Avery Dennison 9493 Operating instructions

Category
Print & Scan
Type
Operating instructions

This manual is also suitable for

Avery Dennison 9493 SNP is a versatile mobile printer that empowers you to create professional-looking labels on the go. With its compact size and lightweight design, you can easily take it with you wherever you need to print. Whether you're in the office, at home, or on the road, this printer offers the convenience and portability you need to get the job done.

Avery Dennison 9493 SNP is a versatile mobile printer that empowers you to create professional-looking labels on the go. With its compact size and lightweight design, you can easily take it with you wherever you need to print. Whether you're in the office, at home, or on the road, this printer offers the convenience and portability you need to get the job done.

Monarch®, 9493, and 9496 are trademarks of Paxar Americas, Inc. ©2008 Avery Dennison Corp.
TC9496OI Rev. AA 10/08 All rights reserved.
OPERATING
INSTRUCTIONS
The Monarch® 9496™ Battery Charger/AC Adapter
charges the 14.8V lithium-Ion battery in your Monarch
9493™ printer and provides AC power to the printer.
You must charge a battery before using it for the first
time.
WARNINGS
Use only the 9496 charger/adapter designed for
Lithium-Ion batteries when charging. The battery
may explode if plugged into a different charger.
Do not charge any other batteries with this
charger.
Do not throw the battery in the trash. Recycle
according to your local regulations.
Do not disassemble, short-circuit, heat above
122°F (50°C), or incinerate the battery. It may
explode.
Follow the operating and storage limit
specifications listed at the end of these
instructions. Otherwise, the battery may
permanently lose its charge capacity.
Unplug the charger and remove the battery from
the printer if storing for a week or more.
Providing AC Power
The battery must be installed in the printer to use the
AC power adapter. The AC adapter maintains the
battery’s current charge capacity while the printer is in
use. Turn off the printer to fully charge the battery.
2
Charging the Battery
You can charge the battery either in or outside of the
printer.
1. Connect an AC power cord into the charger.
2. Plug the power cord into a grounded electrical
outlet.
3. Plug the charger into the socket on the right side
of the battery.
The LED lights up as the battery charges. It may take
2-3 hours for the battery to fully charge.
Reading the LED
The green charger LED indicates the following
activity:
LED Charge Status
1 Blink Pre-charge
2 Blinks Charging
3 Blinks
Battery usable (at 80%
capacity)
Continuous blinking Error
Solid Charge complete
Battery
Socket
Charger
LED
3
Troubleshooting
When an error occurs, the charger LED blinks
continuously. In this case, repeat the charging
process.
If the error still occurs, repeat the process with a new
battery. If there is a still a problem call Service.
Specifications
Operating
Limits:
32°F to 104°F (0°C to 40°C)
Storage Limits:
-4°F to 122°F (-20°C to 50°C)
Humidity:
5% to 90% non-condensing
Charger
Length:
4.8” (120 mm)
Width:
2.14” (53.4 mm)
Height:
1.5” (38 mm)
Input:
90 to 264 VDC 50/60 Hz
Output:
16.5 VDC/1.4A
Visit www.monarch.com for sales, service, supplies,
information, and telephone numbers for our locations
throughout the world.
Toll Free:
1-800-543-6650 (In the U.S.A.)
1-800-363-7525 (In Canada)
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Avery Dennison 9493 Operating instructions

Category
Print & Scan
Type
Operating instructions
This manual is also suitable for

Avery Dennison 9493 SNP is a versatile mobile printer that empowers you to create professional-looking labels on the go. With its compact size and lightweight design, you can easily take it with you wherever you need to print. Whether you're in the office, at home, or on the road, this printer offers the convenience and portability you need to get the job done.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI