Graco 333113B Inline Filter User manual

333113B Inline Filter
Graco
Brand
Graco
Model
333113B Inline Filter
Type
User manual

This manual is also suitable for

Graco 333113B Inline Filter is designed for professional use in centralized grease lubrication systems. It features a maximum lubricant inlet pressure of 5000 psi (34.47 MPa, 344 bar) and 3/8 inch NPT inlet and outlet. The filter element (part number 77X523) has a 400-micron rating and can be easily replaced. The filter assembly also includes two o-rings (part number 77X541) to ensure a leak-proof seal.

Graco 333113B Inline Filter is designed for professional use in centralized grease lubrication systems. It features a maximum lubricant inlet pressure of 5000 psi (34.47 MPa, 344 bar) and 3/8 inch NPT inlet and outlet. The filter element (part number 77X523) has a 400-micron rating and can be easily replaced. The filter assembly also includes two o-rings (part number 77X541) to ensure a leak-proof seal.

333113B
Instructions
Inline Filter
For use in centralized grease lubrication systems. For professional use only.
5000 psi (34.47 MPa, 344 bar) Maximum Lubricant Inlet Pressure
3/8 inch npt inlet and outlet
400 microns
Part No.: 77X523
Filter Element and Seal Kit: 77X541
Important Safety Instructions
Read all warnings and instructions in this man-
ual and the pump or lubrication system instruc-
tion manual. Save all instructions.
Ref Description Qty
1 FILTER, element
1
2 PACKING, o-ring
1
3 PACKING, o-ring
1
1
2
Cross Section
EN
3
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 333113
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2013, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
revised February 2014
Installation
Install filter with flow arrow (a) pointing in the direction
the grease flows through the system as shown in F
IG. 1.
Replacing Filter Element
.
1. Relieve pressure. See your pump or lubrication sys-
tem instruction manual.
2. Remove filter assembly from installation location.
3. Use a wrench to remove nut (b) (F
IG. 1).
4. Remove filter and o-rings (2 and 3) as shown in
Cross Section of filter assembly on page 1.
5. Clean inside of filter body to remove contaminants.
6. Insert new filter (1) and new o-rings (2 and 3).
7. Replace nut (a) (F
IG. 1). Torque to 40 ft. lb + 10 ft. lb
(54 N.m +
13.5 N.m).
8. Reinstall filter assembly in installation location.
Graco Information
To place an order, contact your Graco distributor or to identify the nearest distributor call,
Toll Free: 1-800-533-9655, Fax: 612-378-3590
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury
from pressurized fluid, such as skin injection,
splashing fluid and moving parts, follow the
Pressure Relief Procedure provided in your pump
or lubrication system instruction manual when you
stop dispensing and before cleaning, checking, or
servicing the equipment.
FIG. 1
b
a
  • Page 1 1
  • Page 2 2

Graco 333113B Inline Filter User manual

333113B Inline Filter
Graco
Brand
Graco
Model
333113B Inline Filter
Type
User manual
This manual is also suitable for

Graco 333113B Inline Filter is designed for professional use in centralized grease lubrication systems. It features a maximum lubricant inlet pressure of 5000 psi (34.47 MPa, 344 bar) and 3/8 inch NPT inlet and outlet. The filter element (part number 77X523) has a 400-micron rating and can be easily replaced. The filter assembly also includes two o-rings (part number 77X541) to ensure a leak-proof seal.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents