ADTRAN Atlas 800 User manual

ATLAS 800

PLUS

User Manual

Part Number 1200226L1

Part Number 1200228L1

61200226L1-1C

May 2000

TRADEMARKS

Windows is a registered trademark of Microsoft Corporation.

DMS 100 is a registered trademark of Northern Telecom.

5ESS is a registered trademark of AT&T.

AT&T is a registered trademark.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

iii

FCC regulations require that in this manual the following information be provided to the

customer:

1. This equipment complies with Part 68 of the FCC rules. The required label is affixed to the bottom

of the chassis.

2. An FCC-compliant telephone cord and modular plug is provided with this equipment. This equip-

ment is designed to be connected to the telephone network or premises wiring using a compatible

modular jack which is Part 68-compliant. See Chapter 2, Installing the ATLAS 800PLUS, for details.

3. If your telephone equipment (ATLAS) causes harm to the telephone network, the telephone com-

pany may discontinue your service temporarily. If possible, they will notify you in advance. But

if advance notice isn’t practical, you will be notified as soon as possible. You will be advised of your

right to file a complaint with the FCC.

4. Your telephone company may make changes in its facilities, equipment, operations, or procedures

that could affect the proper operation of your equipment. If they do, you will be given advance

notice to give you an opportunity to maintain uninterrupted service.

5. If you experience trouble with this equipment (ATLAS), please contact ADTRAN at (256) 963-8000

for repair/ warranty information. The telephone company may ask you to disconnect this equip-

ment from the network until the problem has been corrected or until you are sure the equipment is

not malfunctioning.

6. This unit contains no user-serviceable parts.

7. The following information may be required when applying to your local telephone company for

leased line facilities.

Service Type REN/SOC FIC USOC

1.544 Mbps - SF 6.0N 04DU9-BN RJ-48C

1.544 Mbps - SF and B8ZS 6.0N 04DU9-DN RJ-48C

1.544 Mbps - ESF 6.0N 04DU9-1KN RJ-48C

1.544 Mbps - ESF and B8ZS 6.0N 04DU9-1SN RJ-48C

ISDN 6.0N 04DU9-ISN RJ-48C

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pur-

suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio frequencies. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Change or modifications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital terminal equipment

without encoded analog content and billing protection is used to transmit digital signals contain-

ing encoded analog content which are intended for eventual conversion into voiceband analog sig-

nals and transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing information is being

transmitted or that the output of the device meets Part 68 encoded analog content or billing protec-

tion specifications.

• End user/customer will be responsible for filing an affidavit with the local exchange carrier when

connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital ser-

vices.

• Until such time as subrate digital terminal equipment is registered for voice applications, the affi-

davit requirement for subrate services is waived.

Affidavit for Connection of Customer Premises Equipment

to 1.544 Mbps and/or Subrate Digital Services

For the work to be performed in the certified territory of ________________________(telco name)

State of ________________

County of ________________

I, _____________________________ (name), __________________________________(business address),

____________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to

1.544 Mbps and/or ________ subrate digital services. The terminal equipment to be connected com-

plies with Part 68 of the FCC rules except for the encoded analog content and billing protection speci-

fications. With respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the

digital CPE with respect to analog content and encoded billing protection information continu-

ously complies with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog content or billing

information which is intended to be decoded within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not under the control of the

customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, mainte-

nance, and adjustment of the encoded analog content and billing information has (have) been trained

to perform these functions by successfully having completed one of the following (check appropriate

blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode

analog signals; or

( ) B. A training course provided by the customer or authorized representative, using training mate-

rials and instructions provided by the manufacturer/grantee of the equipment used to encode

analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) recognized by the

manufacturer/grantee of the equipment used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the

control of a supervisor trained in accordance with _________ (circle one) above.

vii

I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate

compliance with the information as provided in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of ________, 199___

_________________________________

Notary Public

My commission expires:

_________________________________

viii

Canadian Equipment Limitations

Before installing this equipment, users should ensure that it is permissible to be connected to the facil-

ities of the local telecommunications company. The equipment must also be installed using an accept-

able method of connection. In some cases, the company's inside wiring associated with a single line

individual service may be extended by means of a certified connector assembly (telephone extension

cord). The customer should be aware that compliance with the above conditions may not prevent deg-

radation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility desig-

nated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground connections of the power util-

ity, telephone lines and internal metallic waterpipe system, if present, are connected together. This

precaution may be particularly important in rural areas.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be

connected to a telephone loop which is used by the device, to prevent overloading. The termination

on a loop may consist of any combination of devices subject only to the equipment that the total of the

LNs of all devices does not exceed 100.

The ringer equivalence number (REN) assigned to each terminal adapter is used to determine the total

number of devices that may be connected to each circuit. The sum of the RENs from all devices in the

circuit should not exceed a total of 5.0.

The Industry Canada Certification label identifies certified equipment. This certification means that

the equipment meets certain telecommunications network protective, operational, and safety

requirements. The Department does not guarantee the equipment will operate to the user's

satisfaction.

Users should not attempt to make such connections themselves, but should contact the appropriate

electric inspection authority, or an electrician, as appropriate.

LIMITED PRODUCT WARRANTY

ADTRAN warrants that for five (5) years from the date of shipment to Customer, all products manu-

factured by ADTRAN will be free from defects in materials and workmanship. ADTRAN also war-

rants that products will conform to the applicable specifications and drawings for such products, as

contained in the Product Manual or in ADTRAN's internal specifications and drawings for such prod-

ucts (which may or may not be reflected in the Product Manual). This warranty only applies if Cus-

tomer gives ADTRAN written notice of defects during the warranty period. Upon such notice,

ADTRAN will, at its option, either repair or replace the defective item. If ADTRAN is unable, in a rea-

sonable time, to repair or replace any equipment to a condition as warranted, Customer is entitled to a

full refund of the purchase price upon return of the equipment to ADTRAN. This warranty applies

only to the original purchaser and is not transferable without ADTRAN's express written permission.

This warranty becomes null and void if Customer modifies or alters the equipment in any way, other

than as specifically authorized by ADTRAN.

EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING CONSTITUTES

THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE EXCLUSIVE LIABILITY OF

ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES (EXPRESSED OR IMPLIED).

ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING (WITHOUT LIM-

ITATION), ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THIS

EXCLUSION MAY NOT APPLY TO CUSTOMER.

In no event will ADTRAN or its suppliers be liable to Customer for any incidental, special, punitive,

exemplary or consequential damages experienced by either Customer or a third party (including, but

not limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for

damages for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the

amount paid for the item. Some states do not allow the limitation or exclusion of liability for inciden-

tal or consequential damages, so the above limitation or exclusion may not apply to Customer.

About this Manual

The ATLAS 800

PLUS

system consists of the Base Unit and one or more option modules. (Each option

module includes its own user manual which contains specific information about installing, configur-

ing, and testing the option module; insert the option module manuals into this binder.) This ATLAS

User Manual provides the information you need to install, configure, test, and troubleshoot the

ATLAS 800

PLUS

system; when applicable, this manual refers you to the individual option module user

manual. The arrangement of this user manual allows you to quickly and easily find the information

you need. An overview of the contents of this manual follows:

Introduction

• Chapter 1, Introducing the ATLAS 800PLUS, familiarizes you with the ATLAS 800

PLUS

Base Unit

and provides some sample ATLAS 800

PLUS

applications.

Getting Started

• Chapter 2, Installing the ATLAS 800PLUS, describes the rear panel layout and how to install the

ATLAS 800

PLUS

• Chapter 3, Operating the ATLAS 800PLUS, describes the front panel layout and different ways to op-

erate the ATLAS 800

PLUS

Reference Information

• Chapter 4, Using the Front Panel, describes how to use the front panel. This chapter also describes

each menu option that is accessible through the front panel.

• Chapter 5, Navigating the Terminal Menu, describes how to navigate the terminal menu.

• Chapter 6, Terminal Menu and System Control, describes the terminal menus used for system control.

• Chapter 7, Modules Terminal Menu, describes the terminal menus used for module and T1/PRI port

control.

• Chapter 8, Dedicated Maps Terminal Menu, describes the terminal menus used for Dedicated Maps

and provides some examples.

• Chapter 9, Dedicated Circuit Backup and Circuit Status, describes the terminal menus used for Circuit

Status.

• Chapter 10, Dial Plan Terminal Menu, describes the terminal menus used for Dial Plans and provides

some examples.

Working with the ATLAS 800

PLUS

• Chapter 11, Updating Firmware, provides step-by-step instruction on how to update the

ATLAS 800

PLUS

firmware.

• Chapter 12, SNMP Management, describes how to control the ATLAS 800

PLUS

via SNMP.

• Chapter 13, ADTRAN Utilities, describes the SysLog, Telnet, VT-100, and TFTP Server programs de-

livered with the ATLAS 800

PLUS

Appendices

• Appendix A, System Event Logging, describes the events monitored by the ATLAS 800

PLUS

• Appendix B, Troubleshooting, describes how to diagnose different problems you may experience.

• Appendix C, Warranty and Technical Support Information, describes your warranty and how to con-

tact technical support.

• Appendix D, Acronyms and Abbreviations, lists acronyms and abbreviations used for the

ATLAS 800

PLUS

and its option modules.

• Appendix E, Glossary, defines terms used with ATLAS 800

PLUS

and its option modules.

Notes provide additional useful information.

Cautions signify information that could prevent service interruptions.

Warnings provide information that could prevent damage to the equipment or

endangerment to human life.

xii

61200226L1-1 ATLAS 800

PLUS

User Manual xiii

Table of Contents

List of Figures....................................................................................................................... xxiii

List of Tables.......................................................................................................................... xxv

Chapter 1 Introducing the ATLAS 800PLUS........................................................................................1-1

Product Overview......................................................................................................................................... 1-1

ATLAS 800PLUS Base Unit ......................................................................................................................... 1-1

ATLAS 800PLUS Features........................................................................................................................... 1-6

Chapter 2 Installing the ATLAS 800PLUS............................................................................................2-1

Inspect the ADTRAN Shipment................................................................................................................. 2-1

Contents of ADTRAN Shipments............................................................................................................... 2-1

Check the Power Connection...................................................................................................................... 2-1

AC Powered Unit....................................................................................................................................2-2

DC Powered Unit....................................................................................................................................2-2

Grounding Instructions................................................................................................................................ 2-2

Review the Rear Panel Design .................................................................................................................... 2-3

Control/Chain In Port ...........................................................................................................................2-4

Connection....................................................................................................................................... 2-4

Control/Chain Out Port........................................................................................................................2-5

Connection....................................................................................................................................... 2-5

Network Connection..............................................................................................................................2-6

Connection....................................................................................................................................... 2-6

Ethernet 10BaseT Connection...............................................................................................................2-7

Connection....................................................................................................................................... 2-7

MON.........................................................................................................................................................2-7

Option Slots .............................................................................................................................................2-7

Install Any Option Modules........................................................................................................................ 2-8

Power-Up....................................................................................................................................................... 2-8

Chapter 3 Operating the ATLAS 800PLUS...........................................................................................3-1

Methods of Operating the ATLAS 800PLUS ............................................................................................ 3-1

Using the Front Panel................................................................................................................................... 3-1

Using The Terminal Menu........................................................................................................................... 3-2

Using Telnet.............................................................................................................................................3-3

Starting a Telnet Session................................................................................................................ 3-4

Using VT-100 Terminal Emulation ......................................................................................................3-4

Using T-Watch PRO ...............................................................................................................................3-5

Chapter 4 Using the Front Panel.............................................................................................................4-1

Operation Keys.............................................................................................................................................. 4-4

Front Panel Menu Structure........................................................................................................................ 4-4

Front Panel Main Menu ............................................................................................................................... 4-6

Menus ............................................................................................................................................................. 4-7

Table of Contents

xiv ATLAS 800

PLUS

User Manual 61200226L1-1

Submenus ............................................................................................................................................... 4-7

Sub-submenus ................................................................................................................................ 4-7

Status.............................................................................................................................................................. 4-7

S0 System ................................................................................................................................................ 4-7

Ethernet Status ............................................................................................................................... 4-7

Chain Port Status ........................................................................................................................... 4-7

S1—S8 ..................................................................................................................................................... 4-7

Config............................................................................................................................................................. 4-7

S0 System ................................................................................................................................................ 4-7

Ethernet ........................................................................................................................................... 4-8

Chain Port ....................................................................................................................................... 4-8

S1—S8 ..................................................................................................................................................... 4-9

Util.................................................................................................................................................................. 4-9

Time/Date .............................................................................................................................................. 4-9

Software Rev .......................................................................................................................................... 4-9

Selftest ................................................................................................................................................... 4-10

Run Selftest ................................................................................................................................... 4-10

Show Results ................................................................................................................................ 4-10

Clear Results ................................................................................................................................. 4-11

Set Passcode ......................................................................................................................................... 4-11

Password Reset .................................................................................................................................... 4-11

ALRM Menu............................................................................................................................................... 4-11

Active Alarms ...................................................................................................................................... 4-11

View History ........................................................................................................................................ 4-12

Clear History ........................................................................................................................................ 4-12

Chapter 5 Navigating the Terminal Menu............................................................................................5-1

Terminal Menu Window............................................................................................................................. 5-1

Menu Path................................................................................................................................................5-1

Window Panes.........................................................................................................................................5-2

Window Pane Navigation ............................................................................................................ 5-2

Right Window Pane Notation...................................................................................................... 5-2

Additional Terminal Menu Window Features...................................................................................5-3

Navigating Using the Keyboard Keys ...................................................................................................... 5-3

Moving through the Menus ..................................................................................................................5-3

Session Management Keystrokes .........................................................................................................5-4

Configuration Keystrokes......................................................................................................................5-4

Getting Help ............................................................................................................................................5-5

Chapter 6 Terminal Menu and System Control...................................................................................6-1

Selecting the Appropriate menu................................................................................................................ 6-1

Security Levels.............................................................................................................................................. 6-2

Menus............................................................................................................................................................. 6-2

Submenus ............................................................................................................................................... 6-2

Sub-submenus ................................................................................................................................ 6-2

System Info.................................................................................................................................................... 6-2

System Name ......................................................................................................................................... 6-3

System Location .................................................................................................................................... 6-3

System Contact ...................................................................................................................................... 6-3

Firmware Revision ................................................................................................................................ 6-3

System Uptime ...................................................................................................................................... 6-3

Startup Mode ......................................................................................................................................... 6-3

Current Time/Date (24h) ..................................................................................................................... 6-3

Installed Memory .................................................................................................................................. 6-3

Table of Contents

61200226L1-1 ATLAS 800

PLUS

User Manual xv

Serial Number ........................................................................................................................................6-3

Boot ROM Rev ........................................................................................................................................6-3

System Status................................................................................................................................................. 6-3

Event Log ................................................................................................................................................6-4

Clear System Event Log ........................................................................................................................6-4

Ethernet Port ...........................................................................................................................................6-5

Clear System LED ..................................................................................................................................6-5

System Alarms .......................................................................................................................................6-5

System Timing Source ...........................................................................................................................6-5

Resource Usage ......................................................................................................................................6-5

Data Tables .............................................................................................................................................6-5

Configuration .........................................................................................................................................6-6

Trunk Usage ...........................................................................................................................................6-6

Data Tables .............................................................................................................................................6-6

Chain Port Signal Leads ........................................................................................................................6-6

Chain Port Tx Bytes ...............................................................................................................................6-7

Chain Port Rx Bytes ...............................................................................................................................6-7

Chain Port Overrun Errs .......................................................................................................................6-7

Chain Port Framing Errs .......................................................................................................................6-7

Clear Chain Port Countrs .....................................................................................................................6-7

System Config................................................................................................................................................ 6-7

Primary Timing Source .........................................................................................................................6-7

Backup Timing Source ..........................................................................................................................6-7

ADLP Address .......................................................................................................................................6-7

Session Timeout .....................................................................................................................................6-8

Max Telnet Sessions ...............................................................................................................................6-8

Ethernet Port ...........................................................................................................................................6-8

Chain Port ...............................................................................................................................................6-8

Port Name ........................................................................................................................................6-8

Port Type ..........................................................................................................................................6-9

Port Speed ........................................................................................................................................6-9

Modem Initialization String ..........................................................................................................6-9

Initialize Modem .............................................................................................................................6-9

Flow Control ....................................................................................................................................6-9

SNMP .......................................................................................................................................................6-9

SNMP Access ..................................................................................................................................6-9

SNMP Communities ......................................................................................................................6-9

Trap Transmission ..........................................................................................................................6-9

Authen Trap Transmission ...........................................................................................................6-9

Traps Destination .........................................................................................................................6-10

System Event Logging ........................................................................................................................6-10

Syslog Setup ..........................................................................................................................................6-10

Transmission .................................................................................................................................6-10

Host IP Address ............................................................................................................................6-10

Host Facility ...................................................................................................................................6-10

Real Time Clock ...................................................................................................................................6-10

Current Time/Date ......................................................................................................................6-10

Auto Daylight Savings .................................................................................................................6-10

Access Passwords ................................................................................................................................6-11

Label ...............................................................................................................................................6-11

Access Rights .................................................................................................................................6-11

Password ........................................................................................................................................6-11

Active ..............................................................................................................................................6-12

Bonding Config ....................................................................................................................................6-12

Table of Contents

xvi ATLAS 800

PLUS

User Manual 61200226L1-1

TXINIT Timer ............................................................................................................................... 6-12

TXFA Timer .................................................................................................................................. 6-12

TXADD01 Timer .......................................................................................................................... 6-12

TXDEQ Timer ............................................................................................................................... 6-12

TANULL Timer ............................................................................................................................ 6-12

TCID Timer ................................................................................................................................... 6-13

Call Stagger ................................................................................................................................... 6-13

System Utility ............................................................................................................................................. 6-13

Update Firmware ................................................................................................................................ 6-13

Module Slot ................................................................................................................................... 6-14

Module Type ................................................................................................................................ 6-14

Transfer Method .......................................................................................................................... 6-14

Restart Schedule ........................................................................................................................... 6-14

Current Update Status ................................................................................................................ 6-15

Previous Update Status ............................................................................................................... 6-15

Begin Firmware Update .............................................................................................................. 6-15

Update Status ...................................................................................................................................... 6-16

Config Transfer .................................................................................................................................... 6-16

Transfer Method .......................................................................................................................... 6-16

TFTP Server IP Address .............................................................................................................. 6-16

TFTP Server Filename ................................................................................................................. 6-16

Current Transfer Status ............................................................................................................... 6-16

Previous Transfer Status ............................................................................................................. 6-16

Load and Use Config ................................................................................................................... 6-17

Save Config Remotely ................................................................................................................. 6-17

System Utilization ............................................................................................................................... 6-17

System Selftest ..................................................................................................................................... 6-17

Selftest Run ................................................................................................................................... 6-17

Status ............................................................................................................................................. 6-17

View Selftest Log ......................................................................................................................... 6-17

Clear Self-test Log ........................................................................................................................ 6-18

Ping ....................................................................................................................................................... 6-19

IP Address ..................................................................................................................................... 6-19

Count ............................................................................................................................................. 6-19

Size ................................................................................................................................................. 6-19

Timeout ......................................................................................................................................... 6-19

Round trip min ............................................................................................................................. 6-19

Round trip avg ............................................................................................................................. 6-19

Round trip max ............................................................................................................................ 6-19

Tx Stats .......................................................................................................................................... 6-19

Reset Stats ..................................................................................................................................... 6-19

Start/Stop ...................................................................................................................................... 6-19

Reboot System ..................................................................................................................................... 6-20

Factory Default System ...................................................................................................................... 6-20

Chapter 7 Modules Terminal Menu.......................................................................................................7-1

Menus............................................................................................................................................................. 7-1

Submenus ............................................................................................................................................... 7-1

Sub-submenus ................................................................................................................................ 7-1

Modules......................................................................................................................................................... 7-1

Slt ............................................................................................................................................................. 7-1

Type ........................................................................................................................................................ 7-2

Menu ....................................................................................................................................................... 7-2

Alarm ...................................................................................................................................................... 7-2

Table of Contents

61200226L1-1 ATLAS 800

PLUS

User Manual xvii

Test ...........................................................................................................................................................7-2

State ..........................................................................................................................................................7-2

Status .......................................................................................................................................................7-3

Rev ...........................................................................................................................................................7-3

Modules (Quad T1/PRI) Menu ............................................................................................................7-3

Controller Info .................................................................................................................................7-3

Alarm Status ....................................................................................................................................7-3

DS0 Status ........................................................................................................................................7-4

DS0 Alarms ......................................................................................................................................7-4

Sig Status ..........................................................................................................................................7-4

Performance: Current .....................................................................................................................7-5

Performance: 15 Min ......................................................................................................................7-5

Performance: 24 Hr. ........................................................................................................................7-5

Configuration ..................................................................................................................................7-5

Test ....................................................................................................................................................7-6

Chapter 8 Dedicated Maps Terminal Menu.........................................................................................8-1

Overview........................................................................................................................................................ 8-1

Menus ............................................................................................................................................................. 8-1

Submenus ................................................................................................................................................8-1

Sub-submenus .................................................................................................................................8-1

Activate Map ................................................................................................................................................. 8-2

Auto .........................................................................................................................................................8-2

Maps 1—5 ...............................................................................................................................................8-2

Current Map .................................................................................................................................................. 8-2

Create / Edit Maps ....................................................................................................................................... 8-2

# ................................................................................................................................................................8-2

Map Name ..............................................................................................................................................8-2

Sort TO/FROM ......................................................................................................................................8-2

Connects ..................................................................................................................................................8-2

# .........................................................................................................................................................8-3

FROM Slt ..........................................................................................................................................8-3

Port ....................................................................................................................................................8-3

TO Slot ..............................................................................................................................................8-3

Port ....................................................................................................................................................8-3

From Config ....................................................................................................................................8-3

To Config .........................................................................................................................................8-5

RBS ....................................................................................................................................................8-5

Activate Time .........................................................................................................................................8-5

Enbl Day ..................................................................................................................................................8-5

Designing a Dedicated map..................................................................................................................8-6

Configuring the Ports.............................................................................................................................8-7

Defining the Connections......................................................................................................................8-8

Chapter 9 Dedicated Circuit Backup and Circuit Status....................................................................9-1

Overview........................................................................................................................................................ 9-1

Dedicated Circuit Dial Backup Setup..................................................................................................9-1

Configuration.................................................................................................................................. 9-2

Menus ............................................................................................................................................................. 9-2

Submenus ................................................................................................................................................9-2

Sub-submenus .................................................................................................................................9-2

Interface Configuration................................................................................................................................ 9-3

Originate/Answer .................................................................................................................................9-3

Outgoing Call Type ...............................................................................................................................9-3

Table of Contents

xviii ATLAS 800

PLUS

User Manual 61200226L1-1

Source ID ................................................................................................................................................ 9-3

Outdial Number .................................................................................................................................... 9-3

Force Mode ............................................................................................................................................ 9-3

Backup Criteria ...................................................................................................................................... 9-3

Restore Criteria ...................................................................................................................................... 9-3

Startup Delay ......................................................................................................................................... 9-3

Backup Delay ......................................................................................................................................... 9-3

Restore Delay ......................................................................................................................................... 9-4

Max Num Redials ................................................................................................................................. 9-4

Redial Timer .......................................................................................................................................... 9-4

Enable Schedule .................................................................................................................................... 9-4

Test Call .................................................................................................................................................. 9-4

Min Num DS0s ...................................................................................................................................... 9-4

Max Num DS0s ..................................................................................................................................... 9-4

Circuit Status Menu..................................................................................................................................... 9-5

From............................................................................................................................................................... 9-5

MAN (Manual Backup)............................................................................................................................... 9-5

BKUP Status (Backup Status) ..................................................................................................................... 9-6

Line Status..................................................................................................................................................... 9-6

Delay .............................................................................................................................................................. 9-6

Test ................................................................................................................................................................. 9-7

Last Run Time ........................................................................................................................................ 9-7

Next Run Time ...................................................................................................................................... 9-7

Last Test Status ...................................................................................................................................... 9-7

Pass : Fail ................................................................................................................................................ 9-7

Test Now ................................................................................................................................................ 9-7

Chapter 10 Dial Plan Terminal Menu....................................................................................................10-1

Overview..................................................................................................................................................... 10-1

Network Term ............................................................................................................................................ 10-3

Slot/Svc ................................................................................................................................................ 10-3

Port/PEP .............................................................................................................................................. 10-3

Sig .......................................................................................................................................................... 10-3

Out#Accept .......................................................................................................................................... 10-3

Src ID ............................................................................................................................................. 10-3

Accept Numbers .......................................................................................................................... 10-4

Search ............................................................................................................................................. 10-4

Data 64K, Data 56K ...................................................................................................................... 10-4

Out#Rej ................................................................................................................................................. 10-4

Reject Number .............................................................................................................................. 10-5

Data 64K, Data 56K, Audio, and Speech .................................................................................. 10-5

Ifce Config ............................................................................................................................................ 10-5

User Term.................................................................................................................................................... 10-5

Slot/Svc, Port/PEP ............................................................................................................................. 10-5

Sig .......................................................................................................................................................... 10-5

In#Accept .............................................................................................................................................. 10-6

Source ID ....................................................................................................................................... 10-6

Accept Numbers .......................................................................................................................... 10-6

Search ............................................................................................................................................. 10-6

Data 64K, Data 56K ...................................................................................................................... 10-7

Out#Rej ................................................................................................................................................. 10-7

Reject Number .............................................................................................................................. 10-7

Data 56K, Data 64K, Audio, Speech .......................................................................................... 10-7

Ifce Config ............................................................................................................................................ 10-7

Table of Contents

61200226L1-1 ATLAS 800

PLUS

User Manual xix

Global Param............................................................................................................................................... 10-8

End of Number Timeout .....................................................................................................................10-8

Area Code .............................................................................................................................................10-8

Nbr Complete Templates ....................................................................................................................10-8

Number Type Templates ....................................................................................................................10-8

Automatic Routeback Rejection .........................................................................................................10-9

Quad T1/PRI Module Interface Configuration...................................................................................... 10-9

Quad T1/PRI Module (Network Termination/PRI).......................................................................10-9

Switch Type ...................................................................................................................................10-9

First DS0 .........................................................................................................................................10-9

Number of DS0s ..........................................................................................................................10-10

Outgoing Number Conversion .................................................................................................10-10

Strip MSD .....................................................................................................................................10-10

Netwrk Spec. Fac. - Voice ..........................................................................................................10-10

Netwrk Spec. - Fac. Data ...........................................................................................................10-10

Called Digits Transferred ..........................................................................................................10-10

Outgoing Caller ID .....................................................................................................................10-11

Source ID ......................................................................................................................................10-11

Swap ANI/DNIS ........................................................................................................................10-11

Quad T1/PRI Module (Network Termination/RBS).......................................................................... 10-12

First DS0 .......................................................................................................................................10-12

Number of DS0s ..........................................................................................................................10-12

DS0s Available ............................................................................................................................10-12

Signaling Method .......................................................................................................................10-12

Direct Inward Dialing ................................................................................................................10-13

Trunk Number ............................................................................................................................10-13

Strip MSD .....................................................................................................................................10-13

Source ID ......................................................................................................................................10-13

Quad T1/PRI Module (User Termination/PRI) .................................................................................. 10-14

Switch Type .................................................................................................................................10-14

First DS0 .......................................................................................................................................10-14

Number of DS0s ..........................................................................................................................10-14

Strip MSD ............................................................................................................................................10-14

Network Specific Facility Voice .......................................................................................................10-14

Network Specific Facility Data ........................................................................................................10-14

Called Digits Transferred ..........................................................................................................10-15

Outgoing Caller ID .....................................................................................................................10-15

ID Presentation ...................................................................................................................................10-15

ID Number ..........................................................................................................................................10-15

Source ID .............................................................................................................................................10-15

Swap ANI/DNIS ........................................................................................................................10-15

Quad T1/PRI Module (User Termination/RBS).................................................................................. 10-16

First DS0/Number of DS0s .......................................................................................................10-16

DS0s Available ............................................................................................................................10-16

Signaling Method .......................................................................................................................10-16

Direct Inward Dialing ................................................................................................................10-16

Caller ID Number ..............................................................................................................................10-17

Strip MSD .....................................................................................................................................10-17

Source ID ......................................................................................................................................10-17

Quad Nx56/64 Module (User Termination)......................................................................................... 10-17

Ports Available ............................................................................................................................10-18

Number of Ports .........................................................................................................................10-18

Number to dial ............................................................................................................................10-18

Call Type ......................................................................................................................................10-18

Table of Contents

xx ATLAS 800

PLUS

User Manual 61200226L1-1

Dial Call As ................................................................................................................................. 10-18

Source ID ..................................................................................................................................... 10-18

Min DS0s ..................................................................................................................................... 10-18

Max DS0s ..................................................................................................................................... 10-18

Octal BRI Module (Network Termination) .......................................................................................... 10-18

Switch Type ................................................................................................................................ 10-18

SPID List ...................................................................................................................................... 10-18

Strip MSD .................................................................................................................................... 10-19

Source ID ..................................................................................................................................... 10-19

Octal BRI Module (User Termination).................................................................................................. 10-20

Switch Type ................................................................................................................................ 10-20

SPID List ...................................................................................................................................... 10-20

Strip MSD .................................................................................................................................... 10-20

Source ID ..................................................................................................................................... 10-20

Outgoing Caller ID .................................................................................................................... 10-20

ID Presentation ........................................................................................................................... 10-21

ID Number .................................................................................................................................. 10-21

Creating Dial Plans—Examples............................................................................................................. 10-21

Understanding Dial Plan Configurations........................................................................................10-21

Chapter 11 Updating Firmware...............................................................................................................11-1

Overview..................................................................................................................................................... 11-1

XMODEM Firmware Updates.................................................................................................................. 11-1

Updating Firmware using XMODEM ...............................................................................................11-2

TFTP Firmware Updates........................................................................................................................... 11-4

Updating Firmware using TFTP.........................................................................................................11-4

Chapter 12 SNMP Management..............................................................................................................12-1

SNMP........................................................................................................................................................... 12-1

Basic Components.................................................................................................................................12-1

Network Manager........................................................................................................................ 12-1

Agent ............................................................................................................................................. 12-1

MIB................................................................................................................................................. 12-1

SNMP Traps................................................................................................................................................ 12-2

Trap Destination List............................................................................................................................12-2

Configuring a Trap Destination List via Terminal Menu...............................................................12-2

Filtering (Disabling) Traps...................................................................................................................12-2

Standard Traps............................................................................................................................. 12-3

DS1 Traps...................................................................................................................................... 12-3

DS1 Alarm Traps.......................................................................................................................... 12-3

DS1 Alert Traps............................................................................................................................ 12-4

Chapter 13 ADTRAN Utilities................................................................................................................13-1

Overview..................................................................................................................................................... 13-1

SysLog Host Daemon................................................................................................................................ 13-1

SysLog GUI............................................................................................................................................13-2

Monitor.......................................................................................................................................... 13-2

Menu Bar................................................................................................................................................13-3

File ................................................................................................................................................................ 13-3

Display......................................................................................................................................................... 13-3

Log Files....................................................................................................................................................... 13-4

Erase Log Files ..................................................................................................................................... 13-4

Define RED Events .............................................................................................................................. 13-4

Properties ............................................................................................................................................. 13-4

ADTRAN Atlas 800, ATLAS 800PLUS User manual

Related papers

Other documents