Sony SWF-BR100 Owner's manual

Page is loading ...

2

US

Warning

To reduce the risk of fire or

electric shock, do not expose this

apparatus to rain or moisture.

The unit not disconnect form the mains

as long as it is connected to the AC

outlet, even if unit itself has been turned

off.

To reduce the risk of fire, do not cover

the ventilation opening of the appliance

with newspapers, tablecloths, curtains,

etc.

Do not expose the appliance to naked

flame sources (for example, lighted

candles).

To reduce the risk of fire or electric

shock, do not expose this appliance to

dripping or splashing, and do not place

objects filled with liquids, such as vases,

on the appliance.

As the main plug is used to disconnect

the unit from the mains, connect the

unit to an easily accessible AC outlet.

Should you notice an abnormality in the

unit, disconnect the main plug from the

AC outlet immediately.

Do not install the appliance in a confined

space, such as a bookcase or built-in

cabinet.

In door use only.

For the customers in the U.S.A

This symbol is intended to alert

the user to the presence of

uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

This symbol is intended to alert

the user to the presence of

important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

Owner’s Record

The model and serial numbers are

located on the rear exterior of the unit.

Record the serial numbers in the space

provided below. Refer to them

whenever you call upon your Sony

dealer regarding this product.

Model No.

Serial No.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near

water.

6) Clean only with dry cloth.

7) Do not block any ventilation slit on

the backside. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources

such as radiators, heat registers,

stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of

the polarized or grounding-type

plug. A polarized plug has two

blades with one wider than the

other. A grounding type plug has

two blades and a third grounding

prong. The wide blade or the third

prong are provided for your safety. If

the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and

the point where they exit from the

apparatus.

SWF-BR100

For customers in USA and Canada

3

US

11) Only use attachments/accessories

specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during

lightning storms or when unused for

long periods of time.

14) Refer all servicing to qualified service

personnel. Servicing is required

when the apparatus has been

damaged in any way, such as

power-supply cord or plug is

damaged, liquid has been spilled or

objects have fallen into the

apparatus, the apparatus has been

exposed to rain or moisture, does

not operate normally, or has been

dropped.

The following FCC statement applies

only to the version of this model

manufactured for sale in the U.S.A.

Other versions may not comply with FCC

technical regulations.

NOTE:

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are

designed to provide reasonable

protection against harmful interference

in a residential installation. This

equipment generates, uses and can

radiate radio frequency energy and, if

not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does

cause harmful interference to radio or

television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to try

to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving

antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced

radio/TV technician for help.

Properly shielded and grounded cables

and connectors must be used for

connection to host computers and/or

peripherals in order to meet FCC

emission limits.

CAUTION

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

This equipment must not be co-located

or operated in conjunction with any

other antenna or transmitter.

Compliance with FCC requirement

15.407(c)

Data transmission is always initiated by

software, which is the passed down

through the MAC, through the digital

and analog baseband, and finally to the

RF chip. Several special packets are

initiated by the MAC. These are the only

ways the digital baseband portion will

turn on the RF transmitter, which it then

turns off at the end of the packet.

Therefore, the transmitter will be on only

while one of the aforementioned

packets is being transmitted. In other

words, this device automatically

discontinues transmission in case of

either absence of information to

transmit or operational failure.

4

US

Frequency Tolerance: ±20ppm or less

5.15-5.25GHz band is restricted to indoor

operations only.

This equipment complies with FCC

radiation exposure limits set forth for an

uncontrolled environment and meets the

FCC radio frequency (RF) Exposure

Guidelines. This equipment should be

installed and operated keeping the

radiator at least 20cm or more away from

person’s body (excluding extremities:

hands, wrists, feet and ankles).

For UWT-BR100

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions:(1) this device

may not cause harmful interference, and

(2) this device must accept any

interference received, including

interference that may cause undesired

operation

.

For the customer in Canada

This device complies with Industry

Canada license-exempt RSS standard(s).

Operation is subject to the following two

condition: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of the device.

5.15-5.25GHz band is restricted to indoor

operations only.

This equipment complies with IC

radiation exposure limits set forth for an

uncontrolled environment and meets

RSS-102 of the IC radio frequency (RF)

Exposure rules. This equipment should

be installed and operated keeping the

radiator at least 20cm or more away from

person’s body (excluding extremities:

hands, wrists, feet and ankles).

Properly shielded and grounded cables

and connectors must be used for

connection to host computers and/or

peripherals.

Caution

This product is designed for use with

Sony TV. You should only use this

product on a compatible Sony TV.

Please read these safety instructions to

ensure your personal safety and prevent

property damage.

On safety

 Should any solid object or liquid fall

into the subwoofer, unplug the

subwoofer and have it checked by

qualified personnel before operating

it any further.

 Do not climb on the subwoofer, as you

may fall down and injure yourself, or

subwoofer damage may result.

 Before operating the subwoofer, check

that the operating voltage is identical

to your local power supply.

 If you are not going to use the

subwoofer for a long time, be sure to

disconnect the subwoofer from the

wall outlet (mains). To disconnect the

AC power cord (mains lead), grasp the

plug itself; never pull the cord.

 AC power cord (mains lead) must be

changed only at the qualified service

shop.

On placement

 Place the subwoofer in a location with

adequate ventilation to prevent heat

buildup and prolong the life of the

subwoofer.

 Do not place the subwoofer near heat

sources, or in a place subject to direct

sunlight, excessive dust, or mechanical

shock.

 Use caution when placing the

subwoofer on surfaces that have been

specially treated (with wax, oil, polish,

etc.) as staining or discoloration of the

surface may result.

 Take care to avoid any possible injury

on the corners of the subwoofer.

5

US

 Please keep the back panel (a side

with the switch) away from the wall

more than 5cm. Prevent something

like cloth from blocking up the

ventilation slit.

Ventilation slit

On operation

Before connecting other equipment, be

sure to turn off and unplug the

subwoofer.

On cleaning

Clean the subwoofer with a soft dry

cloth. Do not use any type of abrasive

pad, scouring powder or solvent such as

alcohol or benzine.

If you have any question or problem

concerning your subwoofer, please

consult your nearest Sony dealer.

Setting up the

Wireless System

Wireless Transceiver

TV

Wireless

Subwoofer

Audio

cable

1 Connect the audio

cable (supplied) to the

Wireless Transceiver.

2 Connect the other end

of the audio cable to

the AUDIO OUT

/

jack of the TV.

3 Connect the Wireless

Transceiver to a USB

port

of the TV.

~

The wireless transceiver may interfere

with other terminals on TV physically,

depending on the position of USB

terminal you connected.

4 Connect the AC power

cord (mains lead) from

the subwoofer to the

AC power outlet.

~

It is recommended that the Subwoofer is

placed as close as possible to the TV.

5 The subwoofer will

automatically turns on

and the / indicator

lights in green when

the TV is turned on.

1

2

/ (on/standby) button,

indicator

SECURE button

6

US

Using the

subwoofer

About the power state

The subwoofer would be turned

on automatically when you turn

on the TV.

Then it would enter standby mode

and the / indicator lights in red,

when the TV is in standby mode.

You can also turn the subwoofer to

standby mode by TV’s menu,

during TV is turned on.

If you want to turn off the

subwoofer, you can operate by

/ button on the subwoofer. /

indicator would not light up during

the subwoofer is turned off.

About the sound

adjustment

You can adjust subwoofer level,

cut-off frequency and phase by

TV’s menu.

Refer to the TV’s instruction

manual.

Activating wireless

transmission

between specific

units

You can specify the wireless

connection to be used to link the

Wireless Transceiver to the

subwoofer using the Secure Link

function.

This function is useful when you

use multiple wireless products.

1 Press SECURE button on

the Wireless

Transceiver (the LED

indicator lights and

flashes in amber).

1

2

LED

SECURE button

2 Press SECURE button on

the rear of the

subwoofer (the LED

indicator lights and

flashes in amber).

7

US

3 Both LEDs light in solid

turns into amber, and

the subwoofer makes

bass sound.

To cancel this

operation, press the

button again.

Proceed the step 2 within 2

minutes.

Cancelling the

Secure Link

function

Press and hold SECURE

button on the Wireless

Transceiver for several

seconds until the LED

indicator turns off.

~

If the LED indicator on the Subwoofer

is still blinking amber, press and hold

SECURE button on the rear of the

subwoofer for several seconds until the

/ indicator turns green or flashes in

green.

Additional

Information

Troubleshooting

If you experience any of the

following difficulties while using

the system, use this

troubleshooting guide to help

remedy the problem before

requesting support. Should any

problem persist, consult your

nearest Sony dealer. When

bringing the system in for repairs,

be sure to bring in the entire

system. This product is a system

product, and the entire system is

needed to determine the part

requiring repair.

No TV sound is output from

the subwoofer.

 Check the connection of the audio

cable that is connected to the

wireless transceiver and the TV.

 Check the sound output of the TV.

When sound does not come out,

confirm the sound output settings

of the TV and the volume of the TV

speaker.

 Check the status of / indicator on

the subwoofer:

 Turns off.

- Check that the AC power cord

(mains lead) of the subwoofer is

securely connected.

- Turn the subwoofer on by

pressing / button on the

subwoofer.

8

US

 Stays lit in red:

- Check the location of the

subwoofer.

- Do not place the TV and

subwoofer in a metal cabinet.

- Place the subwoofer close to the

TV in a room.

- Make sure that the wireless

transceiver is inserted correctly

into the TV.

- Please confirm that power

setting of Wireless Subwoofer of

TV is Auto.

 Flashes in green or amber slowly

or turns red:

- Make the Secure Link setting

again.

- Sound transmission is poor.

Move the subwoofer so that the

power indicator turns green or

amber.

 Flashes in red:

- Press power to turn off the

subwoofer, and check that

nothing is blocking the

ventilation slit of the subwoofer.

A protection function may act by

excessive input. Please lower TV

volume or the SW level.

Noise is heard from the

subwoofer or sound from the

subwoofer is intermittent.

 Move the subwoofer closer to the

TV.

 Do not install the TV and subwoofer

in a closed rack, on a metal rack, or

under a table.

 Move the subwoofer away from

other wireless devices.

 Avoid using any other wireless

devices.

The sound output from the

subwoofer is very low.

 Check the subwoofer level in the

sound setting of the TV.

 With some types of content such as

news there will not be a lot of bass

sound, this is normal.

Specifications

Wireless Subwoofer

(SWF-BR100)

Amplifier section

For U.S.A model:

(FTC)

With 4 ohms load, subwoofer

channel driven, from 30 - 150 Hz;

rated 45 W per channel minimum

RMS power, with no more than 1%

total harmonic distortion from 250

milliwatts to rated output.

POWER OUTPUT (reference)

100 W (per channel at 4 ohms,

100 Hz)

For Canadian and Mexican model:

POWER OUTPUT (rated)

70 W (4 ohms, 100 Hz, 1% THD)

POWER OUTPUT (reference)

100 W (4 ohms, 100 Hz)

Speaker System

Subwoofer, sealed enclosure

Speaker Unit

200 mm cone type

Rated impedance

4 ohms

Power requirements

120 V AC, 60 Hz

Power consumption

On: 30W

Standby mode: 0.5W or less

Dimensions (approx.) (w/h/d)

272 mm x 305 mm x 395 mm

10 3/4 in x 12 1/8 in x 15 5/8 in

Mass (approx.)

12.2kg

26 lb 14 3/10 oz

9

US

Wireless Transceiver

(UWT-BR100)

Communication system

Wireless Sound Specification

version 3.0

Frequency band

5GHz band

(5.180/5.200/5.210/5.240GHz,

5.736/5.762/5.814GHz)

The frequency bands used depend

on the country.

Modulation method

DSSS

Power requirement

5V DC

Power consumption

500 mA

Dimensions (approx.)

19 mm x 27 mm x 91 mm

3/4 in x 1 1/8 in x 3 5/8 in

(w/h/d)

Mass (approx.)

25g

7/8oz

Supplied accessories

Audio cable (1)

Design and specifications are

subject to change without notice.

Page is loading ...

http://www.sony.net/

4-488-516-41(1)

Printed in Malaysia

Sony SWF-BR100 Owner's manual

Sony SWF-BR100 Owner's manual

in other languages

Related papers

Other documents