Gigabyte T1125P User manual

Brand: Gigabyte

Model: T1125P

Category: Notebooks

Type: User manual

This manual is also suitable for

GIGABYTE T1125 Series Notebook Computer User’s Manual

Release Edition: 2010/12

This manual guides you in setting up and using your new notebook.

Information in the manual has been carefully checked for accuracy and is subject to change without notice.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mecha-

nical, by photocopy, recording, or otherwise, without prior written consent from GIGABYTE.

Trademarks

GIGABYTE™ is registered trademarks of GIGABYTE Technology.

All other brands or product names mentioned in this manual are trademarks or registered trademarks of their respective companies.

English

Safety Instructions

Use the following safety guidelines to help protect yourself and your

notebook.

When Using Your T1125 Notebook Computer

CAUTION: Do not operate your portable computer for an

extended period of time with the base resting directly on

your body. With extended operation, heat can build up in the

base. Allowing sustained contact with the skin can cause

discomfort or a possible burn.

• Do not attempt to service the notebook yourself. Always follow

installation instructions closely.

• Do not carry a battery in your pocket, purse, or other container

where metal objects (such as car keys) could short-circuit the

battery terminals. The resulting excessive current ow can

generate extremely high temperature and may cause burns to

your skin.

• Be sure that nothing rests on your AC adapter's power cable

and that the cable is not located where it can be tripped over or

stepped on.

• While you are using the computer or charging the battery, place

the AC adapter in a ventilated area, like on a desktop or on the

oor. Do not cover the AC adapter with papers or other items that

may prevent ventilation. Also, do not use the AC adapter while it

is inside a carrying case.

• Do not insert objects into the air vent of your notebook computer.

Doing so can cause short-circuiting and may result in re or

electrical shock.

• Use only the AC adapter and batteries that are supplied by

your notebook manufacturer. Using other types of battery or AC

adapter may heighten the risk of re or explosion.

• Incorrectly installed or placed batteries may result in an

explosion.

• Replace only with the same or a compatible battery

recommended by the manufacturer.

• Please discard used batteries according to the manufacturer's

instructions.

• Before you connect your notebook to a power source, ensure

that the voltage rating of the AC adapter matches that of the

available power source.

-115 V/60 Hz in most ofNorth and SouthAmerica and some Far

EasterncountriessuchasSouthKorea.

-100V/50HzineasternJapanand100V/60HzinwesternJapan.

-230V/50HzinmostofEurope,theMiddleEast,andtheFarEast.

• If you use an extension cord with your AC adapter, ensure that

the total ampere rating of all devices plugged into the extension

cord does not exceed its total capacity.

• When removing a battery from your notebook, rst turn off the

system, disconnect the AC adapter from the electrical outlet, and

then remove the battery.

• To avoid risk of an electrical shock, do not connect or disconnect

any cables, or perform any maintenance or reconguration of

this product during a thunderstorm.

• Do not throw batteries into a re, doing so may cause explosion.

Check with local authorities rst for battery disposal instructions.

• When setting up your notebook for work, place it on a level

surface.

English

T1125 SERIES USER’S MANUAL

• When traveling, do not check your notebook as baggage. You

can put your notebook through an X-ray security machine, but

never put your notebook through a metal detector. If you have

your notebook checked by hand, be sure to have a charged

battery ready in case you are asked to turn on your notebook.

• When traveling with the hard drive removed from your notebook,

wrap the drive in an insulated material, such as cloth or paper.

If you have the drive checked by hand, you may be asked to

install the drive into your notebook. Your can have the hard

drive checked through an X-ray machine, but never put the drive

through a metal detector.

• When traveling, do not place your notebook in the overhead

storage compartment where it could shift around. Do not drop

your notebook or subject it to other mechanical shocks.

• Protect your notebook, battery, and hard drive from

environmental hazards such as dirt, dust, food, liquids, extreme

temperature, and direct exposure to sunlight.

• When you move your notebook in environments where there

is a substantial difference of temperature or humidity level,

condensa tion may form on or within your notebook. To avoid

damaging your notebook, please allow sufcient time for the

moisture to evaporate before continuing use of the notebook.

NOTICE:Whentakingyournotebookfromacoldertoawarmerenviron-

mentorviceversa,allowyournotebookenoughtimetoadapttothenew

environmentbeforeturningonpower.

• When unplugging the power cord, please make sure that you

pull on its connector or on its strain relief loop, and not on the

power cord itself. As you pull out the connector, please ensure

that it is pulled out evenly in order not to bend its connecting

pins. Also, be fore you connect the power cord, make sure that

both connectors are correctly oriented and aligned.

• Before you clean your notebook, turn it off rst, unplug it from its

power source, and remove the battery.

• Handle interior components with care. When removing a compo-

nent, please hold it by the edge and not on the connecting pins

(such as the memory module).

When using your telephone equipments, safety instructions

should always be followed in order to prevent re, electrical

shock or injuries, these instructions include:

• Do not use this product near water, for example, near a bathtub,

washing basins, kitchen/laundry sinks, wet basements or swim-

ming pools.

• Avoid using cordless phones during an electrical storm as light-

ening may cause electrical shocks.

• Do not use the telephone to report a gas leak within the leakage

area.

WARNING: Voiding of the Warranty

* If the battery is not properly handled, there may be a risk of ex-

plosion; make sure you are using the same or compatible battery.

* Please discard used batteries according to the instructions given

by the manufacturer.

* Please be aware that use of cracked, severely scratched or poor

quality discs may damage the optical drive and corrupt data in

the disc. Such discs may break while drive operates in high-

speed, in this case, your product warranty may be voided.

English

III

Regulatory Notices

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits

for a Class B digital service, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

Any changes or modications made to this equipment may void the

user’s authority to operate this equipment. This equipment gener-

ates, uses, and can radiate radio frequency energy. If not installed

and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television re-

ception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one

or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiv-

er.

● Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for

help.

● All external cables connecting to this basic unit must be

shielded.

For cables connecting to PCMCIA cards, see the option

manual or installation instructions.

RF Exposure

This equipment must be installed and operated in accordance with

provided instructions and must not be co-located or operating in con-

junction with any other antenna or transmitter. End-users and install-

ers must be provide with antenna installation instructions and trans-

mitter operating conditions for satisfying RF exposure compliance.

English

T1125 SERIES USER’S MANUAL

CE Notice (European Union)

This symbol indicates this T1125 notebook complies with the

EMC Directive and the European Union’s Low Voltage Directive.

This symbol also indicates that T1125 meets the following technical

standards:

• EN 55022 — “Limitations and Methods of Measurement for the

Radio Interferences of Information Technology Equipment.”

• EN 55024 — “Information technology equipment - Immunity char-

acteristics - Limits and methods of measurement.”

• EN 61000-3-2 — “Electromagnetic compatibility (EMC) - Chapter

3: Limits - Section 2: Limits on the harmonic current emissions

(Equipment input current up to and including 16 A per phase).”

• EN 61000-3-3 — “Electromagnetic compatibility (EMC) - Chapter

3: Limits - Section 3: Limits on the voltage uctuations and icker

in low-voltage power supply systems for equipment with rate cur-

rent up to and including 16 A.”

• EN 60950 — “Safety of Information Technology Equipment.”

NOTE: EN 55022 emissions requirements provide for two

classications

• Class A governs commercial use

• Class B is governs residential use

For CB:

• Only use batteries designed for this computer. The wrong battery

type may explode, leak or damage the computer

•

Do not remove any batteries from the computer while it is powered on

• Do not continue to use a battery that has been dropped, or that ap-

pears damaged (e.g. bent or twisted) in any way. Even if the computer

continues to work with a damaged battery in place, it may cause circuit

damage, which may possibly result in re.

• Recharge the batteries using the notebook’s system. Incorrect recharg-

ing may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or

replacement to your service representative or qualied service person-

nel.

• Keep children away from, and promptly dispose of a damaged battery.

Always dispose of batteries carefully. Batteries may explode or leak if

exposed to re, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Afx tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Battery Disposal & Caution

The product that you have purchased contains a rechargeable bat-

tery. The battery is recyclable. At the end of its useful life, under

various state and local laws. It may be illegal to dispose of this bat-

tery into the municipal waste stream. Check with your local solid

waste officials for details in your area for recycling options or proper

disposal.

English

Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type recommended by the manufac-

turer. Discard used battery according to the manufacturer’s instruc-

tions.

BSMI Notice (Taiwan Only)

Most Booktop computers are classied by the Bureau of Standards,

Meteorology and Inspection (BSMI) as Class B information technol-

ogy equipment (ITE).

The symbol above must be attached to the product indicating

compliance with the BSMI standard.

Replaceable Batteries

If an equipment is provided with a replaceable battery, and if re-

placement by an incorrect type could result in an explosion (for ex-

ample, with some lithium batteries), the following applies:

● if the battery is placed in an operator access area, there

shall be a marking close to the battery or a statement in both

the operating and the servicing instructions;

● if the battery is placed elsewhere in the equipment, there

shall be a marking close to the battery or a statement in the

servicing instructions.

This marking or statement shall include the following or similar text:

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS

English

T1125 SERIES USER’S MANUAL

FCC statement

This device has been tested and found to comply with the limits for

a Class B digital device pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This device generates, uses,

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this device does

cause harmful interference to radio or television reception, which can

be determined by turning the device off and on, the user is encour-

aged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/television technician

for help.

Notice: Shielded cables

All connections to other computing devices must be made using

shielded cables to maintain compliance with FCC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.)

certied to comply with the Class B limits may be attached to this

equipment. Operation with non-certied peripherals is likely to result

in interference to radio and TV reception.

Caution

Changes or modications are not expressly approved by the manu-

facturer could void the user's authority, which is granted by the Fed-

eral Communications Commission, to operate this computer.

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

Remarque à l'intention des utilisateurs canadiens

Cet appareil numérique de la classe B est conforme a la norme

NMB-003 du Canada.

Compliant with Russian regulatory certication

МЛ04

Modem notices (only for certain models)

Notice for USA

This equipment complies with Part 68 of the FCC rules. Located on

the modem is a label that contains, among other information, the

FCC Registration Number and Ringer Equivalence Number (REN)

for this equipment. Upon request, you must provide this information to

your telephone company. If your telephone equipment causes harm

to the telephone network, the telephone company may discontinue

your service temporarily. If possible, they will notify you in advance.

But, if advance notice is not practical, you will be notied as soon as

possible. You will also be informed of your right to le a complaint

with the FCC.

Your telephone company may make changes in its facilities,

English

VII

equipment, operations, or procedures that could affect the proper

functioning of your equipment. If they do, you will be notied in

advance to give you an opportunity to maintain uninterrupted

telephone service.

If this equipment should fail to operate properly, disconnect the

equipment from the phone line to determine if it is causing the

problem. If the problem is with the equipment, discontinue use and

contact your dealer or vendor.

Caution:

To reduce the risk of re, use only No. 26 AWG or larger UL Listed or

CSA Certied Telecommunication Line Cord.

TBR 21

This equipment has been approved [Council Decision 98/482/EC

- "TBR 21"] for single terminal connection to the Public Switched

Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided

in different countries, the approval does not, of itself, give an

unconditional assurance of successful operation on every PSTN

termination point. In the event of problems, you should contact your

equipment supplier in the rst instance.

Notice for Australia

For safety reasons, only connect headsets with a telecommunications

compliance label. This includes customer equipment previously

labelled permitted or certied.

Notice for New Zealand

1. The grant of a Telepermit for any item of terminal equipment indicates

only that Telecom has accepted that the item complies with minimum

conditions for connection to its network. It indicates no endorsement

of the product by Telecom, nor does it provide any sort of warranty.

Above all, it provides no assurance that any item will work correctly in

all respects with another item of Telepermitted equipment of a different

make or model, nor does it imply that any product is compatible with

all of Telecom's network services.

2. This equipment is not capable, under all operating conditions,

of correct operation at the higher speeds for which it is designed.

Telecom will accept no responsibility should difculties arise in such

circumstances.

3. Some parameters required for compliance with Telecom's Telepermit

requirements are dependent on the equipment (PC) associated with

this device. The associated equipment shall be set to operate within

the following limits for compliance with Telecom's Specications: a

There shall be no more than 10 call attempts to the same number

within any 30 minute period for any single manual call initiation, and

b The equipment shall go on-hook for a period of not less than 30

seconds between the end of one attempt and the beginning of the

next call attempt.

4. Some parameters required for compliance with Telecom's Telepermit

requirements are dependent on the equipment (PC) associated with

this device. In order to operate within the limits for compliance with

Telecom's specications, the associated equipment

English

VIII

T1125 SERIES USER’S MANUAL

labelled permitted or certied. shall be set to ensure that automatic

calls to different numbers are spaced such that there is not less

than 5 seconds between the end of one call attempt and the

beginning of another.

5. This equipment shall not be set up to make automatic calls to

Telecom's 111 Emergency Service.

6. This device is equipped with pulse dialing while the Telecom

standard is DTMF tone dialing. There is no guarantee that Telecom

lines will always continue to support pulse dialing.

7. Use of pulse dialing, when this equipment is connected to the same

line as other equipment, may give rise to bell tinkle or noise and

may also cause a false answer condition. Should such problems

occur, the user should NOT contact the telecom Fault Service.

8. This equipment may not provide for the effective hand-over of a

call to another device connected to the same line.

9. Under power failure conditions this appliance may not operate.

Please ensure that a separate telephone, not dependent on local

power, is available for emergency use.

LCD pixel statement

The LCD unit is produced with high-precision manufacturing

techniques. Nevertheless, some pixels may occasionally misre or

appear as black or red dots. This has no effect on the recorded image

and does not constitute a malfunction.

Radio device regulatory notice

General

To prevent radio interference to the licensed service, this device is

intended to be operated indoors.

This product complies with the radio frequency and safety standards

of any country or region in which it has been approved for wireless

use. Depending on congurations, this product may or may not

contain wireless radio devices (such as wireless LAN and/or

Bluetooth modules). Below information is for products with such

devices.

Declaration of Conformity for EU countries

Hereby, GIGABYTE, declares that this notebook PC series is in

compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC.

List of applicable countries

EU member states as of July 2009 are: Belgium, Denmark, Germany,

Greece, Spain, France, Ireland, Italy, Luxembourg, the Netherlands,

Austria, Portugal, Finland, Sweden, United Kingdom, Estonia, Latvia,

Lithuania, Poland, Hungary, Czech Republic, Slovak Republic,

Slovenia, Cyprus, Malta, Bulgaria and Romania. Usage allowed in

the countries of European Union, as well as Norway,

Switzerland,

Iceland and Liechtenstein. This device must be used in strict

accordance with the regulations and constraints in the country of

use. For further information, please contact local ofce in the country

of use. Please see http://ec.europa.eu/enterprise/rtte/ implem.htm

for the latest country list.

English

The FCC RF safety requirement

The radiated output power of the wireless LAN Mini PCI Card and

Bluetooth card is far below the FCC radio frequency exposure

limits. Nevertheless, the notebook PC series shall be used in such a

manner that the potential for human contact during normal operation

is minimized as follows:

1 Users are requested to follow the RF safety instructions on wireless

option devices that are included in the user's manual of each RF

option device.

Caution: To comply with FCC RF exposure compliance

requirements, a separation distance of at least 20 cm (8 inches)

must be maintained between the antenna for the integrated

wireless LAN Mini PCI Card built in to the screen section and all

persons.

Note:

The wireless Mini PCI adapter implements a transmission

diversity function. The function does not emit radio frequencies

simultaneously from both antennas. One of the antennas is

selected automatically or manually (by users) to ensure good

quality radiocommunication.

2 This device is restricted to indoor use due to its operation in the

5.15 to5.25 GHz frequency range. FCC requires this product to be

used indoors for the frequency range 5.15 to 5.25 GHz to reduce

the potential for harmful interference to co-channel Mobile Satellite

systems.

3 High power radar are allocated as primary users of the 5.25 to 5.35

Hzand 5.65 to 5.85 GHz bands. These radar stations can cause

interference with and/or damage this device.

4 An improper installation or unauthorized use may cause harmful

interference to radio communications. Also any tampering of the

internal antenna will void the FCC certication and your warranty.

Canada — Low-power license-exempt radio communication

devices (RSS-210)

Exposure of humans to RF elds (RSS-102)

The notebook PC series employs low gain integral antennas that do

not emit RF eld in excess of Health Canada limits for the general

population; consult Safety Code 6, obtainable from Health Canada's

website at www.hc-sc.gc.ca/rpb.

This device complies with RSS210 of Industry Canada.

This Class B digital apparatus complies with Canadian ICES-003,

Issue 4, and RSS-210, No 4 (Dec 2000) and No 5 (Nov 2001).

English

T1125 SERIES USER’S MANUAL

Cet appareil numérique de la classe B est conforme à la norme

NMB-003, No. 4, et CNR-210, No 4 (Dec 2000) et No 5 (Nov 2001).

"To prevent radio interference to the licensed service, this device is

intended to be operated indoors and away from windows to provide

maximum shielding. Equipment (or its transmit antenna) that is

installed outdoors is subject to licensing."

« Pour empêcher que cet appareil cause du brouillage au service

faisant l'objet

d'une licence, il doit être utilisé a l'intérieur et devrait être placé loin

des fenêtres an de fournir un écran de blindage maximal. Si le

matériel (ou son antenne d'émission) est installé à l'extérieur, il doit

faire l'objet d'une licence.

Caution:

When using IEEE 802.11a wireless LAN, this product is restricted to

indoor use due to its operation in the 5.15- to 5.25-GHz frequency

range.

Industry Canada requires this product to be used indoors for the

frequency range of 5.15 GHz to 5.25 GHz to reduce the potential

for harmful interference to co-channel mobile satellite systems. High

power radar is allocated as the primary user of the 5.25- to 5.35-

GHz and 5.65 to 5.85-GHz bands. These radar stations can cause

interference with and/or damage to this device.

The maximum allowed antenna gain for use with this device is 6dBi

in order to comply with the E.I.R.P limit for the 5.25- to 5.35 and 5.725

to 5.85 GHz frequency range in point-to-point operation.

LCD panel ergonomic specications

Design viewing distance 500 mm

Design inclination angle 0.0°

Design azimuth angle Pixel fault class

Viewing direction range class Class IV

Screen tilt angle 85.0°

Design screen illuminance

• Illuminance level:

[250 + (250cos∂)] lx where

∂ = 85°

• Color: Source D65

Reection class of LCD panel

(positive and negative polarity)

• Ordinary LCD: Class I

• Protective LCD: Class III

Image polarity Both

Reference white:

Pre-setting of luminance and

color temperature @ 6500K

(tested under BM7)

• Yn

• u'n

• v'n

Pixel fault class Class II

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

English

XII

English

XIII

T1125 SERIES USER’S MANUAL

Introduction

Congratulations and thank you for purchasing the GIGABYTE

T1125 series notebook computer. This portable notebook

comput er provides excellent expansion capability thanks

to the docking station, includes multimedia functionality,

and is de signe d t o pr ovid e re liabl e, no fu ss co mputi ng.

This manual will tell you how to setup and begin using your

T1125. It provides basic configuring, operations and care, and

troubleshooting.

English

XIV

Content

Safety Instructions .............................................................................I

Regulatory Notices & Certications .................................................III

Introduction ....................................................................................XIII

Chapter 1 Knowing Your T1125 Series Notebook

1.1 Top View ..................................................................................2

1.2 Left View ..................................................................................3

1.3 Right View ...............................................................................3

1.4 Base View ................................................................................4

Chapter 2 Using the T1125

2.1 The T1125 Keyboard ...............................................................6

2.2 Use your T1125 as a Tablet PC ..............................................8

2.3 The T1125 Quick Battery Life Test ..........................................8

2.4 Operating Temperature ...........................................................8

Chapter 3 T1125 Specications

3.1 The T1125 Series Notebook Specications ..........................10

Chapter 4 The T1125 Utilities

4.1 GIGABYTE Smart Switch ......................................................12

4.2 GIGABYTE Smart Recovery .................................................12

4.3 GIGABYTE Smart Setup .......................................................13

4.4 GIGABYTE Smart Manager ..................................................13

4.5 GIGABYTE Utility Driver Disc ................................................15

Chapter 5 Troubleshooting / Q&A

5.1 Troubleshooting .....................................................................18

5.2 Frequently Asked Questions .................................................21

5.3 Questions and Answers .........................................................23

5.4 The Notebook Care ...............................................................24

5.5 GIGABYTE Service Information ............................................24

English

T1125 SERIES USER’S MANUAL

Chapter 1 Knowing Your T1125

Series Notebook

This chapter will show you the various ports and components of the

T1125 and familiarizes you with the notebook. Certain parts of the

notebook can be user upgraded while others are xed and cannot

be changed.

English

1.1 Top View

1 2 3

4 5 6

8 9

# Icon Item Description

Web Camera

Web camera for video communication.

Microphone

Internal microphone for sound recording.

LCD Display

Displays computer output.

Keyboard

For entering data into your computer.

Touchpad

Touch-sensitive pointing device which

functions like a computer mouse.

Click Buttons

The left and right buttons function like the left

and right mouse buttons.

Num. Lock

Indicator

Indicates the Notebook’s embedded numeric

keyboard status for numeric data input.

Caps Lock

Indicator

Indicates the Notebook’s input are all capital

letters.

WWAN Indicator

Indicates when the 3.5G device is active.

(3.5G module may be optional)

Bluetooth Status

LED

Indicates when the Bluetooth device is active.

Wireless LAN

Status LED

Indicates when the WiFi LAN device is active.

HDD Status LED

Indicates when the hard disk drive is active.

Battery Status

LED

Flash when charging, and off when the

battery is full.

Power Status

LED

Indicates the Notebook’s power status.

Microphone Jack Accepts inputs from external microphones.

Headphone Jack

Connects to audio line-out devices such as

speakers and headphones.

English

T1125 SERIES USER’S MANUAL

1.2 Left View

1 2 3 4 5 6

# Icon Item Description

DC-in Jack Connects to an AC adapter.

Ethernet Port

Connects to an Ethernet 10/100/1000

Base-T

Docking Port

Connects to the Docking station for

extension functions.

(Docking may be optional).

External Display

(VGA) port

Connects to a display device such as

external monitor or LCD projector.

/ eSATA

eSATA\USB 2.0

Combo Port

The combo port doubles as an

eSATA and a USB port allowing USB

devices and External Hard Drives to

be connected using just one port.

Power Button Turns the computer on and off.

1.3 Right View

1 2 4 53

# Icon Item Description

Function Key

To activate the Function Key

a) During the off mode, press “Fn”

button to enter “Smart Setup”

menu. You can choose BIOS Setup

Utility, System Recovery, and other

functions in this setup menu.

b) In the Windows operation system,

press “Fn” button to initiate “Smart

Manager”.

Multi Card

Reader

Supports Secure Digital (SD),

Multi Media Card (MMC),

Memory Stick (MS),

Memory Stick PRO (MS PRO) card.

USB Port

Connects to USB devices such as USB

mouse, USB printers and USB external

HDD.

HDMI Port

Supports high denition digital video

connections.

Kensington Lock

Connects to a Kensington-compatible

computer security lock.

English

1.4 Base View

14 2 2 4

3 44

# Icon Item Description

1 Battery Bay

Houses the Notebook’s

battery pack

Battery Release

Latch

Release the battery for

removal.

Hard Disk,

Communication

and Memory Bay

Housed the Notebook’s Hard

Disk, WiFi LAN, 3.5G card

and main memory.

4 Speakers

Left and right speakers

deliver stereo audio and

Woofer speakers.

(Woofer speakers are optional)

5 SIM Card Slot

To insert of a mobile SIM

card for the 3.5G function

(Optional).

English

T1125 SERIES USER’S MANUAL

Chapter 2 Using the T1125

This chapter will briefly explain the basics of using the T1125

notebook. It will also explain any necessary precautions when using

the T1125.

English

2.1 The T1125 Keyboard

The T1125 features a Windows Compatible Keyboard.

The set language of the keyboard will depend on the region. This

section is for the English Qwerty Layout Keyboard. It is compatible

with a standard 104/105 Key Windows keyboard, accessed by using

specific key press combinations and the hotkeys. The number of

keys on the keyboard will also vary by language and region.

(English T1125 Qwerty Keyboard Layout)

The T1125 Hotkeys

The computer employs hotkeys or key combinations to access most

of the computer’s controls like screen brightness and volume output.

To activate hotkeys, press and hold the <Fn> key before pressing

the other key in the hotkey combination.

Hotkey Function Description

Fn+F1

Sleep Puts the computer in Sleep mode

Fn+F2

Wireless LAN

Enables/disables the Wireless LAN

function

Fn+F3

Brightness Down Decrease the screen brightness

Fn+F4

Brightness Up Increases the screen brightness

Fn+F5

Display Toggle

Switches display output between the

display screen, external monitor

(if connected) and both

Fn+F6

Touchpad Toggle Turns the internal touchpad on and off

Fn+F7

Speaker Toggle Turns the speaker on and off

Fn+F8

Volume Down Decreases the sound volume

Fn+F9

Volume Up Increases the sound volume

Fn+F10

WWAN Enables/disables the WWAN function

Fn+F11

Bluetooth

En a bl e s/ di s ab l es t he B lu e to ot h

function

Fn+F12

Webcam Turns the internal webcam on and off

Page is loading ...

Gigabyte T1125P User manual

Brand: Gigabyte

Model: T1125P

Category: Notebooks

Type: User manual

This manual is also suitable for

Download PDF

report

Gigabyte T1125P User manual

This manual is also suitable for

Gigabyte T1125P User manual

Related papers

Other documents