Niles Audio GSS10 User manual

Brand: Niles Audio

Model: GSS10

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

Speaker GSS10

Niles Audio Speaker GSS10 is a high-quality subwoofer designed for outdoor use. It features a 10" mineral-filled polypropylene woofer that delivers deep, powerful bass. The GSS10 is also weather-resistant and can be buried underground for a truly immersive audio experience. With a recommended amplifier power of 50-500 watts, the GSS10 can be used with a variety of amplifiers to create a custom audio system that meets your specific needs.

garden speakers

GSS10 INSTALLATION GUIDE

WWW.NILESAUDIO.COM

Thank you for purchasing the GSS10 In-ground subwoofer from Niles. With

proper installation and operation, you’ll enjoy years of trouble-free use.

Parts List

1 GSS10 Subwoofer

1 GSS10 Bass Port Tube

8 Hex Screws

1 Hex Wrench

tooLs required for instaLLation

Spade, Shovel, or Trench Tool

Wire Strippers

Bubble Level

Direct Burial Rated Speaker Cable

16AWG for wire runs of up to 100 ft

14AWG for wire runs up to 150 ft

12 AWG for wire runs up to 200 ft

oPtionaL features

A 70v transformer kit is available for the GSS10. It is the GSS70V, Niles Part

Number FG01675

Gss10 assembLy

Remove both the subwoofer and the bass port tube

from their packaging. Using the hex wrench provided,

securely attach the port tube to the subwoofer. When

properly oriented, the port tube should be “Up” when

the subwoofer is resting on its base.

Make sure that each of the hex screws is securely

tightened to prevent the possibility of any vibration

or rattling from the subwoofer when installed. Once

assembled, the subwoofer is ready for installation.

introduction

NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992

choosinG a Location

The location of the subwoofer should be

based on three considerations: sound

coverage, ease of installation, and the

ease of running cable to the installation

location. The large 10” woofer cone will

provide impressive bass performance for

a large area when properly placed.

The subwoofer requires a hole with a

width of approximately 14” (36 cm) and a

length of approximately 30” (76 cm). The

depth should be between 16 - 18” (40 –

45 cm). Additionally, burial rated speaker

cable must be run from your subwoofer amplier to the proposed subwoofer

location. Make certain that there are no obstructions in the planned location

or along the proposed wiring location before proceeding. Many states and

municipalities have specic notication requirements before digging. Make sure

to check with your local building authorities as required prior to digging.

Keep in mind when choosing a location that low frequency sounds will permeate

the entire area which means that the subwoofer does not need to be “aimed” or

pointed in any particular direction.

The subwoofer is made of heavy duty uPVC, designed for many years of

rugged outdoor use and will withstand occasional hits from common handheld

landscape tools, but can be damaged by lawn mowers or other motorized

equipment. Placing the subwoofer where it is not likely to be struck by such

equipment will help ensure years of listening enjoyment. This can be easily done

by careful placement of landscaping features around the bass port tube.

Also, please be aware that you can control the bass output by your placement

location. This is called the boundary effect. You will get more bass response

by mounting the GSS10 near a wall or other at surface. You can increase

the bass output even more by mounting the GSS10 in a corner location. This

kind of placement gives the speaker two boundaries, further reinforcing the

bass sounds. Of course, mounting the subwoofer further away from any other

boundaries will minimize this effect. Landscaping walls or other structures

could be utilized for this purpose. A further consideration is that the closer

the subwoofer is placed to the home, the more chance of unwanted vibration

entering the home when the subwoofer is played at large volumes.

Choose the location carefully prior to digging any holes or running any wires.

Once the location has been chosen and the hole has been prepared, place the

Width of approximately

14” (36 cm)

Length of approximately

30” (76 cm).

Depth should be

between 16 - 18”

(40 – 45 cm)

WWW.NILESAUDIO.COM

subwoofer into the hole and verify that it is horizontal using the bubble level. It is

now time to connect the loudspeaker wires to the subwoofer. Before connecting

any loudspeaker wire, make certain that the subwoofer amplier is turned OFF.

Connect the loudspeaker wires to the subwoofer, making certain to match polarity

so that the positive lead from the amplier matches to the positive lead from the

subwoofer and do the same with the negative leads. When connecting the wires,

be sure to use silicone lled wire nuts, or an appropriate water tight connector or

junction box.

Connect the wires to your subwoofer amplier and turn it on to test the

connection. If the loudspeaker sounds ne, you can now ll in the hole around

the GSS10. Keep in mind that the subwoofer will sound slightly different when

fully installed in the ground than it will in an open air environment. Verify the

satisfactory performance of each loudspeaker before covering any exposed

trenches or conduit used for your wiring.

Before proceeding, turn off the amplier for safety.

Carefully pack and compress the dirt around the subwoofer making certain not

to damage either the subwoofer or its wiring. The subwoofer should have rm

support on all sides to prevent any settling in the future.

Should you ever need to service your GSS10 subwoofer, you can use the

Niles Logo located on the top cover to determine where the unit is located

underground. The side of the vent cover with the Niles Logo (

) is the side

where the subwoofer unit is located.

PaintinG

The tube and its dome cover can be painted to match any environment. When

painting the GSS10 port tube, be sure not to paint the underside of the dome.

There are special lter screens that should not be painted over on the underside of

the dome. The top and sides can easily be painted with a high quality spray paint.

recommended amPLifier

The GSS10 is a passive subwoofer designed to be used with a subwoofer

amplier. We recommend the Niles SWA-500M, Part Number FG01361. The

SWA-500M is a high-current design that can power up to 2 GSS10 subwoofers.

NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992

sPecifications

Woofer: 10” Mineral-Filled Polypropylene

Recommended Amplier Power: 50-500 watts

Frequency Response: 25 Hz to 110 Hz

Product Weight: 25 lbs (11.4 kg)

Recommended Burial Depth: 16-18” (40-45 cm)

Max SPL: 110dB

Impedance: 8 ohm nominal, 6 ohm minimum

Temperature Extremes: -50F to 185F (-45° to 85° Celsius)

WWW.NILESAUDIO.COM

notes

NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992

1-800-BUY-HIFI (289-4434)

BY PHONE (IN USA)

CUStOmEr SErvICE HOUrS

8:00 AM to 5:30 PM PT

6:00 AM to 4:00 PM PT

tECHNICAl SUPPOrt HOUrS

www.nilesaudio.com

ON tHE wEB

EmAIl tECHNICAl SUPPOrt

EmAIl fOr PrOdUCt SUggEStIONS

productsuggestions@nilesaudio.com

techsupport@nilesaudio.com

BY PHONE (OUtSIdE USA)

1-760-710-0992

trademarks of The AVC Group, LLC. All other trademarks are the property of their respective

owners. We reserve the right to change specifications, descriptions and prices without notice.

The technical and other information contained herein is not intended to set forth all technical

and other specifications. Designed and engineered in the USA. 9901211 Rev A

1969 Kellogg Avenue, Carlsbad, CA 92008

1-760-710-0992

1-800-BUY-HIFI – www.nilesaudio.com

Niles Audio GSS10 User manual

Brand: Niles Audio

Model: GSS10

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

Speaker GSS10

Download PDF

report

Niles Audio GSS10 User manual

This manual is also suitable for

Niles Audio GSS10 User manual

Related papers

Other documents