Roland HP-201 Owner's manual

1

■

Parts Check

Before you begin assembling the stand, check that all the parts

were supplied. You will also need to have a Phillips screwdriver.

A: Side Board (left) 1: Screw “a” (M5 x 40 mm) x4

B: Side Board (right) 2: Screw “b” (M5 x 20 mm) x6

C: Pedal Board

D: Rear Board

■

Assembly Procedure

* Fasten each screw tightly, then place the stand in a stable and horizontal place.

Also, carry out assembly of the instrument on an even surface.

* Do not allow the pedal cord or power cable to get twisted or pinched while

assembling the stand.

* Do not set up the instrument on long-piled carpeting. This can cause instability

in the stand and unsteadiness in the pedals, possibly resulting in damage to the

unit.

* Lay a soft cloth or similar material on the floor, and assemble the stand atop this

surface.

* When tightening the screws, turn them two or three revolutions by hand before

using a screwdriver.

Stand Assembly

1.

Attach the side boards for the right and left sides to the

pedal board (so that the metal parts face inside) using

screws “a” (M5 x 40 mm).

* When attaching the pedalboard, do not allow any gap to remain between the side

board and pedalboard when the pieces are assembled.

2.

Loosen the screws attached to the left and right side

boards approximately three turns, so that they protrude

about 3mm, as shown in the illustration.

3.

Hook the metal brackets of the rear board over the screws

you loosened (c), as shown in the illustration.

4.

Use four screws “b” (M5 x 20mm) to provisionally fasten

the pedal board.

5.

Securely tighten the two side board screws and four pedal

board screws.

- Make sure that another person is on hand to help with the assembly and setup.

- Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your

hands or feet.

- To move the piano, lift it carefully—all the while keeping it level.

- Be sure to keep any screws, caps, and other small components out of the reach of small children so as to

prevent any child from accidentally swallowing these items.

- Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or

stripping the screws.

KSC-40/42

STAND ASSEMBLY

Copyright

©

2007 ROLAND CORPORATION

KSC-42

At first, assemble the entire stand in a temporary fashion, without really

tightening the screws. Then, after checking the overall alignment of the

boards (and gently shifting certain parts where necessary), go around

and tightly fasten each of the screws.

1

Screw “a” 2pcs

Correct

Improper

Side board

Space

Pedal

board

Pedal board

2

When attaching the rear board, before tightening the screws, adjust

things as necessary at all the points where there are screws so as to assure

that the rear board is aligned in parallel with the pedal board.

3

4, 5

5

Screws you loosened

in step 2 (2 screws)

Screw “b” (4 pieces)

Rear view

KSC-4042.fm 1 ページ２００８年８月７日　木曜日　午後５時１０分

2

Installing the Piano on the Stand

6.

Align the protruding screws (one each at right and left) on

the bottom of the piano with the openings in the metal

fittings on the side board, then slide the piano forward until

the screws are held in place.

* When handling the piano, firmly grasp it. Be careful, so you do not get your

fingers pinched.

7.

Fasten the piano to the stand with the screw “b” (M5 x

20mm).

Connecting the Pedal and Power Cords

8.

Connect the pedal cord to the Pedal connector.

9.

Connect the power cord to the AC Inlet on the piano, then

plug the other end into AC Outlet.

10.

Secure the pedal cord and power cord in place with the

coated clip at the lower rear of the piano.

Adjusting the Adjuster

11.

Lower the adjuster at the bottom of the pedal board (by

rotating it), so that the adjuster touches the floor. If you

have the piano placed on a carpet, lower it until it pushes

into the carpet.

When Moving the Piano

Disconnect the power cord , cables, and raise the stand’s

adjuster. Then lift the piano while keeping it level, and

move it with care, so that you do not drop it on your feet,

or get your hands caught.

6

7

Screw “b”

Please don’t get your

fingers pinched.

98

Coated clip

11

Adjuster

KSC-4042.fm 2 ページ２００８年８月７日　木曜日　午後５時１０分

Page is loading ...

Roland HP-201 Owner's manual

This manual is also suitable for

Roland HP-201 Owner's manual

in other languages

Related papers

Other documents