Classen SC-12/8.0 User manual

Brand: Classen

Model: SC-12/8.0

Category: Security cameras

Type: User manual

Schiller-Pfeiffer, Inc.

1028 Street Road • Southampton, PA 18966

Telephone: 1-800-366-6268 • Teléfono: + (877) 596 6337

SOD CUTTER

OPERATOR’S/PARTS MANUAL

SC-12/5.5 - S.N. 000405 & UP; SC-12/8.0 - S.N. 000139 & UP

SC-16/5.5 - S.N. 000105 & UP; SC-18/5.5 - S.N. 004713 & UP

SC-18/8.0 - S.N. 000503 & UP; SC-20/5.5 - S.N. 000152 & UP

SC-20/8.0 - S.N. 000182 & UP; SC-24/8.0 - S.N. 000178 & UP

Model SC-18 shown

Modelo SC-18 ilustrado

CORTADOR DE TEPE MANUAL

DEL OPERADOR/PIEZAS

SC-12/5.5 - S.N. 000405 Y SIG; SC-12/8.0 - S.N. 000139 Y SIG

SC-16/5.5 - S.N. 000105 Y SIG; SC-18/5.5 - S.N. 004713 Y SIG

SC-18/8.0 - S.N. 000503 Y SIG; SC-20/5.5 - S.N. 000152 Y SIG

SC-20/8.0 - S.N. 000182 Y SIG; SC-24/8.0 - S.N. 000178 Y SIG

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Thank You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Read This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Directions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

OWNER’S RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

PRE-DELIVERY CHECK LIST. . . . . . . . . . . . . . . . . . . . . . . 1

DELIVERY CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Handle Fuel Safely - Avoid Fires . . . . . . . . . . . . . . . . . . . 2

Read Safety Signs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operate Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Protect Children . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Avoid Tipping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operate Safely On Slopes . . . . . . . . . . . . . . . . . . . . . . . . 2

Practice Safe Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 2

Start Engine Safely. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ENGINE STARTING PROCEDURES . . . . . . . . . . . . . . . . . . 2

Engine Oil Level Check . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Transmission Oil Level Check . . . . . . . . . . . . . . . . . . . . . 2

Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Stopping Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

OPERATING THE SOD CUTTER. . . . . . . . . . . . . . . . . . . . . 3

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BLADE ANGLE (PITCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . 3

TROUBLESHOOTING CHART . . . . . . . . . . . . . . . . . . . . . . 4

SOD CUTTER PARTS MANUAL . . . . . . . . . . . . . . . . . . . . . 5

Main Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Power Train Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Handle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TWO YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . 10

ÍNDICE

INTRODUCCIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Gracias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Lea este manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Mediciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Números de serie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Instrucciones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

REGISTRO DEL PROPIETARIO . . . . . . . . . . . . . . . . . . . . 11

LISTA DE COMPROBACIÓN ANTERIOR A LA ENTREGA

. . 11

LISTA DE COMPROBACIÓN DE ENTREGA. . . . . . . . . . 11

SEGURIDAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Manipule el combustible con cuidado – Evite los

incendios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Lea los letreros de seguridad . . . . . . . . . . . . . . . . . . . . . 12

Haga funcionar de forma segura . . . . . . . . . . . . . . . . . . 12

Proteja a los niños . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Evite los vuelcos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Haga funcionar de forma segura en pendientes . . . . . . 12

Practique un mantenimiento seguro . . . . . . . . . . . . . . . . 12

Arranque el motor de forma segura . . . . . . . . . . . . . . . . 12

PROCEDIMIENTOS DE ARRANQUE DEL MOTOR. . . . 12

Compruebe el nivel de aceite del motor. . . . . . . . . . . . . 12

Compruebe el nivel de aceite de la transmisión. . . . . . . 12

Arranque del motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Parada del motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CÓMO HACER FUNCIONAR EL CORTADOR DE TEPE. . 13

Preparación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ÁNGULO DE LA HOJA (INCLINACIÓN). . . . . . . . . . . . . 13

MANTENIMIENTO GENERAL . . . . . . . . . . . . . . . . . . . . . 13

TABLA DE LOCALIZACIÓN Y RESOLUCIÓN DE

PROBLEMAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MANUAL DE PIEZAS DEL CORTADOR DE TEPE . . . . 15

Bastidor principal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Conjunto del sistema de transmisión . . . . . . . . . . . . . . . 17

Conjunto de manillar . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

GARANTÍA LIMITADA DE DOS AÑOS. . . . . . . . . . . . . . 20

PRE-DELIVERY CHECK LIST

Check the following before you deliver the sod cutter to the

customer.

1. Guards and shields fastened in place.

2. Decals fastened and legible.

3. Tire pressure.

4. Gas lever on engine turned on.

5. All eight lubrication points greased.

6. 2:1 gearbox oil level.

7. Engine oil level.

8. Air cleaner.

9. Touch up scratches.

10. Chain tight.

11. Engine belt tight.

12. Levers working properly.

13. All controls.

14. Add fuel, start engine, test run.

DATE SET UP __________/__________/__________

DELIVERY CHECK LIST

Review the operators manual with the customer.

Explain the following:

1. Classen Mfg., Inc. warranty.

2. Safe operation and service.

3. How to use controls.

4. Operating the machine correctly.

5. Transporting the sod cutter.

6. Correct fuel and lubricants.

7. Daily and periodic inspections.

8. Changing oil after break-in period.

9. Servicing the sod cutter regularly and correctly.

10. Classen Mfg., Inc. parts and service.

11. Give the customer the operators manual and

encourage customer to read it.

DATE DELIVERED __________/__________/__________

SIGNATURE _______________________________________

INTRODUCTION

THANK YOU

Thank you for purchasing the Classen Model SC-20, SC-18, or

SC-12 sod cutter.

READ THIS MANUAL

Read this manual carefully to learn how to operate sod cutter

correctly. Failure to do so could result in personal injury or

equipment damage.

This manual should be considered a permanent part of your

sod cutter and should remain with it if you sell it.

WARRANTY

Refer to back page.

MEASUREMENTS

U.S. units of measure are used in this manual.

SERIAL NUMBERS

Write frame and engine serial numbers, plus model numbers in

"Owners Record" section below. Your dealer needs these

numbers when you order parts. The serial number is located on

a sticker on the center section of the frame.

DIRECTIONS

"Right Hand" and "Left Hand" sides of the sod cutter are

determined by facing the back of the sod cutter as you would

operate the machine.

OWNER’S RECORD

DATE PURCHASED _________________________________

SOD CUTTER MODEL NUMBER______________________

SOD CUTTER SERIAL NUMBER______________________

ENGINE MODEL NUMBER __________________________

ENGINE SERIAL NUMBER___________________________

SAFETY

HANDLE FUEL SAFELY - AVOID FIRES

Handle gasoline with care; it is highly flammable. Use an

approved gasoline container.

Fill the fuel tank outdoors.

DO NO

T fill tank completely full.

DO NOT smoke while you fill fuel tank.

DO NOT remove gas cap if engine is running.

READ SAFETY SIGNS

Carefully read and follow all caution stickers.

WARNING

ALL GUARDS MUST BE IN PLACE

WHILE MACHINE IS IN OPERATION

OPERATE SAFELY

Carefully read this manual and operate sod cutter correctly.

PROTECT CHILDREN

Keep children and pets out of the area where you are cutting

sod.

AVOID TIPPING

Make sure you do not get too close to sharp drop-offs to avoid

tipping sod cutter over.

OPERATE SAFELY ON SLOPES

You may cut sod any direction on slopes, however, make sure

you do this carefully. Cutting on slopes can be dangerous. To

avoid any accidents, make sure to leave yourself room to

correct the problem if one arises. Always park your sod cutter

on level ground.

PRACTICE SAFE MAINTENANCE

Keep all machine parts in good condition and fastened in

place. Fix damages immediately. Replace worn or broken

parts. Whenever you work on the sod cutter, disconnect spark

plug wire.

START ENGINE SAFELY

Make sure hands and feet are out of the way of moving parts

when starting engine.

WARNING

KEEP HANDS & FEET AWAY

FROM MOVING PARTS

ENGINE STARTING

PROCEDURES

NOTICE: There are two locations on this engine that require

oil, both the crankcase and the transmission

(gearbox). Running the engine or gearbox with a low

oil level can cause engine damage. Refer to the

engine manual for complete engine information

and recommendations.

ENGINE OIL LEVEL CHECK

1. BEFORE CHECKING ENGINE:

• make certain the engine is level

• the engine switch is in the OFF position

• the sod cutter blade is NOT engaged

• the drive wheels are disengaged.

2. Remove the filler cap/dipstick and wipe it clean.

3. Insert and remove the dipstick without screwing it

into the filler neck. Check the oil level shown on the

dipstick.

4. If the oil level is low, fill to the edge of the oil filler

hole with the recommended oil. SAE 10W-30 is

recommended for general use. Refer to engine oil

recommendations in engine manual for other

viscosities and information.

5. Screw in the filler cap/dipstick securely.

TRANSMISSION OIL LEVEL CHECK

1. Check the transmission oil level with the engine

stopped and in a level position.

2. Remove the filler cap/dipstick and wipe it clean.

3. Insert and remove the dipstick without screwing it

into the filler hole. Check the oil level shown on the

dipstick.

4. If the oil level is low, add oil to reach the upper limit

mark on the dipstick. Use the same oil that is

recommended for the engine, SAE 10W-30.

5. Screw in the filler cap/dipstick securely.

ARTING ENGINE

1. Turn fuel cock to the "open" position.

2. Turn choke on (closed).

3. Turn ignition switch to "on".

4. Move throttle lever on engine to half throttle position.

5. Pull recoil starter rope until engine starts.

6. After engine is warm, turn off choke (open).

7. Allow engine to run one minute before cutting sod.

8. Check engine rpm setting before operating. DO NOT

exceed 3600 rpm.

STOPPING ENGINE

1. Turn throttle to "slow" position.

2. Turn off ignition switch.

OPERATING THE

SOD CUTTER

PREPARATION

1. Police lawn area for obstacles and debris (i.e.

sprinklers, hoses, toys, etc.). Remove all items.

2. Make sure underground sprinkler heads and other

hidden obstacles are marked to prevent damage.

3. Mark other areas where sod cutting will be a problem

or too risky (i.e. mud, tree roots, steep hills).

OPERATING

1. Start the engine. CAUTION: To avoid injury, do not

place your feet or other body parts under the blade

while starting the engine.

2. Select the correct cutting depth desired up to 2 1/2

inches. Loosen the tee handle from the depth gauge

plate, located under the height adjustment bar, (#3 on

illustration) and put it to the correct height setting.

Tighten the tee handle.

3. Push the wheel drive handle (#5 on illustration) and

the cutter blade handle (#4 on illustration) to the "on"

position toward the engine.

4. Raise the main handle upward so the front nose of the

sod cutter rests on the ground.

5. Loosen the 1/2" handle nut (#2 on illustration) and

lower the height adjustment bar to rest on the depth

gauge. Now tighten the 1/2" handle nut securely so it

will not loosen with the vibration of the machine.

6. Go to the back of the machine and lower the handle

until the cutting blade rests on the ground. You are

now ready to cut sod.

7. Turn the throttle to the desired operating speed by

twisting the throttle control (#6 on illustration) toward

you. Maximum engine rpm is recommended for

smooth operation.

8. After cutting a short distance, stop machine by letting

the twist grip throttle control go back to its original

position. Check thickness of cut and adjust if necessary.

9. At the end of each cutting pass, lift up on the handle

bar to clear the cutting blade from the sod. Retard the

throttle control and turn machine around into the

position for the next cut.

10. When finished cutting sod, reverse steps 6 through 3,

leaving the wheel drive handle on for transportation.

BLADE ANGLE (PITCH)

Under normal operating conditions, the blade angle is slight

(blade bottom is flat). In extremely hard soil or when cutting

with a dull blade, the blade may want to ride out of the ground.

At this time, it may help to angle the blade down. A short trial

run will indicate what blade angle is best. To do this, you will

loosen the pitch adjustment bolt (#7 on illustration) and move

it slightly toward the engine, then retighten bolt and nut.

GENERAL MAINTENANCE

To keep the sod cutter in good operating condition, perform

the following:

• Keep blade sharp; a sharp blade cuts cleaner, faster and

more uniformly and places less load on the machine.

Sharpen cutting edge on bevel or top side only.

• Keep drive belt at proper tension and free of oil and

dirt at all times.

• Check engine oil level and air filter element daily.

• Check for loose bolts and connections.

• All grease fittings are pressurized type. Use a good

grade Lithium Base Grease or equivalent. Grease

eccentric arms sparingly every 4 hours of service, all

others daily. Wipe off all grease fittings before and after

each greasing (there are a total of 8 grease fittings).

• To make sure the chain on the front drive wheels is

tight, you will need to remove the chain guard to

check this. If tightening is required, loosen nuts and

bolts on the 3/4" pillow block bearings and push the

bearings toward the back of the sod cutter until chain

is tight. Make sure both bearings go back evenly to

keep jackshaft running even with the frame. After

doing this, retighten nuts and bolts on the bearing and

replace the chain guard.

• Engine (refer to Honda owner’s manual).

SAFETY WARNING

DO NOT STORE GASOLINE (FUEL)

UNNECESSARILY OVER LONG PERIODS OF

TIME. TO PREVENT POSSIBLE EXPLOSION,

STORE ONLY IN AN APPROVED "SAFE"

CONTAINER. TO PREVENT EXPLOSION OF

VAPORIZED FUEL, DO NOT STORE MACHINE

WITH FUEL IN TANK OR CARBURETOR IN AN

ENCLOSURE WITH OPEN FLAME.

(EXAMPLE: FURNACE OR WATER HEATER

PILOT LIGHT.)

TROUBLESHOOTING

CHART

PROBLEM CAUSE REMEDY

Blade will not stay in ground a. Bottom of blade is rounded

off

a. Blade should be sharpened

or replaced

Belts jump off a. Wrong type of belt

b. Pulley misalignment

a. Use only the special factory

belt

b. Realign pulley

NOTES:____________________________________________________________________________________________________

___________________________________________________________________________________________________________

Page is loading ...

SOD CUTTER MAIN FRAME

1 C400235 1 SOD CUTTER FRAME

2 C500131 2 1/2" LOCK NUT

3 C500150 2 1/2" x 1-1/2" BOLT

4 C400232 1 SMALL GUARD

5 C400114 1 DUAL DRIVE CLUTCH ARM

6 C500101 4 5/16" NUT

7 C500115 9 5/16" LOCK WASHER

8 C500140 6 5/16" x 3/4" BOLT

9 C500146 2 3/8" x 1-1/2" BOLT

10 C500083 6 5/16" FLAT WASHER

11 C300069 1 DRIVE LINKAGE ARM

12 C100208 1 DUAL DRIVE DOUBLE IDLER PULLEY

13 C500106 1 1/2" NUT

14 C500006 1 1/2" LOCK WASHER

15 C300002 1 AXLE PIN

16 C100017 1 TIRE & WHEEL ASSEMBLY, 9x350x4

17 C500016 2 5/32" x 1-1/2" COTTER PIN

18 C400233 1 CHAIN GUARD

19 C500219 2 5/16" x 5" BOLT

20 C500041 2 3/8" LOCK NUT

21 C400234 1 LARGE GUARD

22 C500130 6 3/8" LOCK WASHER

23 C500129 8 3/8" NUT

24 C100010 2 IDLER PULLEY

25 C500042 14 3/8" FLAT WASHER

26 C500091 2 3/8" x 2" BOLT

27 C100021 2 BRASS BUSHING

28 C500001 1 GREASE FITTING, 1/4" x 28

29 C400010 1 CLUTCH ARM

30 C300134 1 L.H. BELT ADJUSTMENT CLIP

31 C500043 2 3/8" x 1" BOLT

32 C500159 1 3/8" x 3" BOLT

33 C100074 2 DECAL, "CLASSEN"

34 C100262 2 DECAL, "SC-12"

34 C100417 2 DECAL, "SC-16"

34 C100131 2 DECAL, "SC-18"

34 C100260 2 DECAL, "SC-20"

34 C100345 2 DECAL, "SC-24"

35 C100069 1 DECAL, "DANGER"

36 C100096 1 DECAL, "ALL GUARDS"

37 C100132 1 DECAL, "CUTTER BLADE"

38 C100133 1 DECAL, "SLOW/FAST"

39 C100134 1 DECAL, "WHEEL DRIVE"

40 C100106 1 DECAL, SERIAL NUMBER

41 C100073 1 LUBRICATION TAG

42 C300004 1 R.H. BELT ADJUSTMENT CLIP

43 C500154 1 3/8" x 2-1/2" BOLT

44 C400237 1 BUMPER

45 C400011 2 12" BLADE ADAPTOR

46 C500133 12 5/16" x 1" BOLT

47 C300133 2 16" BLADE ADAPTOR

48 C500142 6 5/16" x 2" BOLT

49 C300047 2 20" BLADE ADAPTOR

50 C400188 2 24" BLADE ADAPTOR

QTY/PER

KEY PART NO. SHEET DESCRIPTION

QTY/PER

KEY PART NO. SHEET DESCRIPTION

1 C100005 1 HONDA 5.5 hp ENGINE w/DEFLECTOR

1 C100114 1 HONDA 8.0hp ENGINE w/DEFLECTOR

2 C100028 1 PULLEY w/ HUB & BOLTS, 4" x 22mm

3 C100024 1 B56 V-BELT, 5.5hp MODEL

3 C100113 1 B59 V-BELT, 8.0hp MODEL

4 C500011 1 3/16" x 1 3/4" SQUARE KEY

5 C500029 2 1/4" x 3/4" BOLT

6 C100023 1 HUB, TAPERLOCK

7 C100022 1 PULLEY, TAPERLOCK

8 C100008 1 REDUCTION BOX, and KEYS

9 C500174 8 1/2" x 1 3/4" BOLTS

10 C500042 8 3/8" FLAT WASHER

11 C200031 1 PULLEY, DUAL DRIVE 5" SPLIT, and KEY

12 C500004 1 1/4" x 1" SQUARE KEY

13 C500130 10 3/8" LOCK WASHER

14 C500129 12 3/8" NUT

15 C100026 1 6934 V-BELT

16 C100011 2 BX31 DRIVE V-BELT (ONLY 1 BELT ON SC-12)

17 C500003 4 1/4" x 7/8" HALF MOON KEY

18 C700002 2 ECCENTRIC HUB

19 C100004 4 1" PILLOW BLOCK w/COLLAR

20 C600003 1 ECCENTRIC SHAFT

21 C500034 8 1/2" FLAT WASHER

22 C500006 16 1/2" LOCK WASHER

23 C500106 16 1/2" NUT

24 C200002 1 6" PULLEY w/ 1" HUB

SOD CUTTER POWER TRAIN ASSEMBLY

QTY/PER

KEY PART NO. SHEET DESCRIPTION

QTY/PER

KEY PART NO. SHEET DESCRIPTION

25 C500181 1 1/4" x 1-1/2" SQUARE KEY

26 C100207 1 SHEAVE, DUAL DRIVE DOUBLE V-BELT

26 C100014 1 SHEAVE, SINGLE DRIVE (MODEL SC-12)

27 C500147 8 5/16" x 1-1/2" BOLT

28 C100013 2 3/4" PILLOW BLOCK w/ COLLAR

29 C500083 8 5/16" FLAT WASHER

30 C500115 8 5/16" LOCK WASHER

31 C500101 8 5/16" NUT

32 C200039 1 JACKSHAFT, w/SPROCKET & HUB

33 C100307 1 #40 CHAIN

34 C100025 1 CONNECTING LINK

35 C500158 8 1/2" x 3-1/2" BOLT

36 C700024 4 DRIVE WHEEL (2 WHEELS ON SC-12)

37 C300001 1 DRIVE SHAFT SPACER

38 C600004 1 DRIVE SHAFT

39 C500154 1 3/8" x 2-1/2" BOLT

40 C300004 1 R.H. BELT ADJUSTMENT CLIP

41 C500136 4 1/4" NUT

42 C500137 4 1/2" LOCK WASHER

43 C100027 1 THROTTLE SPRING

44 C500157 2 1/4" x 3-1/2" BOLT

45 C500146 4 3/8" x 1-1/2" BOLT

46 C200001 1 DRIVE SHAFT SPROCKET

47 C500159 1 3/8" x 3" BOLT

48 C500043 2 3/8" x 1" BOLT

49 C300134 1 L.H. BELT ADJUSTMENT CLIP

SOD CUTTER HANDLE ASSEMBLY

QTY/PER

KEY PART NO. SHEET DESCRIPTION

1 C100018 1 L.H. HANDLE GRIP

2 C400243 1 MAIN HANDLE

3 C300138 1 HANDLE BRACE

4 C500043 6 3/8" x 1" BOLT

5 C100486 1 THUMB THROTTLE & CABLE

6 C500041 9 3/8" LOCK NUT

7 C500118 2 1/4" x 1 3/4" BOLT

8 C500136 2 1/4" NUT

9 C500137 3 1/4" LOCK WASHER

10 C100007 4 RUBBER GRIP

11 C400008 2 HANDLE ENGAGEMENT

12 C500019 2 SMALL HANDLE SPRING

13 C500139 2 1/4" LOCK NUT

14 C100029 1 12" CUTTING BLADE

14 C100416 1 16" CUTTING BLADE

14 C100016 1 18" CUTTING BLADE

14 C100110 1 20" CUTTING BLADE

14 C100329 1 24" CUTTING BLADE

15 C500154 2 3/8" x 2 1/2" BOLT

16 C500042 2 3/8" FLAT WASHER

17 C400074 1 WHEEL DRIVE ADJUSTMENT ARM

18 C500025 2 3/8" FINE NUT

19 C500026 2 3/8" CLEVIS YOKE

20 C500134 2 3/8" x 1-1/4" BOLT

21 C500146 2 3/8" x 1-1/2" BOLT

22 C500133 8 5/16" x 1" BOLT

23 C500101 12 5/16" NUT

24 C500115 10 5/16" LOCK WASHER

25 C500074 2 5/16" x 1-3/4" BOLT

26 C500001 7 GREASE FITTING, 1/4" x 28

27 C400110 1 PIVOT ASSEMBLY

28 C500130 6 3/8" LOCK WASHER

29 C500129 6 3/8" NUT

30 C400007 1 CUTTING BLADE ADJUSTMENT ARM

31 C500007 1 1/2" HANDLE NUT

32 C500006 6 1/2" LOCK WASHER

33 C500034 10 1/2" FLAT WASHER

34 C400001 1 HEIGHT ADJUSTMENT BAR

35 C400238 1 PITCH ADJUSTMENT BAR

36 C300039 1 DEPTH GAUGE

37 C400239 1 1/4" THREADED T HANDLE

38 C200005 1 HEIGHT ADJUSTMENT BOLT

39 C200004 1 PITCH ADJUSTMENT BOLT

40 C500106 4 1/2" NUT

41 C500152 2 1/2" x 2-3/4" BOLT

42 C500151 2 1/2" x 3" FINE BOLT

43 C100001 12 3/4" NYLON WASHER

44 C100002 12 SEAL

45 C600001 6 STEEL SLEEVE

46 C800001 2 ECCENTRIC ARM

47 C100003 6 BEARING

48 C800002 2 BLADE ARM

49 C500088 1 1/4" FLAT WASHER

QTY/PER

KEY PART NO. SHEET DESCRIPTION

Page is loading ...

TWO YEAR LIMITED WARRANTY

Effective April 1, 2007

For the period of two years from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser free

of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk,

Nebraska, to be defective in material or workmanship. All transportation charges on parts submitted for repair or replacement under

this warranty shall be borne by the purchaser.

This warranty does not include engines or engine parts, tires, batteries, or gearboxes that are covered under separate warranties

furnished by their manufacturer or supplier, nor does it include normal maintenance parts, including but not limited to, spark plugs,

points, filters, blades, and lubricants.

All service under this warranty will be furnished or performed by our factory authorized service stations.

There is no other expressed warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are

limited to two years from the date of purchase and to the extent permitted by law, any and all implied warranties are excluded. The

above remedy of repair and replacement of defective parts is the purchaser’s exclusive remedy for any defect, malfunction or breach

of warranty. Liability for incidental or consequential damages under any and all warranties is excluded to the extent permitted

by law.

NORMAL RESPONSIBILITIES OF THE SELLER AND THE USER

1. The Distributor or Dealer is responsible for the proper assembly and preparation of the product for delivery to the end user.

2. The User is responsible for reading the Manual and Instructions.

3. The User is responsible for proper operation and maintenance as described in the manual.

4. The User is responsible for the replacement of wear items such as blades, belts, tires, batteries, etc.

5. The User is responsible for damage due to improper operation and maintenance, as well as abuse.

All claims must be received by the factory 30 days after the end of the warranty period to receive warranty consideration.

Schiller-Pfeiffer, Inc.

1028 Street Road • Southampton, PA 18966

Telephone: 1-800-366-6268

Page is loading ...

CORTADOR DE TEPE

MANUAL DE PIEZAS

SC-12/5.5 – N/S 000405 y sig.

SC-12/8.0 – N/S 000139 y sig.

SC-16/5.5 – N/S 000105 y sig.

SC-18/5.5 – N/S 004713 y sig.

SC-18/8.0 – N/S 000503 y sig.

SC-20/5.5 – N/S 000152 y sig.

SC-20/8.0 – N/S 000182 y sig.

SC-24/8.0 – N/S 000178 y sig.

BASTIDOR PRINCIPAL EL CORTADOR DE TEPE

1 C400235 1 BASTIDOR DEL CORTADOR DE TEPE

2 C500131 2 TUERCA DE TRABA DE 1/2”

3 C500150 2 PERNO DE 1/2” x 1 1/2”

4 C400232 1 PROTECTOR PEQUEÑO

5 C400114 1

BRAZO DEL EMBRAGUE DE IMPULSIÓN DOBLE

6 C500101 4 TUERCA DE 5/16”

7 C500115 9 ARANDELA DE TRABA DE 5/16”

8 C500140 6 PERNO DE 5/16” x 3/4”

9 C500146 2 PERNO DE 3/8” x 1 1/2”

10 C500083 6 ARANDELA PLANA DE 5/16”

11 C300069 1 BRAZO DE ARTICULACIÓN DE IMPULSIÓN

12 C100208 1 POLEA LOCA DOBLE DE IMPULSIÓN DOBLE

13 C500106 1 TUERCA DE 1/2”

14 C500006 1 ARANDELA DE TRABA DE 1/2”

15 C300002 1 PASADOR DE EJE

16 C100017 1

CONJUNTO DE NEUMÁTICO Y RUEDA DE 9 x 350 x 4

17 C500016 2 PASADOR DE ALETA DE 5/32” x 1 1/2”

18 C400233 1 PROTECTOR DE CADENA

19 C500219 2 PERNO DE 5/16” x 5”

20 C500041 2 TUERCA DE TRABA DE 3/8”

21 C400234 1 PROTECTOR GRANDE

22 C500130 6 ARANDELA DE TRABA DE 3/8”

23 C500129 8 TUERCA DE 3/8”

24 C100010 2 POLEA LOCA

25 C500042 14 ARANDELA PLANA DE 3/8”

26 C500091 2 PERNO DE 3/8” x 2”

27 C100021 2 MANGUITO DE LATÓN

28 C500001 1 GRASERA DE 1/4” x 28

29 C400010 1 BRAZO DEL EMBRAGUE

30 C300134 1

PRESILLA DE AJUSTE DE LA CORREA IZQUIERDA

31 C500043 2 PERNO DE 3/8” x 1”

32 C500159 1 PERNO DE 3/8” x 3”

33 C100074 2 CALCOMANÍA “CLASSEN”

34 C100262 2 CALCOMANÍA “SC-12”

34 C100417 2 CALCOMANÍA “SC-16”

34 C100131 2 CALCOMANÍA “SC-18”

34 C100260 2 CALCOMANÍA “SC-20”

34 C100345 2 CALCOMANÍA “SC-24”

35 C100069 1 CALCOMANÍA DE “PELIGRO”

36 C100096 1

CALCOMANÍA DE “TODOS LOS PROTECTORES”

37 C100132 1 CALCOMANÍA “HOJA DE CORTADOR”

38 C100133 1 CALCOMANÍA “LENTO/RÁPIDO”

39 C100134 1 CALCOMANÍA “RUEDA DE IMPULSIÓN”

40 C100106 1 CALCOMANÍA DE “NÚMERO DE SERIE”

41 C100073 1 ETIQUETA DE LUBRICACIÓN

42 C300004 1

PRESILLA DE AJUSTE DE LA CORREA DERECHA

43 C500154 1 PERNO DE 3/8” x 2 1/2”

44 C400237 1 TOPE

45 C400011 2 ADAPTADOR DE HOJA DE 12”

46 C500133 12 PERNO DE 5/16” x 1”

47 C300133 2 ADAPTADOR DE HOJA DE 16”

48 C500142 6 PERNO DE 5/16” x 2”

49 C300047 2 ADAPTADOR DE HOJA DE 20”

50 C400188 2 ADAPTADOR DE HOJA DE 24”

CADA./POR

CLAVE N° DE PIEZA.

HOJA DESCRIPCIÓN

CADA./POR

CLAVE N° DE PIEZA.

HOJA DESCRIPCIÓN

1 C100005 1 MOTOR HONDA DE 5,5 HP CON DEFLECTOR

1 C100114 1 MOTOR HONDA DE 8,0 HP CON DEFLECTOR

2 C100028 1 POLEA CON CUBO Y PERNOS DE 4” x 22 mm

3 C100024 1 CORREA TRAPECIAL B56 MODELO DE 5,5 HP

3 C100113 1 CORREA TRAPECIAL B59 MODELO DE 8,0 HP

4 C500011 1 CHAVETA CUADRADA DE 3/16” x 1 3/4”

5 C500029 2 PERNO DE 1/4” x 3/4”

6 C100023 1 CUBO TAPERLOCK

7 C100022 1 POLEA TAPERLOCK

8 C100008 1 CAJA DE REDUCCIÓN Y CHAVETAS

9 C500174 8 PERNOS DE 1/2” x 1 3/4”

10 C500042 8 ARANDELA PLANA DE 3/8”

11 C200031 1

POLEA DE IMPULSIÓN DOBLE DE 5” DIVIDIDA Y CHAVETA

12 C500004 1 CHAVETA CUADRADA DE 1/4” X 1”

13 C500130 10 ARANDELA DE TRABA DE 3/8”

14 C500129 12 TUERCA DE 3/8”

15 C100026 1 CORREA TRAPECIAL 6934

16 C100011 2

CORREA TRAPECIAL BX31 (SOLAMENTE 1 CORREA EN SC-12)

17 C500003 4 CHAVETA DE MEDIA LUNA DE 1/4” x 7/8”

18 C700002 2 CUBO EXCÉNTRICO

19 C100004 4 CHUMACERA DE 1” CON COLLAR

20 C600003 1 EJE EXCÉNTRICO

21 C500034 8 ARANDELA PLANA DE 1/2”

22 C500006 16 ARANDELA DE TRABA DE 1/2”

23 C500106 16 TUERCA DE 1/2”

24 C200002 1 POLEA DE 6” CON CUBO DE 1”

CONJUNTO DEL TREN DE FUERZA DEL CORTADOR DE TEPE

CADA./POR

CLAVE N° DE PIEZA.

HOJA DESCRIPCIÓN

CADA./POR

CLAVE N° DE PIEZA.

HOJA DESCRIPCIÓN

25 C500181 1 CHAVETA CUADRADA DE 1/4” x 1 1/2”

26 C100207 1

ROLDANA DE CORREA TRAPECIAL DOBLE DE IMPULSIÓN DE DOBLE

26 C100014 1

ROLDANA DE IMPULSIÓN INDIVIDUAL (MODELO SC-12)

27 C500147 8 PERNO DE 5/16” x 1 1/2”

28 C100013 2 CHUMACERA DE 3/4” CON COLLAR

29 C500083 8 ARANDELA PLANA DE 5/16”

30 C500115 8 ARANDELA DE TRABA DE 5/16”

31 C500101 8 TUERCA DE 5/16”

32 C200039 1

EJE INTERMEDIO CON RUEDA DENTADA Y CUBO

33 C100307 1 CADENA N° 40

34 C100025 1 ESLABÓN

35 C500158 8 PERNO DE 1/2” x 3 1/2”

36 C700024 4 RUEDA DE IMPULSIÓN (2 RUEDAS EN SC-12)

37 C300001 1 ESPACIADOR DEL EJE DE IMPULSIÓN

38 C600004 1 EJE DE IMPULSIÓN

39 C500154 1 PERNO DE 3/8” x 2 1/2”

40 C300004 1

PRESILLA DE AJUSTE DE LA CORREA DERECHA

41 C500136 4 TUERCA DE 1/4”

42 C500137 4 ARANDELA DE TRABA DE 1/2”

43 C100027 1 RESORTE DEL ACELERADOR

44 C500157 2 PERNO DE 1/4” x 3 1/2”

45 C500146 4 PERNO DE 3/8” x 1 1/2”

46 C200001 1 RUEDA DENTADA DEL EJE DE IMPULSIÓN

47 C500159 1 PERNO DE 3/8” x 3”

48 C500043 2 PERNO DE 3/8” x 1”

49 C300134 1

PRESILLA DE AJUSTE DE LA CORREA IZQUIERDA

Page is loading ...

Classen SC-12/8.0 User manual

Brand: Classen

Model: SC-12/8.0

Category: Security cameras

Type: User manual

Download PDF

report

in other languages

español: Classen SC-12/8.0 Manual de usuario

Classen SC-12/8.0 User manual

Classen SC-12/8.0 User manual

in other languages

Related papers

Other documents