use a sturdy,
thin object (such as a small slot screwdriver) to gently lift
the battery compartment cover.
Make sure that the polarity of the battery is correct
(+ pole facing up). Insert the battery under the guide
lugs (2). Press the battery down gently until you hear it
click into the retaining lug (1).
Place the battery compartment cover back onto the battery
compartment and screw it back into place.
To put the front cover back onto the housing, hook the
retaining lug facing the circuit board into the top snap
joint and then gently press the front cover onto the
housing until you hear it click into place.
Receiver
The receiver requires two 1.5 V batteries, size AA (L6/LR6).
Remove the battery compartment cover.
Insert the batteries. Observe correct polarity! The
negative poles should each be on the spring.
Replace the battery compartment cover.
13735 UK ALDI Content Final rv1.indd 1113735 UK ALDI Content Final rv1.indd 11 24.05.2012 14:34:2724.05.2012 14:34:27
12
Using the device for the first time
For the wireless door chime to work, the transmitter and the
receiver must be synchronised.
After the batteries have been inserted into the receiver,
a ring tone will sound for a few seconds and the LED will
begin to light up.
Follow the instructions below to synchronise the transmitter
with the receiver.
Press the bell button on the transmitter, while the
receiver’s LED lights up.
A ring tone will be heard after which the transmitter is
synchronised with the receiver.
If the LED goes out before you have synchronised the
device, begin the synchronisation process again.
Ringer tone and volume
You can set the ringer tone and volume on the receiver and
change these settings at any time.
Press the ringer tone button repeatedly to select
between any one of 16 ringer tones/melodies.
Set the volume using the volume control VOL.
1 = low; 2 = medium; 3 = high.
Use the signal selector to choose the type of signal:
Ringer tone only
Flashing blue LED only
Ringer tone and flashing blue LED
Signals when ringing
Depending on the settings made with the signal selector,
the blue LED on the receiver flashes and/or a ringer tone or
melody is played.
13735 UK ALDI Content Final rv1.indd 1213735 UK ALDI Content Final rv1.indd 12 24.05.2012 14:34:2724.05.2012 14:34:27
13
7 Free-standing set-
up/wall mounting
Mounting the receiver
WARNING!
Choose a suitable location for mounting
the devices and make sure that you do
not damage any concealed electrical or
installation cables when drilling.
You can use the supporting eyelets on the rear side of the
device to mount the receiver on a wall.
Drill two holes suitable for 6 mm wall plugs.
Insert the wall plugs.
Screw in the large screws but leave the head projecting
out.
You can now hang the receiver on the screw heads.
Setting up the receiver
The base of the device is shaped like a stand so that you
can also stand up the device.
Select a smooth, non-slip surface for standing up the
device.
13735 UK ALDI Content Final rv1.indd 1313735 UK ALDI Content Final rv1.indd 13 24.05.2012 14:34:2824.05.2012 14:34:28
14
Mounting the device base
Hook one of the base’s hooks into the receiver (1).
Now press the base further onto the receiver, as shown,
until the second hook clicks into place (2).
Mounting the transmitter
Find a suitable place by the door for mounting the doorbell.
PLEASE NOTE!
Before mounting the transmitter, test to see
whether the transmitter signal can be picked up
by the receiver. Do not mount the transmitted
onto metal.
13735 UK ALDI Content Final rv1.indd 1413735 UK ALDI Content Final rv1.indd 14 24.05.2012 14:34:2824.05.2012 14:34:28
15
Screw on the wall mount
Remove wall mount from the transmitter.
This wall mount is attached to the wall as a back plate.
Mark the two drill holes on the wall.
Drill two holes suitable for 6 mm wall plugs.
Insert the wall plugs.
Screw on the wall mount using two of the screws.
Put the housing onto the wall mount and press it gently
until you hear it click into place.
Name plate
Label one of the supplied name plates.
If you decide to label the name plate by hand, we
recommend using a pen with waterproof ink.
Slide the cover of the name plate panel to the side and
insert your name plate.
Make sure that the name plate is right next to the LED
display so that the cover can be completely closed again.
Slide the name plate panel back onto the bell.
13735 UK ALDI Content Final rv1.indd 1513735 UK ALDI Content Final rv1.indd 15 24.05.2012 14:34:2824.05.2012 14:34:28
16
Changing the battery in the
transmitter
Open the battery compartment lid on the transmitter.
Use your finger or a pointed object (e.g. the nib of a
ballpoint pen or a toothpick) to carefully lift the battery
out of the compartment (1).
Synchronisation
After inserting new batteries or replacing spent batteries,
the transmitter and receiver may have to be synchronised.
After changing batteries, please test the function first. If you
do not have a connection, synchronise as follows:
Press the transmitter button on the receiver.
Press the bell button on the transmitter. The selected
melody will play and/or the LED on the receiver
will flash. The transmitter and the receiver are now
synchronised.
You can synchronise a model MD 13735 transmitter with
several model MD 13735 receivers. To do so, follow the
procedure described above.
13735 UK ALDI Content Final rv1.indd 1613735 UK ALDI Content Final rv1.indd 16 24.05.2012 14:34:2824.05.2012 14:34:28
17
8 Cleaning
• Clean the receiver with a dry, soft cloth.
• Use a soft, moist cloth with a little detergent to clean the
transmitter.
• Avoid the use of chemical solutions and cleaning
products because these may damage the devices’
surface or markings.
9 Disposal
Packaging
Your device has been packaged to protect it
against transportation damage. The packaging
constituents are raw materials and can be
reused or recycled.
Device
Under no circumstances, should any
component of the wireless doorbell be
disposed of in the normal household rubbish.
Seek the advice of your local authority about
the local options for disposing of waste.
Batteries
Do not dispose of used batteries in household
rubbish. Batteries should be taken to a
collection point for used batteries.
13735 UK ALDI Content Final rv1.indd 1713735 UK ALDI Content Final rv1.indd 17 24.05.2012 14:34:2824.05.2012 14:34:28
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
