Panasonic EY3552GQW Owner's manual

Page is loading ...

-

2

-

Index/Index/Index/Indice/Index/Indice/Indeks/Index/Indeks/Hakemisto/

Индекс/Індекс

English: Page 8

Deutsch: Seite 19

Français: Page 28

Italiano: Pagina 38

Nederlands: Bladzijde 48

Español: Página 58

FUNCTIONAL DESCRIPTION

FUNKTIONSBESCHREIBUNG

DESCRIPTION DES FONCTIONS

DESCRIZIONE DELLE FUNZIONI

FUNCTIEBESCHRIJVING

DESCRIPCIÓN FUNCIONAL

FUNKTIONSBESKRIVELSE

FUNKTIONSBESKRIVNING

FUNKSJONSBESKRIVELSE

TOIMINTOJEN KUVAUS

ФУНКЦИОНАЛЬНОЕ ОПИСАНИЕ

ФУНКЦIОНАЛЬНИЙ ОПИС

K ML

A

C

D

B

E

F

G

I

H

J

O

N

Fig. 1

Dansk: Side 67

Svenska: Sid 76

Norsk: Side 85

Suomi: Sivu 94

Русский: Страница 103

Українська: Сторiнка 113

Page is loading ...

-

8

-

I. INTRODUCTION

Thank you for purchasing the Panasonic Metal

Cutter. The powerful cutting action of this cutter,

combined with the convenience of its recharge-

able battery pack, provides you with great metal

cutting performance.

This Metal Cutter is only to be used for cutting

unhardened ferrous metal.

DANGER

This product is a cutting tool, designed to cut

through metal. It has a rotating blade which is

capable of cutting you deeply, causing seri-

ous injury or death. As a result, please read

this manual and the cautionary markings on

the tool carefully, and obey all of the Safety

Instructions to avoid such injury.

WARNING

To avoid injury, never insert your finger or any

other object into any opening of the metal cutter.

How to Use This Manual

•Please read this manual completely before start-

ing to cut with your metal cutter. If you let some-

one else use the metal cutter, make sure they

either read this manual or are fully instructed in

the proper use and all safety precautions con-

cerning the metal cutter.

•Please keep this manual for future reference. It

contains important safety information that you

must follow to use the metal cutter safely.

•This manual and product use the following signal

words:

NOTE

Notes provide additional information that you

should know about the metal cutter.

CAUTION

Caution indicates a potentially hazardous situ-

ation, which could result in minor or moderate

injury if not avoided. Cautions also alert you to

unsafe practices to be avoided.

WARNING

Warning indicates a potentially hazardous situa-

tion, which could result in serious injury or death

if not avoided.

DANGER

Danger indicates a imminent hazard which will

result in serious injury or death if not avoided.

Read “the Safety Instructions” booklet and the

following before using.

II.

ADDITIONAL SAFETY

RULES

Safety instructions for all

saws

DANGER

• Keep hands away from cutting area and

the blade. Keep your second hand on

auxiliary handle, or motor housing. If both

hands are holding the saw, they cannot be

cut by the blade.

• Do not reach underneath the workpiece.

The guard cannot protect you from the

blade below the workpiece.

• Adjust the cutting depth to the thickness

of the workpiece. Less than a full tooth of

the blade teeth should be visible below the

workpiece.

• Never hold piece being cut in your hands

or across your leg. Secure the workpiece

to a stable platform. It is important to sup-

port the work properly to minimize body

exposure, blade binding, or loss of control.

• Hold power tool by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hid-

den wiring or its own cord. Contact with

a “live” wire will also make exposed metal

parts of the power tool “live” and shock the

operator.

• When ripping always use a rip fence or

straight edge guide. This improves the

accuracy of cut and reduces the chance of

blade binding.

• Always use blades with correct size and

shape (diamond versus round) of arbour

holes. Blades that do not match the mount-

ing hardware of the saw will run eccentri-

cally, causing loss of control.

• Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw,

for optimum performance and safety of

operation.

-

9

-

Further safety instruc-

tions for all saws

Causes and operator prevention of kickback:

- kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the work-

piece toward the operator;

- when the blade is pinched or bound tightly

by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back

toward the operator;

- if the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood

causing the blade to climb out of the kerf and

jump back toward the operator.

Kickback is the result of saw misuse and/or incor-

rect operating procedures or conditions and can

be avoided by taking proper precautions as given

below.

1) Maintain a firm grip with both hands on the

saw and position your arms to resist kick-

back forces. Position your body to either

side of the blade, but not in line with the

blade.

Kickback could cause the saw to jump back-

wards, but kickback forces can be control-

led by the operator, if proper precautions are

taken.

2) When blade is binding, or when interrupt-

ing a cut for any reason, release the trig-

ger and hold the saw motionless in the

material until the blade comes to a com-

plete stop. Never attempt to remove the

saw from the work or pull the saw back-

ward while the blade is in motion or kick-

back may occur.

Investigate and take corrective actions to elim-

inate the cause of blade binding.

3) When restarting a saw in the workpiece,

center the saw blade in the kerf and check

that saw teeth are not engaged into the

material.

If saw blade is binding, it may walk up or kick-

back from the workpiece as the saw is restarted.

4) Support large panels to minimize the risk

of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under the

panel on both sides, near the line of cut and

near the edge of the panel.

5) Do not use dull or damaged blades.

Unsharpened or improperly set blades pro-

duce narrow kerf causing excessive friction,

blade binding and kickback.

6) Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

7) Use extra caution when making a “plunge

cut” into existing walls or other blind

areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions for

this saw

1) Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position.

If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with

the Lower Guard Lift Lever and make sure it

moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

2) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-

up of debris.

3) Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard

by Lower Guard Lift Lever and as soon as

blade enters the material, the lower guard

must be released.

For all other sawing, the lower guard should

operate automatically.

4) Always observe that the lower guard is

covering the blade before placing saw

down on bench or floor.

An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the

blade to stop after switch is released.

5) Do not use any abrasive wheels.

6) Wear a dust mask, if the work causes dust.

7) Use saw blades recommended by Manu-

facture.

8) Wear ear protectors when using the tool for

extended periods.

9) The risk of kickback increases as the bat-

tery pack discharges.

10) Be sure to inspect material. Avoid cutting

other different material.

-

10

-

11) Be careful not to drop Metal Cutter.

12) Never swing Metal Cutter.

13) Never cover the ventilation slots, and keep

them free from dust or other material.

14) Do not clamp Metal Cutter in a vise. Never

cut with Metal Cutter held upside down in a

vise. This is extremely dangerous and can

lead to serious accidents.

15) Never wear knitted gloves.

16) Be sure no one is below when using Metal

Cutter in high locations.

17) Do not touch the blade immediately after

operation. It may be hot and could burn

your skin.

18) Do not touch material after it has been cut.

Cut material may be very hot.

19) Do not use cutting oil. This use of cutting oil

may cause a fire.

20) Do not cut workpieces covered or stained

with gas, oil, solvents, thinners, etc.

Exposure to these materials may damage

the transparent guard.

21) Do not remove the transparent and lower

guards. If the transparent and lower guards

is damaged or missing, return tool to

authorized service center for replacement.

22) Do not start the blade when in contact with

workpiece. Wait for blade to reach full speed

before beginning cut.

Symbol

Meaning

V

Volts

Direct current

n

0

No load speed

··· / min

Revolutions or reciprocations

per minute

A

Amperes

III. SETTING UP

Charging Battery Pack EY9251

Charge the battery pack when the cutting speed

becomes too slow for effective cutting.

If you have two battery packs, you can use one to

continue working while charging the other one.

NOTE:

When you charge the battery pack for the first

time, or after prolonged storage, charge it for

about 24 hours to bring the battery up to full

capacity.

Battery charger (EY0110)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is

inserted into the AC power supply, but this is

not a problem in terms of safety.

2. Insert the battery pack firmly into the charger.

Battery

pack

To AC

outlet

Battery

charger

1

2

3. During charging, the charging lamp will be lit.

When charging is completed, an internal elec-

tronic switch will automatically be triggered to

prevent overcharging.

• Charging will not start if the battery pack

is warm (for example, immediately after

heavy-duty operation).

The orange standby lamp will be lit until the

battery cools down. Charging will then begin

automatically.

4. When charging is completed, the charging

lamp will start flashing quickly in green color.

5. When in any of the conditions that battery

pack is too cool, or the battery pack has not

been used for a long time, the charging lamp

is lit. In this case, charging takes longer to fully

charge the battery pack, than the standard

charging time.

• If a fully charged battery pack is inserted

into the charger again, the charging lamp

lights up. After several minutes, the charg-

ing lamp may flash quickly to indicate the

charging is completed.

-

11

-

6. If the charging lamp does not light immediately

after the charger is plugged in, or if after the

standard charging time the lamp does not go

off, consult an authorized dealer.

NOTE:

• When charging a cool battery pack (below 5°C

(41°F)) in a warm place, leave the battery pack

at the place and wait for more than one hour to

warm up the battery to the level of the ambient

temperature. Otherwise battery pack may not

be fully charged.

• Cool down the charger when charging more

than two battery packs consecutively.

• Do not insert your fingers into contact hole,

when holding charger or any other occasions.

CAUTION:

To prevent damage or risk of fire:

• Do not use power source from an engine gen-

erator.

• Do not cover vent holes on the charger and the

battery pack.

• Unplug the charger when not in use.

Lamp Indications

Red Flashing

Red Lit

Green Flashing quickly

Orange Lit

Orange Flashing

Charger is plugged into the AC outlet.

Ready to charge.

Now charging

Charging is completed.

Battery pack is warm. Charging will begin

when temperature of battery pack drops.

Charging is not possible. Clogged with

dust or malfunction of the battery pack.

-

12

-

Inserting Battery Pack

CAUTION:

Before inserting battery pack, check that the

power switch in the Metal Cutter actuates properly

and returns to the “OFF” position when released.

1.To insert the battery pack: (See Fig.2)

Slide the battery pack in place at the rear of

the metal cutter. The battery should snap into

place. If the battery is loose, it has not been

properly connected.

2.To remove the battery pack:

Press the two tabs on the sides of the battery

pack. Slide the battery pack out of the metal

cutter body.

IV. OPERATION

Before Using Metal Cutter

This tool is intended for cutting unhardened fer-

rous metal and nonferrous metal. Refer to the

“Accessories” section for a list of blades to be

used for the proper applications of this tool. The

following precautions must be followed to reduce

the risk of injury;

•Do not cut stacked materials. Cut one piece at a

time.

•Do not cut hardened steel.

•Cut materials with the wider edge of the shoe

over the clamped side of the material.

•Do not touch the saw blade, workpiece, or cutting

chips with bare hands immediately after cutting;

they may be hot and could burn skin.

Each time you use the metal cutter, you must

make sure it is in good operating condition.

Use the following checklist:

1.Is the blade installed in the correct direction?

The arrow on the blade must point in the same

direction as the arrow on the upper blade

cover.

2.Is the blade installed properly?

Make sure the hex bolt is tightened securely.

(See Fig.12)

3.Does the blade look alright?

Replace the blade immediately if there are any

cracks in it or if any teeth are broken.

4.Does the lower guard close properly?

WARNING

To avoid injury, do not use the metal cutter if

the lower guard does not close quickly over

the blade.

5.Is the transparent guard securely installed?

6.Is the battery pack charged and inserted firmly

to the metal cutter?

7.Is the depth adjustment lever for cutting

securely tightened?

8.Is the workpiece securely clamped on a saw

horse or bench?

Using Metal Cutter

CAUTION:

To reduce the risk of injury read the Safety

Instructions at the front of this manual before using

the metal cutter.

WARNING

To reduce the risk of injury, wear safety goggles

or glasses with side shields.

Follow these steps:

Hold the metal cutter with both hands. (See

Fig.4) Do not attempt to remove cut material

when blade is moving.

1.Line up the sight line on shoe with your cutting

line. (See Fig.3)

Alignment with cutting line

• Use the notch as guide to establish cutting

position. Align the notch with cutting line.

As the cutting position may differ depending on

the blade, do a trial cut beforehand.

2.Press the switch lock lever down, then

squeeze the power switch to start the motor,

and then release the switch lock lever.

CAUTION:

• Check that the switch lock lever works.

If power switch can be activated without

depressing the switch lock lever, discontinue

use immediately. Take the tool to an author-

ized service center.

• Always hold the handle with one hand and the

front grip with the other. (See Fig.4) Maintain a

firm grip and depress the switch fully.

• The blade should not touch the cutting mate-

rial before you start the motor. Wait until the

blade reaches full speed before starting a cut.

• This tool has no provision to lock the power

switch in the “ON” position, and you must not

attempt to secure it in the “ON” position.

3.Start cutting when the blade reaches full

speed.

4.During cutting, keep your cutting line straight.

Move the metal cutter forward at a steady

speed, while looking at the tip of the blade

through the transparent guard.

-

13

-

WARNING

• To prevent dangerous kickback, keep the

shoe of the metal cutter flat on the surface of

the material being cut.

• Never force the cutter. Use light and continu-

ous pressure.

5.If the motor starts to feel too warm, stop cut-

ting. Let the metal cutter cool down before

continuing work.

6.It is always a safe practice to remove the

battery pack after use and before storing the

metal cutter.

Cutting depth adjustment

•Remove battery pack.

•Loosen the depth adjustment lever by pushing it

and adjust the cutting depth.

Tighten the depth adjustment lever securely by

lifting it up towards the motor housing at the

desired cutting depth. (See Fig.5)

Rip fence (EY3500B7727)

(Available as an accessory, not included)

Rip fence is convenient for rip cuts and repeated

cuts of uniform width.

•Remove battery pack.

•Insert rip fence and adjust cutting width. (See

Fig.6)

•Fasten screw securely to fix rip fence.

For Proper Use (Further Detail)

WARNING

To prevent the risk of serious personal injury:

l It is important to use an appropriate device

to hold the material being cut properly, and

to hold the cutter firmly with both hands to

prevent loss of control which could cause

personal injury.

• Figure 7 shows proper cutting position.

• Note that hands are kept away from cutting

area.

• Make sure bystanders are away from work

area and from underneath of workpiece.

• When cutting, do not try to hold the material

with your hand.

Cutting large sheets;

Support large sheets. Be sure to set the depth

of the cut so that you only cut through the

workpiece, not through the supports. (See

Fig.8)

Large sheets sag or bend if they are not

correctly supported. If you attempt to cut

without leveling and properly supporting the

workpiece, the blade will tend to bind, causing

kickback. (See Fig.9)

• Don’t support the material away from the

cut.

Cutting thin or corrugated materials;

Cut thin and corrugated materials at least

1" from the edge of the workpiece to avoid

injury or damage to the tool caused by thin

strips of metal being pulled into the upper

guard.

•Use sharp blades only. Clean and sharp

blades minimize stalling and kickback.

WARNING

To prevent the risk of serious personal injury:

• When making an incomplete cut or cutting

is interrupted, or blade is binding or cutter is

stalling; release the power switch immediately

and hold the cutter motionless in the material

until the blade comes to a complete stop.

• To avoid kickback, never attempt to remove

the cutter from the work or pull the cutter

backward while the blade is in motion. Make

sure the blade has come to a complete stop,

then remove cutter from cut.

• To resume cutting, start metal cutter, allow

the blade to reach full speed, reenter the cut

slowly and resume cutting.

-

14

-

1.Place the wider part of the shoe on the part of

the work piece which is solidly supported (See

Fig.10), never on the section that will fall off

when the cut is made. (See Fig.11)

Hold the cutter firmly to prevent loss of control.

Working carelessly can cause severe personal

injury.

2.Make sure the blade stops.

Even though your metal cutter has a brake,

before setting the metal cutter down, make

sure the blade has come to a complete stop

and the lower guard has closed.

3.Do not use if anything seems unusual. Remove

battery pack immediately.

If the metal cutter body becomes very hot, or

does not work properly, remove the battery

pack and do not use. Have it checked by an

authorized service center.

WARNING

To prevent the risk of serious personal injury

or fire, do not try to repair the metal cutter

by yourself. Never disassemble or modify the

metal cutter body. There are no user-repair-

able parts inside.

4.NEVER ALLOW THE CUTTER TO COME IN

CONTACT WITH YOUR BODY.

After completing a cut, do not allow the cutter

to brush against your leg or side.

Since the lower guard is retractable, it could

catch on your clothing and expose the blade.

Keep clothing away from metal cutter. Be

aware of the exposed blade sections that exist

in both the upper and lower guard areas.

WARNING

Because cutting metal creates sparks;

• Always use safety goggles.

• Do not use metal cutter near any flammable

substance or in an area where flammable

substances are used. Fire and burn injury

could result.

5.Never engage the spindle lock while blade is

running, or engage in an effort to stop the tool.

Never turn the switch on when the spindle lock

is engaged. Serious damage to your metal cut-

ter will result.

V. MAINTENANCE

WARNING

To avoid severe personal injury, always

remove the battery pack from the metal cutter

before starting any maintenance procedure.

CAUTION:

To assure product SAFETY and RELIABILITY,

servicing should be performed by an authorized

service center. Always insist on genuine Panasonic

replacement parts.

Removing Blade

CAUTION:

The blade will be hot right after cutting. Be sure to

let the blade cool down before removing it.

Follow these steps:

1.Remove the battery pack from the metal cutter.

2.Hold the spindle lock button down. This pre-

vents the blade from rotating.

3.Use the provided hex wrench to loosen the hex

bolt.

NOTE:

Keep the hex wrench in the storage slot on the

metal cutter’s body when not using it.

4.Remove the hex bolt and outer washer.

5.Use the lower guard lift lever to retract (open)

the lower guard.

6.Carefully remove the blade.

7.Clean the metal cutter if necessary.

CAUTION:

Be careful to avoid cutting your hands on the

blade.

• When disposing of a blade, secure it inside

heavy or corrugated paper. This will help pre-

vent anyone from being cut by the discarded

blade.

-

15

-

Installing Blade

Follow these steps:

1.Remove the battery pack from the metal cutter.

2.Remove any cutting debris from blade area.

3.Use the lower guard lift lever to retract (open)

the lower guard.

4.Install the blade as illustrated. (See Fig.12)

Make sure that both the direction arrow on the

blade and the direction arrow on the upper

blade cover point in the same direction.

5.Set the outer washer in place.

6.Insert the hex bolt.

7.Hold the spindle lock button down. This pre-

vents the blade from rotating.

8.Tighten the hex bolt securely with the provided

hex wrench. Store the hex wrench.

NOTE:

Keep the hex wrench in the storage slot on the

metal cutter’s body when not using it.

WARNING

Failure to follow these instructions can result

in serious personal injury.

For Appropriate use of Battery

pack

Ni-MH Battery pack (EY9251)

• Charge the Ni-MH battery fully before storage

in order to ensure a longer service life.

• The ambient temperature range is between 0°C

(32°F) and 40°C (104°F).

If the battery pack is used when the battery

temperature is below 0°C (32°F), the tool may

fail to function properly. In that case, charge the

battery until charging is completed for appropri-

ate functioning of the battery.

• When battery pack is not in use, keep it away

from other metal objects like: paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause sparks, burns or a fire.

• When operating with a Ni-MH battery pack,

make sure the place is well ventilated.

Battery Pack Life

The rechargeable batteries have a limited life. If

operation time becomes extremely short after

recharging, replace the battery pack with a new one.

NOTE:

•Use under extremely hot or cold conditions will

reduce operating capacity per charge.

•Even if you don’t use the Metal Cutter, charge

the battery pack at least once every six months.

Battery Recycling

ATTENTION:

•For environmental protection and recycling of

materials, be sure that it is disposed of at an

officially assigned location, if there is one in your

country.

Cleaning Metal Cutter

Keep your metal cutter clean for good cutting per-

formance, and to help keep it safe to use.

Follow these steps:

1.Remove the battery pack from the metal cutter.

2.Wipe the metal cutter with a dry, soft cloth. Do

not use a wet cloth or cleaning liquids.

They could damage the metal cutter’s finish.

3.Be sure to rub off any oil or grease which

could make the metal cutter slippery or hard to

handle.

4.Remove the blade and brush off any dust.

CAUTION:

To avoid injury or damage to the unit, never

immerse any part of the tool in a liquid.

Transparent Guard

WARNING

If the guard is cracked, or is broken, take the

metal cutter to an authorized service center

for replacement. Do not attempt to operate

cutter. It could result in serious personal injury.

Never use your metal cutter with a damaged

transparent guard or without the transparent

guard installed. Flying chips could result in

serious injury.

-

16

-

VI. ACCESSORIES

WARNING

•The use of any accessories not specified in

this manual may result in fire, electric shock,

or personal injury. Use recommended acces-

sories only.

•Use of a blade on material that is thicker or

thinner than that recommended for that blade

will result in a rough cut, and could increase

the risk of “kickback

” or other injury.

Blade for cutting metal material

•EY9PM17A

For cutting unhardened ferrous material

Thickness of material

0.3 mm - 6.0 mm (1/64" - 15/64")

Blade for cutting thin metal material (Optional

accessory)

•EY9PM17B

For cutting unhardened thin ferrous material

Thickness of material

0.3 mm - 2.0 mm (1/64" - 5/64")

Rip Fence (Optional accessory)

•EY3500B7727

For convenience of rip cuts and repeated cut of

uniform width

Battery Pack

•EY9251

Battery Charger

•EY0110

VII.SPECIFICATIONS

Metal Cutter (EY3552)

Motor voltage 18 V DC

Blade Speed 2900 /min (rpm)

Blade Size

Outside diameter

Arbor size

165 mm (6-1/2")

20 mm (25/32")

Maximum cutting depth

3 - 56 mm (1/8" - 2-13/64") (

φ

165mm blade)

Dimensions (L × W × H)

345 × 198 × 264 mm

(13-37/64" × 7-51/64" × 10-25/64")

Weight (with battery pack) 4 kg (8.82lbs)

Battery Pack (EY9251)

Storage Battery Ni-MH Battery

Voltage 18 V DC (1.2 V × 15 cells)

Battery Charger (EY0110)

Model EY0110

Electrical rating See the rating plate on the bottom of the charger.

Weight 0.78 kg (1.72 lbs)

Charging time 65 minutes (EY9251)

NOTE:

• Do not charge “Y” type Ni-Cd battery packs.

• For applicable battery packs to this charger, see the label on the charger or the latest general

catalog.

-

17

-

ONLY FOR U. K.

VIII.

ELECTRICAL PLUG

INFORMATION

FOR YOUR SAFETY PLEASE READ

THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded

three pin mains plug for your safety and

convenience.

A 3 amp fuse is tted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rat

-

ing of 3 amp and that it is approved by ASTA

or BSI to BS1362.

Check for the ASTA mark

or the BSI

mark on the body of the fuse.

If the plug contains a removable fuse cover

you must ensure that it is retted when the

fuse is replaced.

If you lose the fuse cover the plug must

not be used until a replacement cover is

obtained.

A replacement fuse cover can be purchased

from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS

UNSUITABLE FOR THE SOCKET

OUTLET IN YOUR HOME THEN THE

FUSE SHOULD BE REMOVED AND THE

PLUG CUT OFF AND DISPOSED OF

SAFELY.

THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF

PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be tted please observe

the wiring code as shown below.

If in any doubt please consult a qualied

electrician.

IMPORTANT:

The wires in this mains lead are coloured

in accordance with the following code:

Blue:Neutral

Brown: Live

As the colours of the wire in the mains lead

of this appliance may not correspond with

the coloured markings identifying the termi-

nals in your plug, proceed as follows.

The wire which is coloured BLUE must be

connected to the terminal in the plug which

is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be

connected to the terminal in the plug which is

marked with the letter L or coloured RED.

Under no circumstances should either of

these wires be connected to the earth ter-

minal of the three pin plug, marked with the

letter E or the Earth Symbol .

How to replace the fuse: Open the fuse

compartment with a screwdriver and re-

place the fuse and fuse cover if it is remov-

able.

Fuse Cover

This apparatus was produced to BS800.

Page is loading ...

Matsushita Electric Works, Ltd.

Osaka, Japan

No.1 EN. GR. FR. IT. ND. ES. DN. SW. NR. FN. RUS. Uk

EY971035522 H1705 Printed in Japan

Panasonic EY3552GQW Owner's manual

This manual is also suitable for

Panasonic EY3552GQW Owner's manual

in other languages

Related papers

Other documents