Nexgrill 720-0324 Owner's manual

STAINLESS STEEL GAS GRILL

USE AND CARE GUIDE

MODEL NO:720-0324

®

FOR OUTDOOR USE ONLY

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE

DO NOT RETURN TO PLACE OF PURCHASE.

MESSAGE TO OUR CONSUMERS

Thank you for selecting our stainless steel gas grill.

Because this appliance contains features which may not found on other grills, we recommend that you read this

entire booklet before your first use. Keep it in a handy place as it has answers to questions that may occur

during future use.

Please read this booklet carefully and be sure your gas grill is properly assembled, installed and maintained. Failure to

follow these instructions could result in serious bodily injury and/or property damage. This gas grill in intended for

outdoor use only and is not intended to be installed in or on recreational vehicles or boats.

NOTE TO INSTALLER: Leave these instructions with the consumer after installation.

NOTE TO CONSUMER: Retain for future reference.

TABLE OF CONTENTS

SECTION ONE

Precaution ……………………………. 1

Placement of the grill ………………… 3

SECTION TWO

Assembly instructions ………………... 4

SECTION THREE

Gas hook-up ………………………… 20

Leak testing ……….……………….....22

Installer final check list ………………22

Operation instructions ………………..23

Grill lighting instructions …………… 24

SECTION FOUR

Using side burner …………………… 25

SECTION FIVE

Care and maintenance …………………. 26

Lighting Illustration…………………… 27

To match light the grill………………….29

Care and maintenance……………… ….30

Troubleshooting ……………………….. 30

SECTION SIX

Enlarge view …………………….…….. 32

Parts list ……………………………….. 33

Ordering parts ………………………….. 35

Grill hints ………………………………. 38

SECTION SEVEN

Grill cooking chart …………………… 35

SECTION EIGHT

Grill recipe suggestions ……………….. 38

SECTION NINE

Warranty ………………………………. 41

PRECAUTIONS

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, immediately call your gas

supplier.

WARNING

Do not try to light this appliance without first

reading the “LIGHTING INSTRUCTIONS”

section in this manual.

FOR YOUR SAFETY

1. Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

2. An LP cylinder not connected for use shall not

be stored in the vicinity of this or any other

appliance..

TESTED IN ACCORDANCE WITH ANSI Z21.58

/ CGA 1.6 STANDARD FOR OUTDOOR

COOKING GAS APPLIANCES. THIS GRILL IS

FOR OUTDOOR USE ONLY.

Check your local building codes for the proper

method of installation. In the absence of local codes,

this unit should be installed in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54,

ANSI/NFPA 58 OR CGA B149.1 Natural Gas and

Propane Installation Code, and the National Electrical

Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1.

CALIFORNIA PROPOSITION 65-WARNING

The burning of gas fuel generates some by-products,

which are on the list of substances, which are known by

the State of California to cause cancer or reproductive

harm. California law requires businesses to warn

customers of potential exposure to such substances. To

minimize exposure to these substances, always operate

this unit according to the use and care manual, ensuring

you provide good ventilation when cooking with gas.

SAFETY PRACTICES TO AVOID

PERSONAL INJURY

When properly cared for, your stainless steel grill will

give safe, reliable service for many years. However,

extreme care must be used since the grill produces

intense heat and that can increase accident potential.

When using this appliance basic safety practices must

be followed, including the following:

Read this Care and Use Manual carefully and

completely before using your grill to reduce the risk of

fire, burn hazard or other injury.

Do not repair or replace any part of the grill unless

specifically recommended in this manual. All other

service should be referred to a qualified technician.

CHILDREN SHOULD NOT BE LEFT ALONE OR

UNATTENDED IN AN AREA WHERE THE GRILL

IS BEING USED. NEVER ALLOW THEM TO SIT,

STAND OR PLAY ON OR AROUND THE GRILL AT

ANY TIME.

1

PRECAUTIONS

Moist or damp potholders on hot surfaces may cause

burns from steam. Do not use a towel or bulky cloth in

place of potholders. Do not let potholders touch hot

portions of the grill rack.

Grease is flammable. Let hot grease cool before

attempting to handle it. Avoid letting excess grease

deposits collect in the grease tray at the bottom of the

grill’s firebox. Clean often.

DO NOT USE ALUMINUM FOIL TO LINE THE

GRILL RACKS OR GRILL BOTTOM. This can severely

upset combustion air flow or trap excessive heat in the

control area.

For proper lighting and performance of the burners keep

the burner ports clean. It is necessary to clean them

periodically for optimum performance. The burners

will only operate in one position and must be mounted

correctly for safe operation.

Clean the grill with caution. Avoid steam burns; do not

use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce noxious fumes or can ignite if

applied to a hot surface.

INSECT WARNING!!! Spiders and insects can nest in

the burners of this and any other grill, and cause the gas

to flow improperly. This is a very dangerous condition

which can cause a fire to occur behind the valve panel,

thereby damaging the grill and making it unsafe to

operate. Inspect the grill twice a year.

Be sure all grill controls are turned off and the grill is

cool before using any type of aerosol cleaner on or

around the grill. The chemical that produces the

spraying action could, in the presence of heat, ignite or

cause metal parts to corrode.

DO NOT STORE ITEMS THAT ATTRACT CHILDEN

AROUND OR BELOW THE GRILL OR IN THE CART.

NEVER ALLOW CHILDREN TO CRAWL INSIDE OF

THE CART.

Never let clothing, pot holders or other flammable

materials come in contact with or too close to any

grate, burner or hot surface until it has cooled. Fabric

may ignite and result in personal injury.

For personal safety, wear proper apparel. Loose fitting

garments or sleeves should never be worn while using

this appliance. Some synthetic fabrics are highly

flammable and should not be worn while cooking.

Only certain types of glass, heat-proof glass ceramic,

earthenware, or other glazed utensils are suitable for

grill use. These types of materials may break with

sudden temperature changes. Use only on low or

medium heat settings according to the manufacturer’s

directions.

Do not heat unopened food containers as a build-up of

pressure may cause the container to burst.

Use a covered hand when opening the grill lid. Never

lean over an open grill.

WHEN LIGHTING A BURNER, ALWAYS PAY

CLOSE ATTENTION TO WHAT YOU ARE DOING.

BE CERTAIN YOU ARE TURNING THE IGNITER

LABELED FOR THE BURNER YOU INTEND ON

USING.

When using the grill, do not touch the grill rack,

burner grate or immediate surroundings as these

areas become extremely hot and could cause burns.

Use only dry potholders.

2

PRECAUTIONS

Do not use the grill for cooking excessively fatty

meats or products which promote flare-ups. Do not

operate the grill under unprotected combustible

construction. Use only in well ventilated areas. Do not

use in buildings, garages, sheds, breezeways or other

such enclosed areas. THIS UNIT IS FOR OUTDOOR

USE ONLY.

Keep the area surrounding the grill free from

combustible materials, trash, or combustible fluids and

vapors such as gasoline or charcoal lighter fluid. A

minimum of 24” clearance away from combustible

material. Do not obstruct the flow of combustion and

ventilation air. If the unit is stored indoors ensure that

it is cool. If propane is used, the cylinder must be

unhooked and the propane cylinder stored outside in a

well ventilated area, out of the reach of children.

DO NOT USE BRIQUETTES OF ANY KIND IN THE

GRILL.

This stainless steel grill is designed for optimum

performance without the use of briquettes. Do not place

briquettes on the radiant as this will block off the area

for the grill burners to vent. Adding briquettes can

damage ignition components and knobs, and void the

warranty.

Keep the back of the cart free and clear from debris.

Keep any electrical supply cord, or the rotisserie motor

cord away from the heated areas of the grill.

Never use the grill in extremely windy conditions. If

located in a consistently windy area (oceanfront,

mountaintop, etc.) a windbreak will be required (see

below). Always adhere to the specified clearance.

NEVER USE A DENTED OR RUSTY PROPANE TANK.

PLACEMENT OF THE GRILL

CLEARANCE

To Non-Combustible Construction

A minimum of 3” clearance from the back of the grill

to non-combustible construction is required for the lid

to open fully.

DO NOT INSTALL THIS UNIT INTO COMBUSTIBLE

ENCLOSURES!

LOCATION

When determining a suitable location take into

account concerns such as exposure to wind, proximity

to traffic paths and keeping any gas supply lines as

short as possible.

Locate the grill only in a well-ventilated area. Never locate

the grill in a building, garage, breezeway, shed or other such

enclosed areas without an approved ventilation system.

During heavy use, the grill will produce a lot of smoke. After

the grill is placed in a suitable position, lock the wheels

according to the sticker located beneath the right door. Keep

any electrical supply cord and the fuel supply hose away from

any heated surfaces. Storage of an outdoor gas cooking

appliance indoor is permissible only if the cylinder is

disconnected and removed from the appliance.

This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage or any

other enclosed area. This appliance is not intended to be

installed on recreational vehicles and/or boats.

3

ASSEMBLY INSTRUCTIONS

PLEASE READ THE INSTRUCTIONS THROUGHLY AND FOLLOW STEP

BY STEP.

HARDWARE PACK DESCRIPTION SPECIFICATION QUANTITY

A TRUSS HEAD SCREW 1/4”X10MM 4PCS

SPLIT LOCK 1/4” 4PCS

B TRUSS HEAD SCREW 5/32”X10MM 9PCS

SPLIT LOCK 5/32” 9PCS

C TRUSS HEAD SCREW 1/4” X15MM 49PCS

SPLIT LOCK 1/4” 49PCS

REMARK: EXTRA 2 MORE PICECS IN EACH HARDWARE PACK.

WRENCH: USED FOR STEP 10 SIDE BURNER VALVE ASSEMBLY.

Pack A Pack B Pack C

STEP 1: Take out bottom panel and four casters from the carton, Use 16 pcs of truss head screw

(1/4”x15mm ) and 16 pcs of 1/4”split lock (pack C) to lock two casters which in the right of bottom

panel and two casters with brake which in the left of bottom panel as shown figure below.

Pack C

4

ASSEMBLY INSTRUCTIONS

STEP 2: Use 6 pcs of truss head screw(1/4”x15mm ) and 6 pcs of split lock (pack C), to

Screw the left and right side panels to the bottom panel as shown figure below. When installing

the right and left panel, the flat side must face outside.

Pack C

STEP 3: Assemble back panel to bottom panel with 3 pieces of truss head screw(1/4”x15mm ) and

3pieces of 1/4” split lock (Pack C). When installing the back panel, the flat side must face outside.

5

ASSEMBLY INSTRUCTIONS

STEP 4: Assemble the two side panels with 2 pcs of truss head screw (1/4”x15mm)and

2 pieces split lock (pack C) to the back panel.

Pack C

Pack B

6

Step 5: Assemble the leg of clapboard with 2pcs of truss head 5/32”x10mm screw and 2pcs split lock

(pack B ) to the bottom panel as shown figure below.

STEP 7:Assemble the cart frame with 4 pieces of 1/4”x15mm truss head screw and 4 pieces of split

lock(pack C) to the side panels as shown figure below.

Step 6: Assemble the clapboard with 2pcs of 5/32”x10mm truss head screw and 2pcs of split lock

(Pack B) to the leg as shown figure below.

Pack C

Pack B

ASSEMBLY INSTRUCTIONS

7

ASSEMBLY INSTRUCTIONS

Step 8:Use 2pcs of 5/32”x10mm truss head screw and 2pcs split lock(pack B) to screw the

Individual panel to the back panel as shown figure below.

Step 9: Fix the individual panel with 2pcs of 5/32”x10mm truss head screw and 2pcs split lock(pack B)

to the cart frame as shown figure below.

Pack B

8

ASSEMBLY INSTRUCTIONS

Step10: A: Assemble the left door: To insert the door in the hole of extended metal piece at the

grill bottom;press the hinge on the top of the door to insert it into the hole on upper extended

metal piece as shown figure below..

B:Assemble the right door in the same way as step A.

Step 11:Hang up the spice tray into the holes of left and right door.(see figure below)

9

ASSEMBLY INSTRUCTIONS

STEP 12: Insert the upper portion of grill onto the cart from top as shown figure below.

Caution!The firebox is heavy,and we recommend two or more people to lift up firebox.

10

100

200

300

400

500

600

700

800

ASSEMBLY INSTRUCTIONS

Step 13: Open the lid ,take out the cooking grid first, screw tighten the fire box with

3pcs of

5/32”x10mm truss head screw and 3pcs split lock(pack B) to the back panel.

Then use 4pcs of

1/4”x15mm truss head (Pack C)and 4pcs of split lock to screw the

fire box to the side panels.

Pack C

Pack B

11

ASSEMBLY INSTRUCTIONS

STEP 14 :A: Assembly the side shelf with 6 truss head 1/4”x15mm screw with 6 split lock

(pack C) to the left panel as shown figure below.

B: Assemble the side burner with 6 truss head 1/4”x15mm screw with 6 split lock (pack C) to

the right panel.

Pack C

12

ASSEMBLY INSTRUCTIONS

Step:15 Side burner valve assembly:

Step 1: Insert valve assembly through side Step 2: Remove 4(four) screw&split lock

panel from the “U” brackets on the side

(Side panel, right) burner.

Step 3: Insert valve stem assembly into burner Step 4: Insert valve stem assembly into

tube. face-plate.

13

14

ASSEMBLY INSTRUCTIONS

Step 5: Replace “U” brackets with 4(four) Step 6: Align & tighten knob seat &valve

Screws( DO NOT TIGHTEN) stem with 2(two)screws&split lock

Note:(Make sure hose is not bent) as shown below.

Knob Seat

Valve Stem

Step 7;Tighten all 4(four) screws on the “U” Step 8: Place knob on valve stem and secure

the ignition wire on to valve.

brackets on the burner, then connect with the wrench tool.

Ignition wire

(wrench tool enclosed in bag)

**Important Note! Make Sure Side Burner Hose Is not Bent**

ASSEMBLY INSTRUCTIONS

15

100

200

300

400

500

600

700

800

Step 16: Hang up the 4 utensil hook into the holes in the side shelf.

100

200

300

400

500

600

700

800

Step 17: Assemble the push bar with 2pcs of 1/4”x15mm screw with 2 split lock (pack C)

to the Side shelf.

ASSEMBLY INSTRUCTIONS

16

Step 18: Assemble the motor bracket with 2pcs of truss head 2 pieces of 1/4”x10mm screw

and 2 pieces of split lock (pack A)

the left side shelf.Then assemble the rotisserie kit as

shown figure below.

Pack A

ASSEMBLY INSTRUCTIONS

17

100

200

300

400

500

600

700

800

Step 19:Put the gas tank into the gas tank pull-out tray. Then tighten up the gas tank retention bolt.

g

C

L

O

S

E

O

P

E

N

1.With hand attach propane gas tank to regulator inlet fitting by turning the regulator clockwise until tight

as shown in figure below.

2.LP gas cylinder must be fitted with a listed overfill prevention device(OPD) .

Step 20:To lock and unlock the liquid propane gas cylinder tray,press the gas cylinder

Tray’s top button A to lock.Press the side button B to unlock.

A

B

A

800

700

600

500

400

300

200

100

ASSEMBLY INSTRUCTIONS

18

Page is loading ...

Nexgrill 720-0324 Owner's manual

Nexgrill 720-0324 Owner's manual

Related papers

Other documents