Intellinet 524810 User manual

Brand: Intellinet

Model: 524810

Category: Networking

Type: User manual

This manual is also suitable for

Wireless 150N PCI Card

WIRELESS

150N PCI

CARD

USER

MANUAL

MODEL 524810

INT-524810-UM-0110-04

section page

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

Wireless

150N PCI Card, Model 524810.

This compact high-speed adapter allows you to connect your desktop computer to

wireless networks so you can transfer or receive digital images, videos and MP3

les faster than ever, connecting to the wireless network with link speeds of up to

150 Mbps using the latest in wireless technology. This adapter is also compatible

with 802.11b and 802.11g wireless access points and wireless routers, giving you

the exibility to start upgrading your wireless network without the need to replace

your existing equipment.

Detailed instructions in this user manual make installation reasonably quick and

simple so you’ll soon be enjoying the benets of all these additonal features:

• Detachable 3 dBi antenna with reverse SMA connector

• Supports WMM (Wi-Fi Multimedia) for increased multimedia data throughput

• Supports the most popular operating systems: Windows 2000, XP, Vista and 7

• Supports Software AP function (turns your wireless client into a wireless access

point)

• Includes low prole 8 cm bracket

• Three-Year Warranty

System Requirements

• Desktop PC with Pentium 300 MHz-compatible processor or higher

• Windows 2000, XP, 2003, Vista or 7

• Available 32-bit PCI slot

Package Contents

• Wireless 150N PCI Card

• 1 antenna

• Quick install guide

• Low prole 8 cm bracket

• Setup CD with user manual

NOTE: Some screen images have been modied to t the format of this manual.

SAFETY & COMPLIANCE STATEMENTS

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of Federal Communications Commission (FCC)

Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or TV reception, which can

be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

This device and its antenna must not be co-located or operated in conjunction with

any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Any changes or modications not expressly approved by the party responsible for

compliance could void the authority to operate equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the FCC

radio frequency exposure limits, human proximity to the antenna shall not be less

than 20 cm (8 inches) during normal operation. The equipment version marketed

in the U.S. is restricted to usage of the channels 1-11 only.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/EC of the

European Parliament and the Council of March 9, 1999, on radio equipment

and telecommunication terminal equipment and the mutual recognition of their

conformity (R&TTE). The R&TTE directive repeals and replaces Directive 98/13/

EEC (Telecommunications Terminal Equipment and Satellite Earth Station

Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install

and use it. However, special attention must be paid to the dangers of electric shock

and static electricity when working with electrical equipment. All guidelines must

therefore be followed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and ofce use in Austria,

Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,

the Netherlands, Portugal, Spain, Sweden and the United Kingdom. The ETSI

version of this device is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

EU Countries Not Intended for Use

None.

Safe Operating Guidelines

• The Wireless 150N PCI Card is designed for indoor use only. Do not expose this

card to direct sunlight, rain or snow.

• Do not place or use this card in or near excessively hot or humid places, such as

kitchens or bathrooms.

• This card can become hot when used for long time. This is normal and is not a

malfunction. Do not place the card on paper, cloth or other ammable materials

after extended use.

• There are no user-serviceable parts inside the card. If the card isn’t working

properly, contact your place of purchase and ask for help. Do not disassemble the

card yourself, as doing so will void the warranty.

• If the card falls into water, do not use it again before it’s inspected by an authorized

technician, as recommended by your place of purchase.

• If strange odors or smoke emanate from the card, immediately switch the

computer off and call your place of purchase for help.

CONTENTS

TABLE OF CONTENTS

section page

1 HARDWARE .........................................................................................................................6

1.1 Card Components ..........................................................................................................6

1.2 Installing the Card ..........................................................................................................6

2 DRIVER INSTALLATION ......................................................................................................7

3 CONFIGURATION ..............................................................................................................11

3.1 Network Settings ..........................................................................................................11

3.1.1 INTELLINET Cong Utility .....................................................................................12

3.1.1.1 Scanning for Other Devices ............................................................................12

3.1.1.2 Connecting to an AP .......................................................................................14

3.1.1.3 Adding an AP to Prole List ............................................................................. 15

3.1.2 Using the WZC Utility ............................................................................................20

3.2 Prole Management .....................................................................................................23

3.2.1 Add a Prole ..........................................................................................................24

3.2.2 Edit an Existing Prole ...........................................................................................24

3.2.3 Delete an Existing Prole .......................................................................................24

3.2.4 Activate a Prole ....................................................................................................24

3.3 Advanced Settings .....................................................................................................24

3.4 View Network Statistics .............................................................................................26

3.5 WMM Settings ...........................................................................................................26

3.6 WPS Conguration ....................................................................................................27

3.6.1 PBC .......................................................................................................................28

3.6.2 PIN ........................................................................................................................30

3.7 Radio On/Off .............................................................................................................. 31

3.8 About ........................................................................................................................31

4 SoftAP ........................................................................................................................32

4.1 SoftAP Conguration ..................................................................................................32

4.2 Security Settings ......................................................................................................... 34

4.3 Access Control .............................................................................................................36

4.4 Connection Table .........................................................................................................37

4.5 Event Log .....................................................................................................................37

4.6 Statistics ......................................................................................................................38

4.7 About ........................................................................................................................39

5 TROUBLESHOOTING ........................................................................................................40

6 FREQUENTLY ASKED QUESTIONS ................................................................................. 41

7 SPECIFICATIONS.............................................................................................................. 44

HARDWARE

1 HARDWARE

1.1 Card Components

• Screw the included antenna onto the reverse SMA connector after the card has

been installed on the computer (see below). It’s recommended that the antenna

be positioned at a 90˚ angle to the card initially for what is typically the best radio

reception, adjusting it as needed later.

• Press and hold the WPS button for 3 seconds to start the WPS function. When

WPS is enabled, the Link and Tx/Rx LEDs will light.

• The Tx/Rx LED is yellow and blinks when data is being transferred or received.

When it’s off, there is no wireless activity. When WPS is enabled, this LED remains

on.

• The Link LED is green. It lights when a link has been established to a wireless

access point; it goes off when the radio is switched off. When WPS is enabled,

this LED remains on

1.2 Installing the Card

1. Turn off the computer.

2. Remove the cover.

3. Insert the card into an empty

PCI slot on the computer.

4. Attach the antenna and

position it as directed above.

5. Replace the cover and turn

the computer on.

ANT

WPS

Tx/Rx

Link

DRIVER INSTALLATION

2 DRIVER INSTALLATION

Once the Wireless 150N PCI Card is installed and the computer is turned back on,

the Welcome to the Found New Hardware Wizard screen will display. Click “Cancel”

and proceed with the driver installation procedure below.

Insert the included setup CD and run the Setup.exe program.

2. When the License Agreement screen displays, read the agreement, select “I

accept the terms of the license agreement” and click “Next.”

DRIVER INSTALLATION

3. It’s recommended that both the driver and utility be installed from the Setup Type

screen if the card is being installed on this computer for the rst time. Select

“Install driver only” if you prefer. Click “Next”to continue.

4. On the second Setup Type screen, it’s recommended that you select “INTELLINET

Conguration Tool,” as it provides full access to all the functions of this card. If

you prefer to use the wireless conguration tool provided by Windows XP or

Vista, select “Microsoft Zero Conguration Tool.” Click “Next.”

DRIVER INSTALLATION

3. It’s recommended that both the driver and utility be installed from the Setup Type

screen if the card is being installed on this computer for the ﬁ rst time. Select

“Install driver only” if you prefer. Click “Next”to continue.

4. On the second Setup Type screen, it’s recommended that you select “INTELLINET

Conﬁ guration Tool,” as it provides full access to all the functions of this card. If

you prefer to use the wireless conﬁ guration tool provided by Windows XP or

Vista, select “Microsoft Zero Conﬁ guration Tool.” Click “Next.”

INTELLINET

Install driver and INTELLINET WLAN Utility

INTELLINET

INTELLINET Conﬁ guration Tool

DRIVER INSTALLATION

3. It’s recommended that both the driver and utility be installed from the Setup Type

screen if the card is being installed on this computer for the ﬁ rst time. Select

“Install driver only” if you prefer. Click “Next”to continue.

4. On the second Setup Type screen, it’s recommended that you select “INTELLINET

Conﬁ guration Tool,” as it provides full access to all the functions of this card. If

you prefer to use the wireless conﬁ guration tool provided by Windows XP or

Vista, select “Microsoft Zero Conﬁ guration Tool.” Click “Next.”

INTELLINET

Install driver and INTELLINET WLAN Utility

INTELLINET

INTELLINET Conﬁ guration Tool

DRIVER INSTALLATION

5. When the Ready to Install the Program screen displays, click “Install.” If another

Found New Hardware screen displays instead, wait a moment for the program

to update, then continue. After you click “Install,” wait for the program to run.

6. When the nal utility screen displays, click “Finish” to complete the driver

installation process.

DRIVER INSTALLATION

5. When the Ready to Install the Program screen displays, click “Install.” If another

Found New Hardware screen displays instead, wait a moment for the program

to update, then continue. After you click “Install,” wait for the program to run.

6. When the ﬁ nal utility screen displays, click “Finish” to complete the driver

installation process.

INTELLINET

the INTELLINET WLAN Utility. Click Finish

to exit the wizard.

DRIVER INSTALLATION

5. When the Ready to Install the Program screen displays, click “Install.” If another

Found New Hardware screen displays instead, wait a moment for the program

to update, then continue. After you click “Install,” wait for the program to run.

6. When the ﬁ nal utility screen displays, click “Finish” to complete the driver

installation process.

INTELLINET

the INTELLINET WLAN Utility. Click Finish

to exit the wizard.

DRIVER INSTALLATION

Once installation is complete, the

wireless conguration utility displays

on the computer desktop and as an

INTELLINET icon in the systems tray. Mouse-over the icon to learn the card status.

To congure your wireless

connection, right-click on the

icon to display the popup menu.

Click “Launch Cong Utility” to

start the conguration program.

To close the utility, click “Exit.”

NOTE: If you click “Exit” to close the conguration utility, you won’t be able to

maintain the wireless link to the access point you want to use. In this case, you can

re-launch the utility by going to Start on the desktop and clicking the Wireless

Utility option, as shown below.

DRIVER INSTALLATION

Once installation is complete, the

wireless conﬁ guration utility displays

on the computer desktop and as an

INTELLINET icon in the systems tray. Mouse-over the icon to learn the card status.

To conﬁ gure your wireless

connection, right-click on the

icon to display the popup menu.

Click “Launch Conﬁ g Utility” to

start the conﬁ guration program.

To close the utility, click “Exit.”

NOTE: If you click “Exit” to close the conﬁ guration utility, you won’t be able to

maintain the wireless link to the access point you want to use. In this case, you can

re-launch the utility by going to Start on the desktop and clicking the Wireless

Utility option, as shown below.

INTELLINET Wireless Utility

INTELLINET Wireless

DRIVER INSTALLATION

Once installation is complete, the

wireless conﬁ guration utility displays

on the computer desktop and as an

INTELLINET icon in the systems tray. Mouse-over the icon to learn the card status.

To conﬁ gure your wireless

connection, right-click on the

icon to display the popup menu.

Click “Launch Conﬁ g Utility” to

start the conﬁ guration program.

To close the utility, click “Exit.”

NOTE: If you click “Exit” to close the conﬁ guration utility, you won’t be able to

maintain the wireless link to the access point you want to use. In this case, you can

re-launch the utility by going to Start on the desktop and clicking the Wireless

Utility option, as shown below.

INTELLINET Wireless Utility

INTELLINET Wireless

DRIVER INSTALLATION

Once installation is complete, the

wireless conﬁ guration utility displays

on the computer desktop and as an

INTELLINET icon in the systems tray. Mouse-over the icon to learn the card status.

To conﬁ gure your wireless

connection, right-click on the

icon to display the popup menu.

Click “Launch Conﬁ g Utility” to

start the conﬁ guration program.

To close the utility, click “Exit.”

NOTE: If you click “Exit” to close the conﬁ guration utility, you won’t be able to

maintain the wireless link to the access point you want to use. In this case, you can

re-launch the utility by going to Start on the desktop and clicking the Wireless

Utility option, as shown below.

INTELLINET Wireless Utility

INTELLINET Wireless

CONFIGURATION

3 CONFIGURATION

Once the driver is installed, it will automatically try to connect to any unencrypted

wireless access point. If you want to connect to a specic wireless access point, or

if the access point you want to connect to uses encryption, you need to congure

the Wireless 150N PCI Card and input the required parameters rst.

The current status of your wireless connection is indicated by the appearance of

the conguration utility icon.

The wireless connection is established: good signal reception.

The wireless connection is established: normal signal reception.

The wireless connection is established: weak signal reception.

The connection is not established yet or was lost.

The wireless network card is not detected

3.1 Network Settings

Right-click the conguration utility icon on the desktop to display the popup menu;

then click “Launch Cong Utility” (as shown on Page 10). The utility will automatically

begin to scan for all wireless access points and display a Network screen.

As mentioned in Section 2: Driver Installation, there are two ways to congure the

card to connect to a wireless access point: using the INTELLINET conguration

utility and using Windows’ built-in Microsoft Zero Conguration Tool. Both options

are detailed below

CONFIGURATION

3 CONFIGURATION

Once the driver is installed, it will automatically try to connect to any unencrypted

wireless access point. If you want to connect to a speciﬁ c wireless access point, or

if the access point you want to connect to uses encryption, you need to conﬁ gure

the Wireless 150N PCI Card and input the required parameters ﬁ rst.

The current status of your wireless connection is indicated by the appearance of

the conﬁ guration utility icon.

The wireless connection is established: good signal reception.

The wireless connection is established: normal signal reception.

The wireless connection is established: weak signal reception.

The connection is not established yet or was lost.

The wireless network card is not detected

3.1 Network Settings

Right-click the conﬁ guration utility icon on the desktop to display the popup menu;

then click “Launch Conﬁ g Utility” (as shown on Page 10). The utility will automatically

begin to scan for all wireless access points and display a Network screen.

As mentioned in Section 2: Driver Installation, there are two ways to conﬁ gure the

card to connect to a wireless access point: using the INTELLINET conﬁ guration

utility and using Windows’ built-in Microsoft Zero Conﬁ guration Tool. Both options

are detailed below

INTELLINET_UI

CONFIGURATION

3.1.1 INTELLINET Conguration Utility

All utility screens present a menu of function options — Prole, Network, etc. —

across the top. The Network screens feature a setup window below the menu

section, which expands in depth automatically to accommodate information that

corresponds to the current card activity. TIP: You can also expand the setup window

by clicking the “More/Less” up/down arrow button at the bottom-right of the screen

(clicking it again to revert back to the original window size).

3.1.1.1 Scanning for Other Wireless Devices

There are two kinds of wireless connection mode: Infrastructure and Ad-Hoc.

Infrastructure mode is used by wireless access points, which are able to establish

wireless connections for you and other wireless or wired network clients.

Ad-Hoc mode is also known as Point-to-Point mode. In this mode, wireless devices

such as computers or PDAs will not be capable of establishing wireless connections

with more than one wireless device, and so is suitable for establishing a one-to-one

wireless connection between two wireless devices.

Before you can connect to any wireless access point or device by Infrastructure or

Ad-Hoc mode, there two pieces of information you need to have:

• The wireless device’s SSID, or service set identier (which you can think of as an

access point’s name). You can scan for the SSID of other wireless devices nearby,

but if the SSID of the wireless device you want to connect to is hidden, you need

to know it — exactly — before you can establish a connection with it.

• The wireless device’s encryption key (if it uses encryption).

When the scan results are displayed in the setup window, check that the wireless

device (access point or another computer) with the SSID you want to connect to is

included.

Scan results include several pieces of information:

• The wireless device’s SSID is displayed to the left (KEN, 6F in the example above).

If nothing appears, it means the SSID of that device is hidden. When a connection

is established, a blue arrow ( ) displays to the left of the SSID.

• The type and channel number of the wireless device, depicted by if it’s an AP

or by if it’s a computer (Ad-Hoc mode, point-to-point connection)

• The wireless standard supported by this access point: “n” for 802.11n; “g” for

802.11g; and “b” for 802.11b. Additionally, the WPS icon ( ) will appear when the

access point supports WPS; a key icon ( ) will appear if the access point uses

CONFIGURATION

3.1.1 INTELLINET Conﬁ guration Utility

All utility screens present a menu of function options — Proﬁ le, Network, etc. —

across the top. The Network screens feature a setup window below the menu

section, which expands in depth automatically to accommodate information that

corresponds to the current card activity. TIP: You can also expand the setup window

by clicking the “More/Less” up/down arrow button at the bottom-right of the screen

(clicking it again to revert back to the original window size).

3.1.1.1 Scanning for Other Wireless Devices

There are two kinds of wireless connection mode: Infrastructure and Ad-Hoc.

Infrastructure mode is used by wireless access points, which are able to establish

wireless connections for you and other wireless or wired network clients.

Ad-Hoc mode is also known as Point-to-Point mode. In this mode, wireless devices

such as computers or PDAs will not be capable of establishing wireless connections

with more than one wireless device, and so is suitable for establishing a one-to-one

wireless connection between two wireless devices.

Before you can connect to any wireless access point or device by Infrastructure or

Ad-Hoc mode, there two pieces of information you need to have:

• The wireless device’s SSID, or service set identiﬁ er (which you can think of as an

access point’s name). You can scan for the SSID of other wireless devices nearby,

but if the SSID of the wireless device you want to connect to is hidden, you need

to know it — exactly — before you can establish a connection with it.

• The wireless device’s encryption key (if it uses encryption).

When the scan results are displayed in the setup window, check that the wireless

device (access point or another computer) with the SSID you want to connect to is

included.

Scan results include several pieces of information:

• The wireless device’s SSID is displayed to the left (KEN, 6F in the example above).

If nothing appear

s, it means the SSID of that device is hidden. When a connection

is established, a blue arrow ( ) displays to the left of the SSID.

• The type and channel number of the wireless device, depicted by if it’s an AP

or by if it’s a computer (Ad-Hoc mode, point-to-point connection)

• The wireless standard supported by this access point: “n” for 802.11n; “g” for

802.11g; and “b” for 802.11b. Additionally, the WPS icon ( ) will appear when the

access point supports WPS; a key icon ( ) will appear if the access point uses

CONFIGURATION

encryption. NOTE: When the access point supports WPS and the WPS icon

appears, you won’t see the key icon here even through the access point uses

encryption.

• The signal strength of the access point as a percentage (100% = full strength).

• The signal strength of the access point as a bar graph (as a visual comparison).

If you don’t see the access point you want, click “Rescan” until the AP you prefer is

displayed. If rescanning doesn’t nd the AP you want after ve tries, move your

computer closer to the access point or refer to Section 5: Troubleshooting.

To see detailed information about a specic access point, double-click on it. The

expanded screen presents four more packets of information in addition to the

options and details already displayed.

Sorted by >> — You can sort all listed access points: by SSID, channel or signal

(strength).

Show dBm — Check this box to show the signal strength in decibels instead of as

a percentage.

CONFIGURATION

encryption. NOTE: When the access point supports WPS and the WPS icon

appears, you won’t see the key icon here even through the access point uses

encryption.

• The signal strength of the access point as a percentage (100% = full strength).

• The signal strength of the access point as a bar graph (as a visual comparison).

If you don’t see the access point you want, click “Rescan” until the AP you prefer is

displayed. If rescanning doesn’t ﬁ nd the AP you want after ﬁ ve tries, move your

computer closer to the access point or refer to Section 5: Troubleshooting.

To see detailed information about a speciﬁ c access point, double-click on it. The

expanded screen presents four more packets of information in addition to the

options and details already displayed.

Sorted by >> — You can sort all listed access points: by SSID, channel or signal

(strength).

Show dBm — Check this box to show the signal strength in decibels instead of as

a percentage.

INTELLINET_UI

CONFIGURATION

Rescan — Click to rescan for access points.

Add to Prole — To store a specic access point in the Prole List (see Section 3.1.3:

Add an Access Point to Prole) so that you can link to it directly without entering

the authentication key again, select the AP, then click “Add to Prole.”

Connect — Click to connect to whichever access point is selected on the list.

General —Displays basic information about the selected access point, such as

SSID, MAC address, authentication/encryption type, channel and such.

WPS — If this access point supports WPS (Wi-Fi Protected Setup), related

information is displayed here.

CCX —If this access point supports CCX (Cisco Compatible eXtension), related

information is displayed here.

802.11n — If this access point complies with the 802.11n draft, related information

is displayed here.

3.1.1.2 Connecting to an Access Point

1. Select the wireless access point or network device you want to connect to and

click “Connect.” If the access point you selected doesn’t use encryption, you’ll

be connected to it within a minute. If it does use encryption, go to Step 3.

2. If the wireless access point doesn’t show

an SSID, you’ll be prompted to enter it.

NOTE: If you need to obtain the SSID

from the owner of the wireless access

point you’re connecting to, make sure it’s

exact or the connection won’t work. Once you’ve entered the SSID, click “OK.”

3. If the wireless access point uses encryption, you will be prompted to enter its

WEP key or WPA preshared key. NOTE: If you need to obtain the key from the

owner of the device you’re connecting to, make sure it’s exact or the connection

CONFIGURATION

Rescan — Click to rescan for access points.

Add to Proﬁ le — To store a speciﬁ c access point in the Proﬁ le List (see Section 3.1.3:

Add an Access Point to Proﬁ le) so that you can link to it directly without entering

the authentication key again, select the AP, then click “Add to Proﬁ le.”

Connect — Click to connect to whichever access point is selected on the list.

General —Displays basic information about the selected access point, such as

SSID, MAC address, authentication/encryption type, channel and such.

WPS — If this access point supports WPS (Wi-Fi Protected Setup), related

information is displayed here.

CCX —If this access point supports CCX (Cisco Compatible eXtension), related

information is displayed here.

802.11n — If this access point complies with the 802.11n draft, related information

is displayed here.

3.1.1.2 Connecting to an Access Point

1. Select the wireless access point or network device you want to connect to and

click “Connect.” If the access point you selected doesn’t use encryption, you’ll

be connected to it within a minute. If it does use encryption, go to Step 3.

2. If the wireless access point doesn’t show

an SSID, you’ll be prompted to enter it.

NOTE: If you need to obtain the SSID

from the owner of the wireless access

point you’re connecting to, make sure it’s

exact or the connection won’t work. Once you’ve entered the SSID, click “OK.”

3. If the wireless access point uses encryption, you will be prompted to enter its

WEP key or WPA preshared key. NOTE: If you need to obtain the key from the

owner of the device you’re connecting to, make

sure it’s exact or the connection

INTELLINET_UI

CONFIGURATION

Rescan — Click to rescan for access points.

Add to Proﬁ le — To store a speciﬁ c access point in the Proﬁ le List (see Section 3.1.3:

Add an Access Point to Proﬁ le) so that you can link to it directly without entering

the authentication key again, select the AP, then click “Add to Proﬁ le.”

Connect — Click to connect to whichever access point is selected on the list.

General —Displays basic information about the selected access point, such as

SSID, MAC address, authentication/encryption type, channel and such.

WPS — If this access point supports WPS (Wi-Fi Protected Setup), related

information is displayed here.

CCX —If this access point supports CCX (Cisco Compatible eXtension), related

information is displayed here.

802.11n — If this access point complies with the 802.11n draft, related information

is displayed here.

3.1.1.2 Connecting to an Access Point

1. Select the wireless access point or network device you want to connect to and

click “Connect.” If the access point you selected doesn’t use encryption, you’ll

be connected to it within a minute. If it does use encryption, go to Step 3.

2. If the wireless access point doesn’t show

an SSID, you’ll be prompted to enter it.

NOTE: If you need to obtain the SSID

from the owner of the wireless access

point you’re connecting to, make sure it’s

exact or the connection won’t work. Once you’ve entered the SSID, click “OK.”

3. If the wireless access point uses encryption, you will be prompted to enter its

WEP key or WPA preshared key. NOTE: If you need to obtain the key from the

owner of the device you’re connecting to, make sure it’s exact or the connection

INTELLINET_UI

CONFIGURATION

won’t work. Check the “Show Password” box to display the key you enter.

The authentication type will be selected automatically by the access point: Don’t

change it. However, if you’re connecting to an AP using 802.1x authentication,

you need to select “802.1x” and enter the related information as explained later.

4. If the connection is successful, the blue arrow displays to the left of the SSID.

Remember, you can mouse-over

the conguration utility icon to

display a popup that tells you the

connection quality/status, and you can click the “More/Less” button

to expand the screen and see more detailed information.

3.1.1.3 Adding an Access Point to the Prole List

If you expect to connect to a specic wireless access point frequently, you can add

its information to the Prole List and recall it whenever you want to establish the

connection. You can add a found access point to the Prole List, or you can enter

the information of an AP manually.

To add a found AP to the Prole List, simply select it and click “Add to Prole.”

CONFIGURATION

won’t work. Check the “Show Password” box to display the key you enter.

The authentication type will be selected automatically by the access point: Don’t

change it. However, if you’re connecting to an AP using 802.1x authentication,

you need to select “802.1x” and enter the related information as explained later.

4. If the connection is successful, the blue arrow displays to the left of the SSID.

Remember, you can mouse-over

the conﬁ guration utility icon to

display a popup that tells you the

connection quality/status, and you can click the “More/Less” button (

)

to expand the screen and see more detailed information.

3.1.1.3 Adding an Access Point to the Proﬁ le List

If you expect to connect to a speciﬁ c wireless access point frequently, you can add

its information to the Proﬁ le List and recall it whenever you want to establish the

connection. You can add a found access point to the Proﬁ le List, or you can enter

the information of an AP manually.

To add a found AP to the Proﬁ le List, simply select it and click “Add to Proﬁ le.”

INTELLINET_UI

CONFIGURATION

won’t work. Check the “Show Password” box to display the key you enter.

The authentication type will be selected automatically by the access point: Don’t

change it. However, if you’re connecting to an AP using 802.1x authentication,

you need to select “802.1x” and enter the related information as explained later.

4. If the connection is successful, the blue arrow displays to the left of the SSID.

Remember, you can mouse-over

the conﬁ guration utility icon to

display a popup that tells you the

connection quality/status, and you can click the “More/Less” button (

)

to expand the screen and see more detailed information.

3.1.1.3 Adding an Access Point to the Proﬁ le List

If you expect to connect to a speciﬁ c wireless access point frequently, you can add

its information to the Proﬁ le List and recall it whenever you want to establish the

connection. You can add a found access point to the Proﬁ le List, or you can enter

the information of an AP manually.

To add a found AP to the Proﬁ le List, simply select it and click “Add to Proﬁ le.”

INTELLINET_UI

CONFIGURATION

won’t work. Check the “Show Password” box to display the key you enter.

The authentication type will be selected automatically by the access point: Don’t

change it. However, if you’re connecting to an AP using 802.1x authentication,

you need to select “802.1x” and enter the related information as explained later.

4. If the connection is successful, the blue arrow displays to the left of the SSID.

Remember, you can mouse-over

the conﬁ guration utility icon to

display a popup that tells you the

connection quality/status, and you can click the “More/Less” button (

)

to expand the screen and see more detailed information.

3.1.1.3 Adding an Access Point to the Proﬁ le List

If you expect to connect to a speciﬁ c wireless access point frequently, you can add

its information to the Proﬁ le List and recall it whenever you want to establish the

connection. You can add a found access point to the Proﬁ le List, or you can enter

the information of an AP manually.

To add a found AP to the Proﬁ le List, simply select it and click “Add to Proﬁ le.”

INTELLINET_UI

CONFIGURATION

won’t work. Check the “Show Password” box to display the key you enter.

The authentication type will be selected automatically by the access point: Don’t

change it. However, if you’re connecting to an AP using 802.1x authentication,

you need to select “802.1x” and enter the related information as explained later.

4. If the connection is successful, the blue arrow displays to the left of the SSID.

Remember, you can mouse-over

the conﬁ guration utility icon to

display a popup that tells you the

connection quality/status, and you can click the “More/Less” button (

)

to expand the screen and see more detailed information.

3.1.1.3 Adding an Access Point to the Proﬁ le List

If you expect to connect to a speciﬁ c wireless access point frequently, you can add

its information to the Proﬁ le List and recall it whenever you want to establish the

connection. You can add a found access point to the Proﬁ le List, or you can enter

the information of an AP manually.

To add a found AP to the Proﬁ le List, simply select it and click “Add to Proﬁ le.”

INTELLINET_UI

CONFIGURATION

To enter the information for an access point manually, go to the Prole menu (see

Section 3.2: Prole Management) and click “Add.”

The screen will expand as needed, initially displaying the System Cong screen.

Prole Name — Every prole needs a unique name.

SSID — Enter the SSID of this access point. If you selected an access point from

the Prole List and its SSID isn’t hidden, the SSID will be lled automatically;

however, you can modify the SSID manually.

Network Type — Select Ad Hoc or Infrastructure. If you’re connecting to an access

point, select “Infrastructure”; for point-to-point wireless connection (i.e., you’re

connecting to another computer that’s using Ad Hoc mode), select “Ad Hoc.”

NOTE: If you selected an AP from the Prole List, keep this eld unchanged.

Tx Power — This is the wireless output power. If you’re not too far from an access

point (good signal reception), you can select a lower output power to save energy;

for a more distant access point, select a higher output power. NOTE: “Auto” is

suggested to let the utility decide the best output power setting.

CONFIGURATION

To enter the information for an access point manually, go to the Proﬁ le menu (see

Section 3.2: Proﬁ le Management) and click “Add.”

The screen will expand as needed, initially displaying the System Conﬁ g screen.

Proﬁ le Name — Every proﬁ le needs a unique name.

SSID — Enter the SSID of this access point. If you selected an access point from

the Proﬁ le List and its SSID isn’t hidden, the SSID will be ﬁ lled automatically;

however, you can modify the SSID manually.

Network Type — Select Ad Hoc or Infrastructure. If you’re connecting to an access

point, select “Infrastructure”; for point-to-point wireless connection (i.e., you’re

connecting to another computer that’s using Ad Hoc mode), select “Ad Hoc.”

NOTE: If you selected an AP from the Proﬁ le List, keep this ﬁ eld unchanged.