SunBrite SB-CM46A12 Owner's manual
- Category
- Wall & ceiling mounts accessories
- Type
- Owner's manual
This manual is also suitable for
SunBrite SB-CM46A12 is designed for all-weather use. It’s an adjustable ceiling mount compatible with up to 125 lbs displays, it has adjustable length extension column, it allows up to 20 degrees of face tilt up and down and can be used for both indoor and outdoor installations.
SunBrite SB-CM46A12 is designed for all-weather use. It’s an adjustable ceiling mount compatible with up to 125 lbs displays, it has adjustable length extension column, it allows up to 20 degrees of face tilt up and down and can be used for both indoor and outdoor installations.
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
All-Weather Flat Panel Ceiling Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SB-CM46A12
SB-CM46A12 Installation Instructions
2
DISCLAIMER
SunBriteTV LLC (SBTV) intends to make this manual accurate
and complete. However, SBTV makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. SBTV makes no
representation of warranty, expressed or implied, regarding the
information contained herein. SBTV assumes no responsibility
for accuracy, completeness or sufficiency of the information
contained in this document.
SunBriteTV® is a registered trademark of SunBrite TV LLC.
Built to SunBriteTV® specifications by Chief Manufacturing. All
rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the SB-CM46A12 mount up
to (and including) the display does not exceed 125 lbs (56.7
kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
IMPORTANT ! :
The SB-CM46A12 is designed to be mounted
to 2" x 4" wood stud joists.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
4.22
107.2
6.21
157.7
1.25
31.8
FACE TILTS
UP &
20
DOWN
1 1/2" NPT
1 1/2" NPT
4 ADJUSTMENTS IN
1" INCREMENTS
4.19
106.4
0.406
10.3
DIMENSIONS: INCHES
[MILLIMETERS]
Installation Instructions SB-CM46A12
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
SB-CM46A12 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/4"
3/16" (included)
5/32" (included)
1/8" (included)
D (1)
3/16"
A (1)
B (1)
[ceiling plate]
E (1)
5/32"
F (4)
3/8"
[adjustable column]
G (1)
[faceplate]
H (1)
5/16-18 x 3/8"
J (2)
[side bracket]
K (2)
[center bracket]
L (8)
#10-24 x 1/2"
N (1)
1/8"
M (4)
[mounting button]
C (1)
5/16 x 1/4"
Installation Instructions SB-CM46A12
5
INSTALLATION
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
1. Using ceiling plate (B) as a template, mark locations of two
pilot holes. (See Figure 1) Ensure the following:
• Use OPPOSITE holes in plate (B), and
• Marks are in the center of wood joist.
NOTE: Drywall not shown for clarity.
Figure 1
2. Drill 1/4" diameter pilot holes into wood joist. (See Figure 2)
Ensure pilot holes are straight.
Figure 2
3. Using 9/16" socket wrench, loosely install two (minimum)
Grade 2 (not included) 3/8" x 2-1/2" lag screws through 3/8"
washers (F), ceiling plate (B), into wood joist (See Figure 2).
Do not tighten plate (B) against ceiling at this time to
accommodate cable installation.
NOTE: Two additional washers are provided.
4. Route cables through channel in ceiling plate (B). (See
Figure 3)
Figure 3
5. Tighten lag screws. (See Figure 2)
1
x 2
(B)
3
x 2
2
x 2
5
(B)
(F) x 2
4
(B)
SB-CM46A12 Installation Instructions
6
ADJUSTABLE LENGTH EXTENSION
COLUMN
1. Install adjustable column (A) into plate. (See Figure 4)
Securely tighten column.
• Ensure column (A) engages four full threads into plate.
• Ensure cable access opening is rotated to desired
position (optional installation, column (A)).
Figure 4
2. Secure column (A) by tightening set screw (C) in plate using
3/16" hex key (D). (See Figure 4)
NOTE: Two adjustment holes provided in interior (fixed)
column. Either adjustment hole can be used to provide
1" (25mm) adjustment increments.
3. (Optional) Remove button head cap screw and supporting
washers from lower adjustment hole if an additional 1"
(25mm) adjustment increment is desired. (See Figure 5)
4. (Optional) Replace button head cap screw and supporting
washers into upper adjustment hole to provide an additional
1" (25mm) adjustment increment. (See Figure 5)
Figure 5
5. Adjust column (A) to desired length, then rotate and lock
into position. (See Figure 5)
NOTE: Any locking slot can be used to provide 1" (25mm)
adjustment increments.
6. Tighten adjustment screw using 3/16" hex key (D). (See
Figure 5)
7. Tighten set screws on back of pipe using 3/16" key (D).
(See Figure 6)
NOTE: Optional installation similar; not shown.
Figure 6
4 x
1
1
4 x
(A)
2
(C)
(B)
4
6
5
(A)
3
7
x 2
(rear view)
Installation Instructions SB-CM46A12
7
Attaching Faceplate to Pipe
CAUTION: Watch for pinch points. Do not place fingers
between moveable parts.
1. Thread the faceplate (G) onto pipe (A) until tight. (See
Figure 7)
2. Install and tighten the 5/16-18 x 3/8" set screw (H) using the
5/32" hex key (E). (See Figure 7)
Figure 7
Interface Bracket Assembly
1. Use four #10-24 x 1/2" button head cap screws (L) and 1/8"
hex key (N) to attach four mounting buttons (M) to two
center brackets (K). (See Figure 8)
2. Use four #10-24 x 1/2" button head cap screws (L) and 1/8"
hex key (N) to attach side brackets (J) to center brackets
(K). (See Figure 8)
Figure 8
Display Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.
WARNING: OVERTIGHTENING OF SCREWS CAN
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
cup!
1. Remove the four mounting screws and washers that came
installed on the back of the display. (See Figure 9)
2. Use four removed screws and washers to attach side
brackets (N) to display. (See Figure 9)
Figure 9
(G)
(A)
2
1
(H) x 1
(L) x 4
2
(J) x 2
(K) x 2
(L) x 4
1
(M) x 4
2
x 4
1
removed screws x 4
(J) x 2
SB-CM46A12 Installation Instructions
8
3. While supporting both sides of display, align four mounting
buttons (M) on display or interface bracket with four
mounting holes on faceplate (G). (See Figures 10, 11 and
12)
Figure 10
WARNING: DISPLAY WEIGHS IN EXCESS OF 40 LBS!
Always use two people and proper lifting techniques when
installing or positioning display.
4. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons (M) are properly
seated in lower area of mounting holes. (See Figures 10, 11
and 12)
Figure 11
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting
buttons are completely engaged in mounting holes.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 12)
Figure 12
Removing Display
1. Disconnect all power/audio/video cables.
2. Remove bolt or padlock from faceplate (if used).
(See Figure 13)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
3. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 13)
WARNING: THE DISPLAY WEIGHS IN EXCESS OF 40
LBS EACH! Always use two people and proper lifting
techniques when installing or positioning display.
4. Carefully lift display from faceplate.
5. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 13)
3
(G)
Display
Back of
display
(J) x 2
(M) x 4
(G)
4
5
May remove
pin and nut and
move to lower holes
A padlock or bolt
may be placed
through latch holes
Installation Instructions SB-CM46A12
9
Figure 13
Adjusting Display
CAUTION: Watch for pinch points. Do not place fingers
between moveable parts.
Adjusting Roll
1. Using a 9/16" wrench, loosen the Nylock roll adjustment nut
on back of mounting plate. (See Figure 14)
2. Tilt the faceplate left or right as required.
3. TIghten nut.
NOTE: Do NOT overtighten fasteners.
Adjusting Pitch
1. Adjust display to the desired pitch.
2. Using the 5/32" hex head wrench (E), tighten the pitch
adjustment screw to hold mount in position. (See Figure 14)
Figure 14
2
1
4
Pin in
"Closed"
position -
Move to
"Open"
position to
remove
display
Remove bolt
or padlock
if used
Pin in
"Open"
position -
Move to
"Closed"
position
after display
is removed
Roll
Adjustment
Nut
Pitch
Adjustment
Screw
SB-CM46A12 Installation Instructions
10
Installation Instructions SB-CM46A12
11
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
SunBrite SB-CM46A12 Owner's manual
- Category
- Wall & ceiling mounts accessories
- Type
- Owner's manual
- This manual is also suitable for
SunBrite SB-CM46A12 is designed for all-weather use. It’s an adjustable ceiling mount compatible with up to 125 lbs displays, it has adjustable length extension column, it allows up to 20 degrees of face tilt up and down and can be used for both indoor and outdoor installations.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SunBrite SB-CM32A12 Owner's manual
-
-
SunBriteTV SB-WM46 User manual
-
-
-
-
-
SunBrite SB-CM-DT-L-BL Owner's manual
-
SunBriteTV SB-V-75-4KHDR-BL Quick start guide
-
Other documents
-
-
-
-
-
-
-
-
Chief PTS2064 User manual
-
Chief Manufacturing CMA-300 User manual
-
Chief C-Clamp Installation guide