Channel Vision CMS-IP-Cameras User manual

Category
Digital Video Recorders (DVR)
Type
User manual
1/53
User Manual
IPCamera Recorder
2/53
Index
I. PREFACE................................................................................................................................................ 4
II. SYSTEM REQUIREMENTS ................................................................................................................ 4
A. MINIMUM REQUIREMENTS......................................................................................................................... 4
B. SUGGESTED REQUIREMENTS...................................................................................................................... 5
III. PROGRAM INSTALL AND UNINSTALL.......................................................................................... 5
A. PROGRAM INSTALL .................................................................................................................................... 5
B. UNINSTALL ................................................................................................................................................ 8
IV. SET UP FRONT-END DEVICE & HDD.............................................................................................. 8
A. SET UP IP CAMERA/ VIDEO SERVER / DIGITAL VIDEO RECORDER .............................................................. 8
B. SET UP HDD TO RECORD THE VIDEO ........................................................................................................ 14
V. LIVE VIDEO MONITORING ............................................................................................................ 16
VI. VIDEO PLAYBACK ............................................................................................................................ 19
A. VIDEO PLAYBACK .................................................................................................................................... 19
B. EXPORT VIDEO......................................................................................................................................... 21
VII. DIGITAL ZOOM.................................................................................................................................. 22
VIII. E-MAP ................................................................................................................................................... 23
A. MAP ......................................................................................................................................................... 23
B. TREE VIEW .............................................................................................................................................. 24
C. EVENT RECORD ....................................................................................................................................... 24
IX. REMOTE CONTROL ......................................................................................................................... 25
A. WEB SERVER .......................................................................................................................................... 25
B. REMOTELITE .......................................................................................................................................... 31
X. OTHERS ............................................................................................................................................... 33
A. SCHEDULE RECORD SETTING.................................................................................................................... 33
B. MOTION DETECTION................................................................................................................................34
C. PTZ SET UP AND CONTROL ....................................................................................................................... 34
D. I/O SETUP................................................................................................................................................. 36
E. MOTION/ ALARM EVENT SETUP.............................................................................................................. 36
F. SYSTEM ................................................................................................................................................... 38
G. PASSWORD SETUP .................................................................................................................................... 44
3/53
H. E-MAP SETTING ........................................................................................................................................ 45
XI. CONFIGURE TOOL ........................................................................................................................... 47
A. MONITOR RESOLUTION (DEFAULT: ON) ................................................................................................... 47
B. ENABLE/ DISABLE “WINDOW CONTROL (DEFAULT: OFF) ................................................................ 47
C. ENABLE/ DISABLE “PC TIME (DEFAULT: ON).......................................................................................... 48
D. ENABLE/ DISABLE “PING (DEFAULT: OFF) .............................................................................................. 48
E. ENABLE/ DISABLE “OVERLAY (DEFAULT: ON) ........................................................................................ 48
F. BACKUP CONFIGURATIONS ....................................................................................................................... 49
XII. PRODUCT SPECIFICATIONS ..........................................................................................................50
XIII. GRAPHIC CARD TEST TABLE...................................................................................................... 53
4/53
I. Preface
IPCamera Recorder (includes 1,4,9,16 and 36 channels) is a video recording
software which supports IP Camera, Video Server and Digital Video Recorder.
People use IPCamera Recorder to monitor the real-time video, record the video on
PC then playback the recorded video when necessary.
IPCamera Recorder supports 5 different ways to record the video, including
normal recording, schedule recording, motion-triggered recording, alarm-triggered
recording and manual recording. Moreover, E-Map and Multi-Monitor are the
build-in functions within IPCamera Recorder.
Via activating the function of web server, IPCamera Recorder provides web
browser and RemoteLite program for user demand.
II. System Requirements
A. Minimum Requirements
i. CPU: Intel Pentium 4 2.0G
ii. Memory: 1GB
iii. VGA card: 128MB External Graphic Card or above
iv. Monitor Resolution: 1024 x 768
v. OS: Windows Vista/ XP / 2000
vi. File System: NTFS*
(*IPCamera Recorder still can operate in FAT32 file system. However, it
will waste much time while set up the volume of hard disk and it is worse
when write the recording data into the hard disk. Therefore, FAT32 file
system is not suggested to use.)
5/53
B. Suggested Requirements
i. CPU: Intel Core 2 Quad Q6600 or above
ii. Memory: 2GB
iii. VGA card: 256MB External Graphic Card or above
iv. Monitor Resolution: 1024 x 768
v. OS: Windows Vista/ XP/ 2000
vi. File System: NTFS
III. Program Install and Uninstall
A. Program Install
i. To install IPCamera Recorder, please double click .
ii. Please select the language for the requirement. Currently, IPCamera
Recorder supports ”Tradition Chinese”, “Simple Chinese”,
“English” ,“Polish”, “Japanese” and “German” six sorts of languages.
iii. License Agreement. Select “I Agree”Go to the next step.
6/53
iv. Select the directory for IPCamera Recorder. The default installation
directory is "C:\Program Files\IPCamera Recorder". Select “Next”.
v. Set up the name of the program folder. The default is “IPCamera
Recorder”. Click “Install” to start the installation.
7/53
vi. When finish, click “Close” to close the procedure of the installation.
vii. To start the program, select “Start” Æ”Program”Æ””IPCamera
Recorder ”Æ”IPCamera Recorder”. In Windows Vista, please right-click
on the short cut icon of IPCamera Recorder or the main program, then
select “Run as administrator” to start the program.
Please refer to following example which is based on 36H IPCamera
Recorder.
viii. Additional monitor screen might be seen if second monitor is connected.
ix. In the IPCamera Recorder, the first and the second live-viewing screens
are similar, but the number of the channels displayed on the screen
might be different.
8/53
x. If multi-monitor is not supported by PC, the multi-monitor mode
and the multi-monitor ON/OFF will be inactivated.
B. Uninstall
i. To uninstall the program, select “Start” Æ ”Program” Æ”IPCamera
Recorder”Æ”Uninstall” to remove the program.
IV. Set up front-end device & HDD
To start recording, please set up the IP camera/ Video server & HDD.
A. Set up IP Camera/ Video Server /
Digital Video Recorder
There are 2 ways to set up the IP Camera/ Video Server
i. Configure Tool
a. Select “Start”Æ ”Program” Æ ”IPCamera Recorder”
Æ ”Tools”Æ ”Configure tool”. In Windows Vista, please right-click on
the desktop short cut or configure tool, then select “Run as
administrator” to start the program.
9/53
b. “Configure tool” integrates “IPInstaller”. When start “Configure tool”,
it will search IP camera & video server automatically. To re-search
the device, please click “Scan IP”.
c. Select the IP camera/ video server you would like to add.
Drag-and-drop to the video channel listed above. Then type the
username & password of the device.
d. When finish the configuration, click “Save” to save all the
information.
ii. Set up IP camera/ video server in the administration page
a. Select to enter IP camera/ video server set up page.
Note: The following examples are base on 36CH IPCamera
Recorder.
10/53
b. There are 18 channels listed on the left side of the administrator
page. Users can use to switch 1-18, 19-36 channels.
Moreover, users can use either keyboard to enter the setup values,
or the mouse to click to activate the virtual keyboard to
configure each channel.
c. Camera can be configured in the general setup page. First, click
to enable each channel and to set each camera.
d. Please select channel type (Normal or Attached):
Normal: The same as the main setup page.
Attached: If user selects one channel as attached channel type,
user has to select video source. Moreover, due to the
attached channel is not physically linked to any camera;
it will not cost any bandwidth loading.
11/53
Application of attached channel: Attached channel type can
operate with the digital zoom function. User can select different
spots in the main channel and attach to different attached channels.
Because attached channel type is not physically linked to any
camera; such channel will not cost any loading of camera or HDD
space. For instance, the following figure shows that CH2, 3 and 4
are only three parts of the CH1.
e. In the basic setting as showed below, channel name can be saved
in the “Channel Tag” to distinguish each channel. IP address is
indicating the channel. With IP Share (Router), the Port needed to
be adjusted in case of conflict. Fills in the ID and the Password for
each channel, then click to connect each device or channel.
12/53
Click will enable IE to browse each channel.
f. Within the Image setup page as showed below, users can alter
image Resolution, Quality, Video Format, and Frame Rate.
g. In the Pre & Post Alarm Recording setting page as showed below,
users can change the recording time interval.
h. In the Information setting page as showed belowTag / Date / Time
can be displayed on the live viewing
i. In the Display setting page as showed belowusers can select
display mode.
13/53
When is selected, only I-Frame will be
transferred and displayed in live-viewing; Enabling
will cause live-viewing to display the original
image size (as showed below).
j. In the Audio setting as showed belowclicks “Enable Audio” to
enable audio recording.
k. Before exiting administration page, remember to click
to
save all the configurations.
l. Moreover, in advanced setup, click to setup the tag, Date
/Time and status location of each shown channel. Click
within advanced setting can setup such as the size, format and
color of tag, Date/Time and status.
NOTE: The advanced setting will apply to all shown channels.
14/53
B. Set up HDD to record the video
To record the video on PC, HD space is better to be set first. Or, IPCamera
Recorder will perform the record by the default setting (Based on the HD space).
i. Start the program, enter administration page and click button to
the disk setup page.
ii. Before the space is set, the default setting path is the folder, Record,
which the software installed. Moreover, the default setting of available
data storage quantity is No Limitation.
iii. If the new recording path would be added, click button to add the
new recording path. In contrast, click button to delete the
recording path.
iv. To add the new recording path, click button first.
v. Then, use the mouse to select the path and click button to
complete the setting. The image is shown in the following,
1
2
3
15/53
vi. After complete the new recording path setting, click / (Up
and Down) to select the sequence of the recording path. While the disk
space of the priority path is full, the recorded data will be reserved in the
next path.
vii. To mount the available space, click the data recording path first. Then,
click / of the “Available (MB)” to mount the space. Moreover, use
the keyboard can mount the space as well.
viii. Finally, click to reserve all the settings.
16/53
V. Live Video Monitoring
i. IPCamera Recorder supports the following real-time monitoring mode.
a. 36 Channel IPCamera Recorder can switch 36-CH ,
16-CH , 9-CH , 4-CH , 1-CH , and
multi-monitor (16CH each).
ii. : Enable/Disable multi-monitor.
iii. : Full Screen mode. To exit the full screen mode, use “Esc” or
right-click the mouse.
iv. : Minimize the program.
v. : Auto rotating channel. Users can set switching time interval
and determine the initial screen split value
.
vi.
: Manual recording. To start recording immediately. Moreover, to
click the button again can stop recording.
vii.
: Recorded video playback.
viii. : Get into administration page.
17/53
ix. : Get into E-Map
x. : Close the program
xi. It shows the status of each channel.
Indicate the video recording status.
Indicate Motion Detection.
Indicate Alarm status.
xii. : PTZ controller interface. Provides
FocusZoomIRISAuto/ Stop Patrol and Preset Point control.
xiii. : DVR Control Panel. When
the selected channel is DVR, It will show the control panel to control
DVR, such as change split, playback and so on.
xiv. : Digital Zoom Control Panel. After selected
the channel, the extra image zoom window will be displayed to control
the digital zoom in/out.
xv. : I/O switch. There are up to 4 I/O controls. ( if remote device
supported)
xvi. : Chatting switch. On/Off 2-way audio (if remote device
supported).
xvii. : Broadcast switch. On/Off broadcast function (if remote
device supported).
18/53
xviii. : 04CH MPEG4 DVR Playback Control Panel.
When selected channel is 04CH MPEG4 DVR module, the control panel
will reveal. Click button can perform playback via time and event
searches as following:
19/53
VI. Video Playback
Click to enter video playback mode.
Note: The following example is based on 36CH IPCamera Recorder.
A. Video Playback
i. Use calendar to select the date. As shown in the following figure, the
“day” means there are recorded data in that day. For example, there are
videos in 2007/07/20.
ii. After selecting the date, please click
to select the video
channel you would like to play (36CH version).
20/53
IPCamera Recorder supports different kinds of playback mode.
Currently, IPCamera Recorder supports up to four channels
synchronized and asynchronized playback.
iii. When choose the date and video channel, it will show the recording
status.
a. No color: No video data.
b. Red: Normal recording data.
c. Yellow: Motion-triggered recording data.
d. Blue: Alarm-triggered recording data.
e. Gray: The time you choose to play.
iv. Click to start playback. Click to pause it
v. Use to fasten the speed. 1x, 2x, 4x, 8x, 16x and 32x available
(depends on the hardware and total channels).
vi. Use to go to previous/ next frame.
vii. Check “Asynchronize Play” to enable different time and channel
playback.
viii. Check “Show tag”, “Show time” to show title & time on each channel.
ix. Check “Disable Digital Zoom” to see the original size of the video.
x. Check “Event List” to see the event records.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53

Channel Vision CMS-IP-Cameras User manual

Category
Digital Video Recorders (DVR)
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI